Defects and thermoelectric performance of ternary chalcopyrite CuInTe2-based semiconductors doped with Mn
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2016-01-01 |
| Journal | Acta Physica Sinica |
| Authors | Wang Hong-Xiang, Pengzhan Ying, Yang Jiang-Feng, Shaoping Chen, Cui Jiaolin |
| Citations | 2 |
| Analysis | Full AI Review Included |
Executive Summary
Section titled “Executive Summary”- Core Innovation: Substituting low-electronegativity Mn into CuInTe2 chalcopyrite (diamond-like) lattices to engineer defect populations and decouple the interdependent Seebeck (α), electrical conductivity (σ), and thermal conductivity (κ) parameters.
- Defect Engineering Mechanism: At low Mn content (x < 0.1), Mn preferentially occupies In sites, forming acceptor defects (Mn-In) that elevate carrier concentration and electrical conductivity.
- Dual-Site Occupation Discovery: At higher Mn content (x ≥ 0.1), Mn simultaneously occupies In and Cu sites, creating competing donor (Mn+Cu) and acceptor (Mn-In) defects that undergo annihilation, stabilizing carrier concentration.
- Optimal Performance Achieved: Maximum ZT = 0.84 at 810.0 K for Cu0.95InMn0.05Te2 — approximately 2× the undoped baseline and superior to prior Zn-doped analogs (ZT = 0.69).
- Key Peak Properties: Seebeck coefficient α reaches 353.8 µV·K-1 at 443.0 K; electrical conductivity σ = 2.3 × 104 Ω-1·m-1 at 810 K; lattice thermal conductivity κL suppressed to 0.67 W·K-1·m-1 at 810 K.
- Structural Insight: Anion displacement parameter u trends toward the ideal 0.25, and tetragonal distortion η trends toward 1.0 as Mn content increases, enabling controlled phonon scattering without aggressive thermal conductivity penalties.
- Synthesis Method: Vacuum-sealed quartz tube melting at 1373 K, homogenization annealing at 650 K for 240 h, mechanical alloying, and Spark Plasma Sintering (SPS) at 843 K / 50 MPa.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Optimal Composition | Cu0.95InMn0.05Te2 | — | Highest ZT doping level |
| Peak ZT | 0.84 | dimensionless | At 810.0 K |
| Peak Seebeck Coefficient (α) | 353.8 | µV·K-1 | At 443.0 K (x = 0.05) |
| Seebeck Coefficient at 810 K | 229.0 | µV·K-1 | High-temperature limit |
| Electrical Conductivity (σ) | 2.3 × 104 | Ω-1·m-1 | At 810 K (x = 0.05) |
| Maximum σ | 2.13 × 104 | Ω-1·m-1 | At 718.0 K (x = 0.1) |
| Carrier Concentration (n) | 1.0 × 1024 | m-3 | Maximum at x = 0.1 |
| Carrier Mobility (µ) | 1.50 × 10-2 | m2·V-1·s-1 | Maximum at x = 0.05 |
| Lattice Thermal Conductivity (κL) | 0.67 - 0.94 | W·K-1·m-1 | Range at 810 K across x |
| Bandgap (Eg) | 0.70 - 0.78 | eV | Optical absorption edge |
| Melting Temperature | 1373 | K | Maximum synthesis temperature |
| Annealing Temperature | 650 | K | Homogenization hold |
| Annealing Duration | 240 | h | Single-phase chalcopyrite formation |
| SPS Sintering Temperature | 843 | K | Densification |
| SPS Pressure | 50 | MPa | Vacuum environment |
| Ball Milling Speed | 350 | r/min | Mechanical alloying |
| Ball Milling Duration | 5 | h | Powder refinement |
| Lattice Constant (a) | 6.2070 - 6.2148 | Å | Across x = 0.02 to 0.2 |
| Lattice Constant (c) | 12.4712 - 12.4762 | Å | Across x = 0.02 to 0.2 |
| Anion Position (u) | 0.2477 - 0.2483 | — | Approaches ideal 0.25 |
| Tetragonal Distortion (η) | 1.0034 - 1.0046 | — | Approaches ideal 1.0 |
| Test Temperature Range | RT - 810 | K | Full characterization span |
| Measurement Uncertainty (α, σ) | < 7 | % | ZEM-3 instrument error |
| Lorenz Number (L0) | 2.0 × 10-8 | W·Ω·K-2 | Wiedemann-Franz calculation |
Key Methodologies
Section titled “Key Methodologies”- Material Design: Cu-poor Cu1-xInMnxTe2 compositions with x = 0, 0.02, 0.05, 0.1, 0.2, and 0.3 were formulated to ensure sufficient Mn occupancy at Cu sites.
- Raw Material Preparation: High-purity (≥ 5N) Cu, In, Te elements and MnTe were loaded and vacuum-sealed in quartz tubes.
- Melting Synthesis: Tubes were heated to a maximum of 1373 K and held for 24 h to achieve molten-state alloying.
- Controlled Cooling & Annealing: Melt was slow-cooled to 650 K with a 240 h isothermal hold to guarantee single-phase chalcopyrite crystallization, followed by cooling to room temperature.
- Powder Processing: Ingots were crushed, ball-milled at 350 r/min for 5 h, and dried to obtain homogeneous feedstock.
- Spark Plasma Sintering (SPS-1030): Consolidation under vacuum at 843 K and 50 MPa to produce dense bulk specimens.
- Sample Geometries: Two configurations were pressed — 12.0 mm × 3 mm × 2.5 mm bars for electrical measurements and ϕ10.0 mm × 1 mm discs for thermal measurements.
- Structural Characterization: XRD (Cu Kα, λ = 0.15406 nm) over 10° ≤ 2θ ≤ 140° with Rietveld refinement via GSAS software to determine site occupancy factors (SOFs) and lattice parameters.
- Compositional Analysis: XPS core-level spectroscopy (Mn 2p3/2, Cu 2p3/2, In 3d5/2, Te 3d5/2) with Ar+ ion sputtering for bonding state confirmation.
- Optical Characterization: UV-Vis-NIR spectrophotometry (Perkin-Elmer Lambda 950) for bandgap determination.
- Hall Measurement: PPMS at ±1.5 T magnetic field on 2 × 2 × 7 mm3 samples for carrier concentration and mobility extraction.
- Thermoelectric Testing: ULVAC ZEM-3 for simultaneous Seebeck coefficient and electrical conductivity under He atmosphere; TC1200RH laser flash for thermal diffusivity and heat capacity in vacuum.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”While the chalcopyrite CuInTe2 system investigated here differs fundamentally from diamond materials, the research underscores a universal engineering challenge — the simultaneous optimization of carrier transport, thermal transport, and structural integrity. This is precisely the design territory where high-performance diamond substrates and CVD-diamond thermal management components deliver transformative value.
| Research Requirement from Paper | 6CCVD Capability Match |
|---|---|
| High-temperature stability up to 810 K for TE module housings | SCD/PCD plates rated for > 800 K continuous service |
| Precise control over lattice thermal conductivity | PCD grain-size engineering (µm to nm-scale crystallites) |
| Decoupling of electrical and thermal transport pathways | Boron-Doped Diamond (BDD) with tunable carrier concentration |
| SPS-compatible substrate backing for layered device stacks | Custom-dimension PCD plates up to 125 mm diameter |
| Metallization for electrode contacts (Au, Pt, Ti compatible) | In-house Au, Pt, Pd, Ti, W, Cu metallization |
| Tight geometric tolerances for miniaturized TE legs | Laser cutting and precision dicing to ± 25 µm |
| Surface finish requirements for thermal interface bonding | PCD polishing to Ra < 5 nm (inch-scale), SCD to Ra < 1 nm |
| Repeated thermal cycling durability | Diamond’s unmatched thermal shock resistance (CTE ~1 ppm·K-1) |
Applicable Materials
Section titled “Applicable Materials”For thermal management and electrode integration in chalcopyrite-based thermoelectric module assemblies, the following 6CCVD materials are directly relevant:
- Optical Grade SCD — For high-thermal-conductivity heat spreaders backing TE legs where minimal phonon scattering at the interface is critical.
- Heavy Boron-Doped PCD (BDD) — For electrically conductive, thermally robust electrode interconnects that can simultaneously carry current and dissipate Joule heat.
- Standard PCD Plates — For structural support plates and module housings demanding matched thermal expansion with adjacent semiconductor stacks.
- Substrate-Grade PCD (up to 10 mm thickness) — For bulk heat sinks and cold-side fixture plates in mid-to-high temperature (300 K - 810 K) operating regimes.
Customization Potential
Section titled “Customization Potential”- Custom Dimensions: While this paper pressed specimens in 12 mm × 3 mm × 2.5 mm and ϕ10 mm × 1 mm formats, 6CCVD routinely supplies custom plate geometries up to 125 mm diameter for PCD, with thickness spanning 0.1 µm to 500 µm for freestanding SCD/PCD films and up to 10 mm for substrate-grade material.
- Metallization Integration: Multi-layer metal stacks such as Ti/Pt/Au — standard in semiconductor device fabrication — can be deposited in-house using 6CCVD’s metallization line (Au, Pt, Pd, Ti, W, Cu), eliminating external supply-chain steps.
- Laser Cutting & Dicing: Prototype TE module layouts requiring isolated thermal legs, contact pads, or via structures can be precision-cut to drawing specifications.
- Surface Engineering: Nano-polished interfaces (Ra < 1 nm SCD, < 5 nm PCD) ensure optimal thermal contact resistance when bonded to chalcopyrite legs or metallization layers.
Engineering Support
Section titled “Engineering Support”6CCVD’s in-house PhD materials team can assist with substrate selection, metallization stack design, and thermal-mechanical integration for thermoelectric device packaging. Whether you are scaling chalcopyrite module production from laboratory pellets to multi-leg generator arrays, or developing next-generation high-temperature waste-heat recovery systems operating near 800 K, our engineers can recommend the optimal diamond grade, geometry, and surface finish to match your thermal budget and mechanical constraints.
For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
In thermoelectric (TE) semiconductors, there are three physical parameters that govern the TE performance (i.e. Seebeck coefficient (), electrical conductivity (), and thermal conductivity ()); they are interrelated, hence it is hard to optimize them simultaneously. In order to improve the TE performance, we need to further explore new materials. Ternary chalcopyrite (diamond-like) I-III-VI2 semiconductors (Eg = 1:02 eV) are new materials of the TE family, which have potential in conversion between heat and electricity. Since in the ternary chalcopyrite structure, such as Cu(Ag) MTe2, there is an inherent Coulomb attraction between charged defects MCu(Ag)2+ and 2VCu(Ag)- (a native defect pair, i.e., metal M-on-Cu or Ag antisites and two Cu or Ag vacancies), hence the electronic and structural properties can easily be tailored if these two defects, along with the creation of other defects, are modified through the introduciton of foreign elements. Besides, the ternary I-III-VI2 compounds often show tetragonal distortion because 0.25, = c/2a 1 (here and are the anion position displacement parameters, and a and c are the lattice parameters), and the cationanion distances are not equal (dCuTedInTe). Any occupation by foreign elements in the cation sites of I-III-VI2 will cause the redistribution of bond charges between I-VI and III-VI, thus leading to a tiny adjustment of the crystal structure and altering the phonon scattering behavior. In this work, we substitute Mn for Cu in the chalcopyrite CuInTe2 and prepare the Cu-poor Cu1-xInMnxTe2 semiconductors. Investigations of Z-ray patterns after Rietveld refinement reveal that Mn prefers In to Cu lattice sites for low Mn content (x 0.1), thus creating MnIn- as an active acceptor, and improving the carrier concentration (n) and electrical conductivity as Mn content increases. However, Mn can either occupy In or Cu sites simultaneously when x 0.1, and generate both the donor defect MnCu+ and the acceptor defect MnIn-. In this case, annihilation may occur between these two defects, allowing the reduction in both the defect and carrier concentrations. Because of the annihilation between the two defects, two values (|| = |-0.25| and ||= |-1.0|) reduce, this only yields a subtle change in the difference between mean cation-anion distance (RInTe-RCuTe), indicating a small distortion tendency in lattice structure as Mn content increases. Because of this, there is a limited enhancement in lattice thermal conductivity (L) at high temperatures. As a consequence, we attain an optimal TE performance at a certain Mn content (x = 0.05) with the dimensionless figure of merit (ZT) ZT = 0.84 at 810.0 K, which is about twice as much as that of Mn-free CuInTe2.