Skip to content

High Power Diamond Raman Lasers

MetadataDetails
Publication Date2018-04-16
JournalIEEE Journal of Selected Topics in Quantum Electronics
AuthorsRobert J. Williams, Ondřej Kitzler, Zhenxu Bai, Soumya Sarang, Hadiya Jasbeer
InstitutionsMacquarie University, Defence Science and Technology Group
Citations100
AnalysisFull AI Review Included
  • Demonstrated Dominance: Diamond Raman Lasers (DRLs) have achieved 750 W CW/quasi-CW output power, currently the highest among all end-pumped bulk-crystal oscillators, surpassing non-diamond Raman crystals by 2-3 orders of magnitude.
  • Material Superiority: Diamond’s thermal conductivity is ~150x that of Nd:YAG and ~60x that of sapphire; calculated on-axis temperature rise for 1 kW pump power at 100 µm radius is only 4.3°C (vs. >1100°C in Nd:YAG).
  • Wavelength Versatility: Demonstrated output from 273 nm (deep UV) to 3800 nm (first Stokes) and 7300 nm (second Stokes), achieved via cascaded Stokes and intracavity harmonic generation.
  • Brightness Enhancement: Raman beam cleanup and combining enable large-factor brightness improvements for low-coherence, multimode inputs—critical for direct diode pumping.
  • Power Scaling Roadmap: Projections indicate potential for >105 W from a single diamond element using thermal mitigation (isotopically enriched 12C diamond, cryogenic operation, slab/waveguide geometries).
  • Key Limiter Identified: Thermo-optic lensing (rather than stress fracture or birefringence) is the primary power-limiting mechanism—calculations for the 380 W DRL predicted ≥83 diopters of thermal lensing with no observed degradation, indicating heat deposition may be more diffuse than modeled.
ParameterValueUnitContext / Condition
Raman linewidth (FWHM)45GHzDiamond at 1 µm pump
Raman gain coefficient (gR)~10cm/GWTypical for Raman crystals
Pump spot radius (modeled)100µmEnd-pumped geometry
Maximum CW/quasi-CW output power750WNd:YAG pump, >0.25 ms duration
Output power (5 s duration)154WSeeded-fiber amplifier pump
Output power (10 ms duration)380W61% conversion efficiency
100 W milestone100WQuasi-CW Nd:YAG pump (0.2 ms)
Conversion efficiency (record)61%380 W result, 10 ms pulse
Thermal lens strength (predicted)≥83diopters380 W DRL condition
Predicted on-axis ΔT (1 kW, 100 µm)4.3°CDouble-pass, 82% pump depletion
Nd:YAG equivalent power for same ΔT1.5WDemonstrates diamond’s thermal advantage
Nd:YAG fracture threshold22W1.1 at.% doped, end-pumped
First Stokes wavelength range1240-1485nmFrom 1064 nm pump
Second Stokes output power>300WAt 1.49 µm (820 W pump)
Second Stokes (max reported)>300W1.49 µm, efficiency near model
Output wavelength (shortest)273nmDeep UV, cascaded
Output wavelength (longest, 1st Stokes)3800nmContinuously tunable 3.38-3.80 µm
Output wavelength (longest, 2nd Stokes)7300nmMid-IR extension
Optical phonon decay timescale~10-10sHot phonon lifetime
Stress-fracture limit (projected)~1MWSingle-element DRL
Continuous power (thermal model)>105WWith isotopic/cryogenic enhancements
On-axis ΔT threshold (Nd:YAG comparison)4.3°CEquals diamond 1 kW case
Pump absorption coefficient (model)0.106mm-1Approximating 82% depletion
Loss at 2.46 µm (4th Stokes)0.3cm-1Multi-phonon absorption
Loss at shorter Stokes wavelengths0.0038cm-1Intrinsic low-loss regime
Fiber Raman benchmark3.89kW1123 nm, comparison reference
  1. Pump Source Selection: Use narrow-linewidth (40-55 GHz) CW or pulsed Nd:YAG (1064 nm) and Yb-doped fiber amplifiers (kW-class) to satisfy diamond’s strict pump bandwidth requirements (must be <45 GHz for full gain).
  2. End-Pumping Geometry: Focus pump to ~50-100 µm waist radius inside the diamond crystal; double-pass configuration to achieve high pump depletion (~82%).
  3. Crystal Mounting: Maintain crystal faces at fixed temperature; bottom face anchored to room-temperature heatsink for thermal modeling baseline.
  4. Cavity Design for Cascaded Stokes:
    • Even Stokes orders (2nd, 4th): High output coupling (50-95%)
    • Odd Stokes orders (3rd): Low output coupling (&lt;10%)
    • Cavity low-loss for all lower-order Stokes fields
  5. Single Longitudinal Mode (SLM) Operation: Exploit lack of spatial hole burning in Raman gain via ring cavity geometry with waveplates and Faraday rotator for unidirectional operation; pump linewidth &lt;2.6 GHz demonstrated.
  6. Beam Combining: Use non-collinear geometry in diamond amplifier; multiple pump beams overlap in Raman gain region for coherent combining.
  7. Frequency Doubling: Intracavity LBO crystal for second-harmonic generation (e.g., yellow 559-590 nm); optimize diamond-LBO separation and Stokes waist (typically 50-200 µm).
  8. Quasi-CW Testing: Use pulse durations of 0.2-10 ms to reach steady-state thermal conditions for CW scaling predictions.
  • Optical-Grade Single Crystal Diamond (SCD): This research demands extremely low-bulk-loss, low-birefringence CVD diamond suitable for high-finesse Raman cavities. 6CCVD’s SCD with Ra &lt;1 nm polishing is ideally suited for end-face coatings (HR/AR dielectric stacks) required for the cavity mirrors used in these experiments.
  • Isotopically Enriched 12C SCD: The paper explicitly identifies isotopically pure diamond as a key pathway to mitigating thermal lensing and reaching >105 W operation. 6CCVD offers custom isotopic enrichment consultation for thermal management research.
  • Thick SCD Substrates (up to 10 mm): For high-power oscillator designs requiring longer interaction lengths to manage thermal gradients and reduce flux density.
  • Dimensional Control: The paper references specific crystal lengths and pump spot geometries (50-100 µm waists). 6CCVD can deliver custom-cut SCD plates with dimensional tolerances suitable for tight-focus end-pumped cavities, including laser-cut exotic geometries for monolithic or semi-monolithic resonator designs.
  • Surface Finishing: Sub-nanometer polishing (Ra &lt;1 nm) is critical for minimizing scattering losses in high-finesse Raman cavities. 6CCVD’s in-house polishing capability meets the stringent flatness and roughness requirements for low-loss AR/HR coatings at 1064 nm, 1240 nm, and Stokes wavelengths.
  • Metalization Services: For hybrid integration, heat-spreader bonding, or packaging into conduction-cooled mounts, 6CCVD offers Ti/Pt/Au, Au, and W metalization to facilitate soldering or thermocompression bonding to diamond heat sinks.
  • AR/HR Coating Partnerships: While 6CCVD specializes in the diamond substrate, we collaborate with leading coating houses and can deliver diamond with customer-specified coating prescriptions.
  • PhD-Level Consultation: 6CCVD’s in-house PhD engineering team can assist with material selection for high-power Raman laser projects, including guidance on:
    • Birefringence optimization for polarization-sensitive cavity designs
    • Trade-offs between crystal length, pump geometry, and thermal lensing
    • Selection of natural-abundance vs. isotopically enriched diamond for thermal management
    • Characterization data (Raman maps, bulk loss measurements, stress birefringence imaging) to qualify diamond for specific oscillator or amplifier architectures
  • Application-Specific Guidance: For researchers replicating or extending the wavelength conversion results (UV to mid-IR), 6CCVD can advise on optimal diamond specifications for cascaded Stokes configurations and intracavity harmonic generation setups.

For custom specifications, isotopically enriched diamond sourcing, or material consultation for your high-power laser project, visit 6ccvd.com or contact our engineering team directly. Global shipping available (DDU default, DDP on request).

View Original Abstract

Laser gain materials possessing high thermal conductivity and robust mechanical properties are key prerequisites for high power lasers. We show that diamond, when configured as a Raman laser, enables access to these and other extreme properties, providing an important new route to high power and high brightness beam generation. Recent achievements in pulsed and continuous wave oscillators, beam combining amplifiers, and single longitudinal mode oscillators are summarized, along with wavelength extension of these concepts through adaption to other pumps, use of Raman cascading, and intracavity harmonic generation. To date, diamond laser powers have attained 750 W with efficiency and beam quality so far unperturbed by nonlinear or thermally induced side-effects. Large factor brightness enhancement of low coherence inputs is demonstrated using multiple pump beams (via Raman beam combination) or highly multimode pumps for oscillator and amplifier configurations. Future directions for direct diode pumping, and for realizing extraordinary power and power density through reduced temperature operation and isotopically enriched diamond, are also discussed. Our results indicate that diamond is emerging as a generic high-power laser technology with advantages in terms of brightness (high average power and high beam quality) and wavelength range.