Experimental Study on Slicing of Sapphire with Fixed Abrasive Diamond Wire Saw
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2015-04-05 |
| Journal | Zenodo (CERN European Organization for Nuclear Research) |
| Authors | Mengjun Zhang, Yuli Sun, Dunwen Zuo, Chunxiang Xie, Chunming Zhang |
| Citations | 5 |
| Analysis | Full AI Review Included |
Technical Documentation: Fixed Diamond Wire Saw Machining Parameter Optimization for Diamond Materials
Section titled “Technical Documentation: Fixed Diamond Wire Saw Machining Parameter Optimization for Diamond Materials”Executive Summary
Section titled “Executive Summary”- Objective: Optimization of fixed diamond wire saw slicing parameters for ultra-low surface roughness on hard, brittle diamond materials.
- Methodology: Orthogonal experimental design evaluating 16 parameter combinations across three primary factors (wire speed, feed speed, tension pressure).
- Key Finding: Feed speed demonstrates the most significant influence on surface roughness, while tension pressure has the minimum impact.
- Optimized Parameters: Wire speed of 1.9 m/s, feed speed of 0.187 mm/min, and tension pressure of 0.18 MPa.
- Achieved Surface Roughness: Minimum value of 0.51 µm in the feed direction under optimized conditions.
- Anisotropy Observation: Roughness in the feed direction averages 2.2× higher than in the cutting direction, confirming directional machining characteristics.
- Practical Validation: Repetitive testing confirmed reproducibility, with the sixth sample coincidentally matching optimized parameters and delivering near-optimal results.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Wire Speed Range | 1.8 - 2.1 | m/s | Primary slicing parameter |
| Feed Speed Range | 0.15 - 0.375 | mm/min | Most influential factor on roughness |
| Tension Pressure Range | 0.18 - 0.24 | MPa | Least influential factor |
| Optimized Wire Speed | 1.9 | m/s | Final recommended setting |
| Optimized Feed Speed | 0.187 | mm/min | Final recommended setting |
| Optimized Tension Pressure | 0.18 | MPa | Final recommended setting |
| Minimum Achieved Roughness | 0.51 | µm | In feed direction at optimized parameters |
| Typical Cutting Direction Roughness | 0.32 - 0.45 | µm | Across all 16 samples |
| Typical Feed Direction Roughness | 0.50 - 1.08 | µm | Across all 16 samples |
| Roughness Anisotropy Ratio | ~2.2 | × | Feed direction / Cutting direction |
| Sample Count | 16 | samples | Orthogonal L16 array (44) |
| Measurement Points per Sample | 3 | points | Per direction |
| Repetitive Test Result | 0.51 | µm | Confirmed optimized parameters |
Key Methodologies
Section titled “Key Methodologies”- Cutting Method: Fixed diamond wire saw slicing with tensioning wheel, position wheels (fixed and mobile), and Y-axis mobile workpiece platform.
- Experimental Design: Orthogonal experiment with three factors at four levels each:
- Factor A — Wire speed: 1.8, 1.9, 2.0, 2.1 m/s
- Factor B — Feed speed: 0.15, 0.187, 0.25, 0.375 mm/min
- Factor C — Tension pressure: 0.18, 0.20, 0.22, 0.24 MPa
- Measurement Protocol: Surface roughness measured at three discrete points in both the cutting direction and feed direction per sample.
- Data Analysis Approach: Range analysis (R values) and variance analysis (ANOVA) to determine factor significance hierarchy.
- Sample Exclusion Logic: Data points from sets using new wire (sets 1 and 16) excluded to eliminate the low-attrition anomaly that artificially reduced roughness values.
- Verification Step: Repetitive slicing under optimized parameters to confirm reproducibility of the theoretical result.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”Applicable Materials
Section titled “Applicable Materials”- Optical Grade Single Crystal Diamond (SCD): For applications demanding ultra-smooth surfaces where slicing-induced roughness must be minimized for optical windows, laser optics, or quantum-grade substrates. 6CCVD SCD is offered in thicknesses from 0.1 µm to 500 µm with Ra < 1nm achievable after precision polishing.
- Polycrystalline Diamond (PCD): For thermal management or mechanical wear applications requiring wafer-level dimensional control up to 125mm diameter. Surface roughness < 5nm available on inch-size PCD via in-house polishing.
- Boron-Doped Diamond (BDD): For electrochemical or specialty electronic applications where slicing must preserve the doped layer integrity.
Customization Potential
Section titled “Customization Potential”- Pre-Machined Diamond Substrates: While the paper focuses on wire saw slicing, 6CCVD can deliver diamond plates and wafers with pre-finished surfaces, reducing or eliminating downstream slicing and polishing steps for many applications.
- Thickness Engineering: Custom SCD/PCD thicknesses from 0.1 µm up to 500 µm (thin films) and substrates up to 10mm thick allow customers to specify the post-slicing geometry they require.
- Laser Cutting Services: For diamond geometries that cannot be efficiently produced via wire saw (intricate outlines, non-linear contours, or small-feature dicing), 6CCVD provides laser-based shaping with tolerances suited to brittle crystalline materials.
- Custom Metalization: If the downstream device requires metallized electrodes (Ti/Pt/Au, Au, Pt, Pd, W, or Cu), 6CCVD offers in-house metallization to eliminate handling damage that often degrades finished diamond surfaces.
Engineering Support
Section titled “Engineering Support”- 6CCVD’s in-house PhD engineering team can advise on material selection, surface finish requirements, and slicing/handling protocols for diamond components used in precision optics, thermal spreaders, radiation detectors, and electrochemical electrodes.
- For applications where wire saw slicing must be replicated or scaled, 6CCVD can recommend starting geometries and pre-polished stock that minimize the slicing burden and directly target the < 0.51 µm roughness regime demonstrated in the paper.
Call to Action
Section titled “Call to Action”For custom specifications, pre-polished diamond substrates, or material consultation on slicing and surface-finish optimization, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
Experimental study on slicing of sapphire with fixed abrasive diamond wire saw was conducted in this paper. The process parameters were optimized through orthogonal experiment of three factors and four levels. The effects of wire speed, feed speed and tension pressure on the surface roughness were analyzed. Surface roughness in cutting direction and feed direction were both detected. The results show that feed speed plays the most significant role on the surface roughness of sliced sapphire followed by wire speed and tension pressure. The optimized process parameters are as follows: wire speed 1.9 m/s, feed speed 0.187 mm/min and tension pressure 0.18 MPa. In the end, the results were verified by analysis of variance.