Performance of CVD diamond single crystals as side-bounce monochromators in the Laue geometry at high photon energies
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2019-01-01 |
| Journal | AIP conference proceedings |
| Authors | S. Stoupin, T. Krawczyk, J. P. C. Ruff, Ken Finkelstein, H H Lee |
| Institutions | Cornell University, Pohang University of Science and Technology |
| Citations | 1 |
| Analysis | Full AI Review Included |
Executive Summary
Section titled “Executive Summary”- Application: Side-bounce Laue geometry x-ray monochromators for high-energy synchrotron radiation (≳ 20 keV).
- Material: Chemical vapor deposited (CVD) single crystal diamond (SCD) plates evaluated against high-pressure high-temperature (HPHT) type IIa diamond crystals.
- Performance: Demonstrated up to 10× enhancement in reflected x-ray flux compared to HPHT IIa diamond plates under in-operando high-heat-load conditions.
- Operating Conditions: Tested at the A1 undulator station of Cornell High Energy Synchrotron Source (CHESS); photon energies evaluated at ~46 keV.
- Beam Focusing: Pt-coated mono capillary optics delivered ~25 × 25 µm² focused spots with a measured flux of ~1 × 10¹⁰ photons/s.
- Key Challenge Identified: Intrinsic lattice bending causes wavefront distortions (defocusing or focusing depending on bend direction), requiring ex-situ rocking curve topography screening prior to deployment.
- Fabrication Method: Microwave plasma-assisted CVD (MPCVD) used to produce plates with homogeneous distribution of mosaic blocks enabling reflectivity exceeding perfect crystal predictions by an order of magnitude.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Photon Energy Range | ≳ 20 | keV | High-energy Laue monochromator operation |
| Tested Photon Energy | 46 | keV | Demonstrated beam focusing via capillary |
| Flux Enhancement vs. HPHT IIa | Up to 10× | ratio | Side-bounce Laue geometry |
| Focused Beam Flux | ~1 × 10¹⁰ | photons/s | Post-capillary optics output |
| Focused Spot Size | ~25 × 25 | µm² | Pt-coated mono capillary, nominal |
| Horizontal Beam Profile (Focused) | ~21 | µrad (FWHM) | Measured divergence after capillary |
| Vertical Beam Profile (Focused) | ~16 | µrad (FWHM) | Measured divergence after capillary |
| Beam Footprint (CVD-1, undistorted reference) | ~5 | mm | Expected from geometric preservation |
| Beam Footprint (CVD-1, defocused) | ~11 | mm | Observed at detector (~2 m) |
| Beam Footprint (CVD-2, focused) | ~2 | mm | Observed at detector (~2 m) |
| Recommended Plate Thickness (Laue, nonabsorbing limit) | 0.5 - 1 | mm | Approaching R → 1/2 reflectivity limit |
| Intrinsic Relative Bandwidth (111 reflection) | ε₁₁₁ ≈ 5 × 10⁻⁵ | ratio | Perfect crystal reference |
| Total Radiation Bandwidth at CHESS | ∆E/E ≈ 1 × 10⁻³ | ratio | Source-size dominated, L ≈ 15 m |
| Source Divergence (CHESS A1) | ψ₀ ≈ 140 | µrad | Scattering-plane divergence |
| Bragg Angle Approximation | tan θ ≈ 0.1 | - | Shallow-angle, high-E low-index reflections |
| Horizontal Source Size Range | 200 - 600 | µm | 3rd-generation synchrotron baseline |
| Source-to-Monochromator Distance | ~15 - 30 | m | Beamline-dependent |
| Angular Misorientation (CVD plates) | ρ ≈ 2.355 × ∆θσ | µrad | Derived from Gaussian rocking curve width |
| Reflectivity Limit (Thick, Nonabsorbing Laue) | 0.5 | ratio | Theoretical maximum |
Key Methodologies
Section titled “Key Methodologies”- Crystal Selection & Preparation
- Use of CVD single crystal diamond plates with homogeneous distribution of mosaic blocks (block thickness + angular misorientation ensemble).
- Ex-situ rocking curve topography performed to map intrinsic lattice strain and pre-screen plates for thermal-load suitability.
- Diffraction Geometry
- Side-bounce Laue (transmission) geometry with horizontal scattering plane at shallow Bragg angles.
- Optimization criterion via geometric optics: maximize footprint efficiency for low-index reflections at high photon energies.
- In-Operando High-Heat-Load Testing
- Monochromator installation at A1 undulator station, CHESS.
- Plates operated under full synchrotron undulator radiation load to evaluate reflectivity and thermal behavior.
- Wavefront Characterization
- Analyzer-based x-ray diffraction imaging using a 0.5-mm-thick Si wafer analyzer (nondispersive double-crystal arrangement).
- d-spacing matched between analyzer Si reflection and working diamond reflection.
- Area detector placed ~2 m from monochromator for rocking curve topograph acquisition.
- Beam Focusing
- Pt-coated mono capillary (100 mm length, 56 mm focal distance).
- Capillary apertures: ~600 µm entrance, ~400 µm exit clearance.
- Input beam collimated to 600 × 600 µm² via x-ray slits.
- Gold bead (400 µm diameter) blocks direct center beam to enforce grazing-incidence reflection.
- Quantitative Metrics
- IRint - integrated reflected intensity normalized to maximum.
- δθm - rocking curve peak position map.
- ∆θσ - Gaussian width (standard deviation) map.
- Focused beam flux verified via downstream ionization chamber.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”<table> <thead> <tr><th>Capability</th><th>Relevance to This Research</th></tr> </thead> <tbody> <tr> <td>Applicable Material</td> <td>
Optical Grade Single Crystal Diamond (SCD) grown via MPCVD — matches the high-crystal-quality, large-area, controlled mosaic-block distribution requirements for high-heat-load monochromators. Plates with a homogeneous defect distribution (mosaic ensemble) are needed to exceed perfect-crystal reflectivity by an order of magnitude.
</td> </tr> <tr> <td>Thickness Range</td> <td>
6CCVD provides SCD plates from 0.1 µm to 500 µm, with substrate capability up to 10 mm. The 0.5-1 mm thickness window recommended for nonabsorbing Laue reflectivity (R → 1/2) falls squarely within 6CCVD’s substrate and thick-plate manufacturing capability.
</td> </tr> <tr> <td>Custom Dimensions</td> <td>
Plates and wafers can be customized up to 125 mm — accommodating the side-bounce plate geometries used in this study and allowing large-aperture configurations for next-generation beamlines.
</td> </tr> <tr> <td>Surface Finish & Polishing</td> <td>
Ra < 1 nm surface polish on SCD ensures low surface strain that minimizes unwanted wavefront distortion — directly addressing the lattice bending issue flagged in this paper.
</td> </tr> <tr> <td>Metalization (Pt / Au / Ti)</td> <td>
This study’s capillary optics rely on Pt coatings for high-E grazing-incidence reflectivity. 6CCVD offers in-house Pt, Au, and Ti metalization suitable for capillary, slit, and mounting hardware — enabling integrated material + optic component packages.
</td> </tr> <tr> <td>Laser Cutting & Dicing</td> <td>
Custom diamond plate geometries required for side-bounce monochromator mounts can be produced with laser cutting and dicing services, including non-standard aspect ratios.
</td> </tr> <tr> <td>Engineering Support</td> <td>
6CCVD’s in-house PhD team can guide mosaic-block engineering, thickness selection (0.5-1 mm Laue range), and pre-screening protocols (analogous to rocking curve topography) for high-heat-load Laue monochromator projects.
</td> </tr> <tr> <td>Recommended Configuration</td> <td>
Optical Grade SCD plate, 0.5-1 mm thickness, 100 orientation, Ra < 1 nm polish, pre-characterized rocking curve topography for bend minimization. Suitable for side-bounce Laue monochromator deployment at synchrotron beamlines operating ≳ 20 keV.
</td> </tr> </tbody> </table>
> For custom specifications, mosaic characterization, or material consultation on synchrotron-grade diamond components, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
We report on performance of chemical vapor deposited (CVD) single crystal\ndiamond plates as side bounce monochromators for high photon energies\n($\gtrsim$~20 keV) in the Laue geometry. Several crystals were tested\nin-operando high-heat-load conditions at A1 undulator station of Cornell High\nEnergy Synchrotron Source. Up to 10$\times$ enhancement in the reflected x-ray\nflux was observed compared to that delivered by IIa diamond plates grown by\nhigh-pressure high-temperature method. Wavefront distortions were measured\nusing analyzer-based x-ray diffraction imaging. Focusing of a portion of the\nreflected beam was demonstrated using Pt-coated mono capillary optics at a\nphoton energy of 46 keV.\n