Skip to content

Modification of boron-doped diamond with gold-palladium nanoparticles for CO2 electroreduction

MetadataDetails
Publication Date2020-04-29
JournalIOP Conference Series Materials Science and Engineering
AuthorsA Kumik, Tribidasari A. Ivandini, Rahmat Wibowo
InstitutionsUniversity of Indonesia
Citations5
AnalysisFull AI Review Included

Modification of Boron-Doped Diamond with AuPd Nanoparticles for CO2 Electroreduction — Technical Documentation

Section titled “Modification of Boron-Doped Diamond with AuPd Nanoparticles for CO2 Electroreduction — Technical Documentation”
  • Core Objective: Evaluate bimetallic gold-palladium core-shell nanoparticles (AuPdNPs) immobilized on boron-doped diamond (BDD) as a catalytic platform for electrochemical CO2 reduction.
  • Electrode Architecture: AuPd nanoparticles (≈40 nm, flower-like morphology) are anchored to allylamine-terminated BDD through amine-metal affinity chemistry.
  • Surface Coverage Achieved: Au ≈ 4.4 %; Pd ≈ 6.0 % of the BDD working area, confirmed via EDX mapping.
  • Electrolyte System: Two-compartment H-cell — cathode chamber 0.1 M NaCl, anode chamber 0.1 M Na2SO4.
  • Operating Potential: −0.9 V vs. Ag/AgCl applied for 60 minutes.
  • Performance Metric: Faradaic efficiency ≈ 84.65 % with acetic acid (CH3COOH) detected as a primary C2 product.
  • Significance: Demonstrates that heavy boron-doped diamond coupled with bimetallic nanostructures can selectively drive CO2-to-C2 conversion, a pathway with high industrial value.
ParameterValueUnitContext
Substrate MaterialBoron-Doped Diamond (BDD)—Working electrode base
Surface TerminationAllylamine (UV, 6 h)—Functionalization for NP immobilization
Au Surface Coverage4.4%Determined by EDX
Pd Surface Coverage6.0%Determined by EDX
Nanoparticle MorphologyFlower-like (anisotropic)—TEM imaging
Average NP Diameter≈ 40nmTEM measurement
LSPR Peak Range500-600nmUV-Vis absorbance of AuPd colloid
Applied Potential−0.9V vs. Ag/AgClElectrolysis working potential
Electrolysis Duration60minPer reduction cycle
Cathode Electrolyte0.1 M NaCl—CO2-saturated chamber
Anode Electrolyte0.1 M Na2SO4—Counter chamber
Cell ConfigurationTwo-compartment (H-cell)—Separator-isolated chambers
Faradaic Efficiency84.65%Toward acetic acid product
Primary ProductAcetic acid (CH3COOH)—C2 hydrocarbon target
  1. BDD Surface Functionalization: Boron-doped diamond substrates were amino-terminated by immersion in allylamine under UV irradiation for 6 hours to generate amine-rich binding sites.
  2. Au Nanoparticle Synthesis: Colloidal gold nanoparticles (AuNPs) were prepared via a wet-chemical reduction route.
  3. Pd Shell Growth: Palladium was deposited onto the AuNP cores, yielding flower-like AuPd core-shell nanostructures (≈40 nm).
  4. Nanoparticle Immobilization: The amine-terminated BDD was immersed in the colloidal AuPd suspension to anchor the nanoparticles via Au-N / Pd-N coordination.
  5. Physicochemical Characterization: TEM confirmed morphology and particle size; UV-Vis spectroscopy confirmed plasmonic signature; EDX quantified elemental surface coverage.
  6. Electrochemical Assembly: A two-compartment H-cell was assembled with a Nafion-type separator; catholyte 0.1 M NaCl (CO2-saturated), anolyte 0.1 M Na2SO4.
  7. Bulk Electrolysis: A constant potential of −0.9 V vs. Ag/AgCl was applied for 60 minutes.
  8. Product Analysis: Liquid products were analyzed to determine Faradaic efficiency and identify the acetic acid fraction.
Research Requirement6CCVD Capability
Heavy boron-doped BDD substrate with metallic conductivityHeavy Boron-Doped PCD and Boron-Doped SCD available; doping levels tailored to deliver sub-100 mΩ·cm resistivity for electrolysis-grade performance.
Low-Ra, uniform electrode surface for reproducible NP anchoringPolishing to Ra < 5 nm on inch-size PCD and Ra < 1 nm on SCD, providing the smooth, defect-controlled interface needed for uniform allylamine grafting.
Custom wafer dimensions for H-cell integrationPCD plates/wafers up to 125 mm and thicknesses from 0.1 µm to 500 µm (SCD/PCD), enabling direct substitution into customer-specific electrochemical cells.
Optional conductive metal back-contactInternal metalization (Au, Pt, Pd, Ti, W, Cu) available for sputter or e-beam deposition to ensure low ohmic contact resistance with the cell current collector.
Reproducible, large-area surface chemistrySubstrate-level Ra control and surface planarity critical for uniform allylamine UV-termination; 6CCVD’s polishing tolerances support consistent functionalization across full wafers.
Rapid iteration between electrode geometriesCustom laser cutting available to define electrode footprints, exposed windows, and contact pads from standard or non-standard wafer sizes.
  • Applicable Materials: Heavy Boron-Doped PCD (preferred for low-cost, large-area electrocatalytic electrodes) or Boron-Doped SCD (preferred when single-crystal surface reproducibility and lowest background current are required). For studies targeting extended electrochemical windows during CO2 reduction, our high-quality BDD films with controlled sp3 content are the recommended starting point.

  • Customization Potential: The reported AuPd catalyst chemistry can be supported on any 6CCVD-supplied BDD geometry, including non-standard thicknesses and shapes via laser cutting. If a back-contact such as Ti/Pt/Au is required to suppress contact resistance during long-duration bulk electrolysis, 6CCVD can deliver this metalization stack in-house — no third-party processing needed.

  • Engineering Support: 6CCVD’s in-house PhD team can assist with material selection, doping-level optimization, and metalization strategy for similar CO2 electroreduction and bimetallic catalyst support projects. We routinely consult on boron-doping concentrations, surface termination compatibility, and electrode geometry trade-offs for electrochemistry platforms.

  • Call to Action: For custom specifications, metalization stacks, or material consultation on CO2 reduction electrode design, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

Modification of boron-doped diamond (BDD) with gold-palladium nanoparticles (AuPdNPs) was performed for an application in electrochemical reduction of CO2. Preparation of the colloidal AuPdNPs involved two steps, including the synthesis of gold nanoparticles (AuNPs) and the growth of palladium on the surface of AuNPs. BDD, which had been terminated with allylamine under UV light irradiation for6h, then, was immersed in the colloidal AuPdNPs. Characterization of the nanoparticles by using Tunneling Electron Microscopy (TEM) showed flowers-like nanoparticles with an average size of 40 nm, while characterization of the modified BDD showed the Au and Pd surface coverage of 4.4 % and 6.0 %, respectively, on BDD surface. The electrochemical reduction of CO2at the modified BDD was performed in a two-compartments cell with 0.1 M NaCl solution in the cathode chamber and 0.1 M Na2SO4solution in the anode chamber. By applying the potential -0.9 V (vs. Ag/AgCl) in the system for 60 min, it showed the faradaic efficiency of the system at approximately 84.65 % with acetic acid as one of the products.