Evaluation of the wear of the duckfoot sweep cultivator blades and the technology of their hardening
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2021-06-23 |
| Journal | PROBLEMS OF TRIBOLOGY |
| Authors | Т. С. Скобло, Ivan Rybalko, Alexander Nanka, O Saychuk |
| Institutions | Kharkiv Petro Vasylenko National Technical University of Agriculture |
| Citations | 1 |
| Analysis | Full AI Review Included |
Executive Summary
Section titled “Executive Summary”- Application: Abrasive-wear protection of thin-walled duckfoot sweep cultivator blades, with damage concentrated at the point tip and wing regions.
- Baseline failure mode: Approximately 60% of blades lose working capacity through tip and wing wear; observed service loss reached 30 mm at the point tip and 15 mm across the wings, with blade thickness reduced by approximately 1-1.5 mm.
- Hardfacing approach: Local carbide-containing T-620 electrode overlays were placed only in the highest-wear regions, minimizing heat input and preserving the thin steel substrate.
- Diamond-assisted modification: A non-magnetic fraction from ammunition-disposal detonation charge was introduced as an electrode modifier. Its nano- and dispersed diamond content acted as nucleation sites and “micro-refrigerators,” refining the carbide phase and changing the liquid-bath crystallization range.
- Structural result: Chromium distribution became approximately 2.2 times more uniform; average carbide-phase share increased by 27% at the surface, 32% in the middle, and 70% in the transition zone relative to conventional hardfacing.
- Tribological result: Modified T-620 hardfacing reduced abrasive mass loss from 0.0145 g for untreated 65G steel to 0.0044 g, corresponding to approximately 3.3 times lower wear and about 3 times the relative wear resistance reported by the authors.
- Recommended geometry: Front-face reinforcement of a 20 mm point-tip stripe; rear-face reinforcement of 12-15 mm wing stripes, with at least 10 mm spacing to prevent overlapping heat-affected zones.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Blade substrate | 65G | — | Carbon-steel cultivator blade baseline |
| Predominant point-tip wear | 30 | mm | Typical service damage reported |
| Predominant wing-width wear | 15 | mm | Typical service damage reported |
| Blade-thickness loss | 1-1.5 | mm | Operational wear before restoration hardfacing |
| Blades losing working capacity in affected regions | ~60 | % | Primarily point-tip and wing wear |
| Residual resource after conventional reinforcement | ~70 | % | Reported comparison with new blades |
| Hardfacing material | T-620 | — | High-carbon, carbide-containing electrode |
| Alternative conventional electrode | T-590 | — | Cited for tillage-tool restoration; not tested in the reported comparison |
| Modifier | Non-magnetic detonation-charge fraction | — | Contains nano- and dispersed diamond material |
| Recommended point-tip stripe | 20 | mm | Applied from the front face of the blade |
| Recommended wing-stripe size | 12-15 | mm | Applied from the rear face of the blade |
| Minimum stripe separation | ≥10 | mm | Intended to prevent overlap of heat-affected zones |
| Carbide-phase increase—surface | 27 | % | Relative to unmodified T-620 surfacing |
| Carbide-phase increase—middle | 32 | % | Relative to unmodified T-620 surfacing |
| Carbide-phase increase—transition zone | 70 | % | Relative to unmodified T-620 surfacing |
| Chromium-distribution improvement | 2.2× | uniformity | Across the three analyzed coating zones |
| Conventional carbon—surface | 2.8 | wt% | XREPA result as reported narratively |
| Conventional carbon—middle | 1.83 | wt% | XREPA result as reported narratively |
| Conventional carbon—transition zone | 1.64 | wt% | XREPA result as reported narratively |
| Conventional oxygen | 1.6-3.39 | wt% | Detected in all analyzed zones |
| Modified oxygen | 2.28 | wt% | Detected only in the upper stripe zone in the modified specimen |
| Modified iron—upper zone | 61.12-64.15 | wt% | XREPA range in Table 2 |
| Modified iron—middle zone | 61.07-68.80 | wt% | XREPA range in Table 2 |
| Modified iron—transition zone | 57.77-86.98 | wt% | XREPA range in Table 2 |
| Modified chromium—surface | 17.05-19.13 | wt% | XREPA range in Table 2 |
| Modified chromium—middle | 15.47-18.58 | wt% | XREPA range in Table 2 |
| Modified chromium—transition | 0.46-23.14 | wt% | Includes substrate-dilution variation |
| Abrasion-test configuration | Disc-block | — | SMT-1 friction machine |
| Abrasive | Quartz sand | — | Staroverovsky deposit, Ukraine |
| Quartz-sand fraction | 0.25-0.4 | mm | Unlubricated abrasive medium |
| Abrasive carrier | PTFE-4 fluoroplastic | — | Used to hold sand in the friction zone |
| Test coupon size | 10 × 10 | mm | Cut from the surfaced zone |
| Surface-grinding load | 5 | kg | Coupon preparation |
| Friction path | 100 | m | Brinell-scheme abrasive test |
| Untreated 65G wear | 0.0145 | g | Test variant 1 |
| Unmodified T-620 wear | 0.0090 | g | Test variant 2 |
| Modified T-620 wear | 0.0044 | g | Test variant 3 |
| Wear reduction versus untreated steel | 69.7 | % | Calculed from the reported test masses |
| Wear reduction versus unmodified T-620 | 51.1 | % | Calculed from the reported test masses |
| Relative wear resistance versus untreated steel | ~3.3× | — | Calculed from 0.0145 g ÷ 0.0044 g |
| Relative wear resistance versus unmodified T-620 | ~2.05× | — | Calculed from 0.0090 g ÷ 0.0044 g |
| Field test population | 81 | blades | Tiger Mate II cultivator |
| Unhardened field population | 66 | blades | Test group |
| Hardened field population | 15 | blades | Modified T-620 process |
| Average field wear improvement | 2.3× | — | Reported field result |
| Published field-life improvement | 2× | — | Authors’ stated comparison with initial condition |
| Published modified-coating improvement | 3× | — | Authors’ stated comparison with nonmodified reinforcement |
Key Methodologies
Section titled “Key Methodologies”-
Map the service damage
- Inspect new and worn cultivator blades at defined measurement points and blade sections.
- Identify the point tip and wings as the principal failure zones.
- Use the observed deformation and wear asymmetry to select the correct face for each overlay.
-
Define localized reinforcement geometry
- Place a 20 mm stripe on the front face of the point tip.
- Place 12-15 mm stripes on the rear face of the wings.
- Maintain at least 10 mm spacing between adjacent heat-affected zones.
-
Prepare the modified hardfacing consumable
- Use a carbide-containing T-620 electrode with a non-magnetic fraction of detonation charge from ammunition disposal.
- Optimize the modifier proportion to control the liquid-bath temperature and crystallization range.
- Rely on the dispersed diamond fraction to suppress coarse solidification structures and provide distributed carbide-forming/nucleating sites.
-
Apply the hardfacing
- Deposit the stripes locally rather than surfacing the entire blade.
- Restrict heat input because the thin-walled 65G substrate has limited heat dissipation and can otherwise melt through or develop cracks.
- Avoid stripe overlap to minimize local thermal stress.
-
Evaluate structure and chemistry
- Examine the surface, middle, and transition regions of the deposited stripe.
- Use X-ray electron-probe analysis to quantify C, O, Al, Si, Cr, Mn, Fe, Zr, and Mo distributions.
- Compare the results with conventional T-620 surfacing to assess carbide refinement, compositional uniformity, and substrate dilution.
-
Measure abrasive wear
- Cut 10 × 10 mm coupons from the surfaced region and surface-grind them using a 5 kg load.
- Test an untreated 65G coupon, an unmodified T-620 coupon, and a modified T-620 coupon.
- Use an SMT-1 disc-block machine, PTFE-4 counterbody, and 0.25-0.4 mm quartz sand over a 100 m path.
-
Validate under field conditions
- Install 66 unhardened and 15 hardened blades on a Tiger Mate II cultivator.
- Compare average wear by blade position.
- Confirm the laboratory trend under abrasive soil-working conditions.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”Recommended Material Strategy
Section titled “Recommended Material Strategy”| Research requirement | Recommended 6CCVD material | Engineering rationale |
|---|---|---|
| Extreme abrasive resistance at thin, wear-critical edges | Polycrystalline diamond, PCD | Distributed diamond crystallites provide a large population of wear-resistant contact points and are better suited than large single-crystal components to edge or insert reinforcement. |
| Crack-resistant, lower-stress reinforcement geometry | Fine-grain PCD or detonation-synthesized diamond-containing PCD | A fine, distributed diamond microstructure is consistent with the paper’s objective of refining coarse carbides, reducing local thermal stress, and limiting defects. |
| Maximum hardness with controlled conductivity | Heavy boron-doped PCD, BDD | Appropriate where abrasive resistance is combined with electrical functionality or charge dissipation; boron content and resistivity should be specified experimentally. |
| Precisely oriented wear edge or optical/electronic test surface | Optical-grade SCD | Preferred only where crystallographic orientation, low defect density, optical quality, or a defined surface is more important than distributed polycrystalline wear performance. |
| Research replication using dispersed diamond modification | MPCVD-grown PCD with controlled diamond particle size and additive distribution | Particle loading, grain size, thickness, and dopant distribution can be evaluated as a controlled alternative to the paper’s mixed secondary-charge modifier. |
- For a direct conceptual extension, fine-grain PCD is the closest 6CCVD analogue to the paper’s nano-/dispersed-diamond-modified hardfacing.
- For the original 65G blade and surfacing experiment, the paper requires a dispersed diamond-containing electrode coating, not a freestanding bulk diamond plate. 6CCVD can provide MPCVD diamond material or diamond-bearing feedstock for controlled additive trials.
- 6CCVD SCD and PCD plates are available from 0.1 to 500 µm, supporting thin wear inserts, coupons, and localized edge-protection architectures.
- PCD plates or wafers can be customized up to 125 mm, subject to the selected grade, geometry, and process specification.
- For instrumentation or electrical contact, BDD is available where boron concentration and sheet resistance must be tailored.
Geometry and Customization Potential
Section titled “Geometry and Customization Potential”| Paper feature | 6CCVD capability | Recommended implementation |
|---|---|---|
| 20 mm point-tip stripe | Custom PCD/SCD strip geometry | Produce a thin, segmented PCD strip or array with rounded or chamfered transitions to reduce stress concentration. |
| 12-15 mm wing stripes | Custom dimensions and laser cutting | Cut inserts to the required width and contour; retain at least 10 mm separation between heat-affected or bonded zones. |
| Thin-wall protection | SCD/PCD down to 0.1 µm | Evaluate graded-thickness inserts or segmented overlays rather than one thick, continuous plate. |
| Distributed hard phases | Fine-grain or heavy boron-doped PCD | Select grain size and dopant level to balance hardness, toughness, conductivity, and thermal-expansion mismatch. |
| Front/rear face placement | Face-specific patterning and orientation | Specify the exposed wear face, edge orientation, edge radius, and allowable bond-line thickness during engineering review. |
| 10 × 10 mm test coupons | Custom SCD/PCD coupon cutting | Prepare matched coupons for disc-block or Brinell-scheme abrasive testing. |
| 81-blade field comparison | Custom insert production runs | Define controls and hardened groups separately to permit statistical comparison. |
- 6CCVD can customize plate dimensions, coupon geometry, edge preparation, and thickness for feasibility studies and full test programs.
- Laser cutting services support complex contours and closely spaced reinforcement segments.
- In-house metalization with Au, Pt, Pd, Ti, W, or Cu permits evaluation of brazed, diffusion-bonded, or metallized diamond-to-steel attachment systems.
- For steel attachment, Ti is a suitable candidate for adhesion/interlayer development, while Pt, Au, or Pd can be evaluated for inert barrier layers; W or Cu may be considered for refractory or thermal-spreading interlayers.
- Bonding trials are required because the paper emphasizes defect control. Diamond, carbide hardfacing, and 65G steel have substantially different thermal expansion and elastic behavior.
Engineering Support
Section titled “Engineering Support”- 6CCVD’s in-house PhD engineering team can assist with material selection for similar abrasive agricultural cutting tools, cultivator blades, and thin-section wear components.
- Recommended development sequence:
- Stage 1—Material screening: Compare fine-grain PCD, SCD, and BDD using matched 10 × 10 mm test coupons.
- Stage 2—Attachment screening: Evaluate Ti, W, Cu, Pt, Pd, or Au metalization schemes for adhesion, thermal mismatch, and shear loading.
- Stage 3—Geometry optimization: Reproduce the paper’s 20 mm and 12-15 mm stripe concept with segment spacing of at least 10 mm.
- Stage 4—Abrasive validation: Use 0.25-0.4 mm quartz sand, PTFE-4 carrier, and a controlled 100 m test path.
- Stage 5—Field validation: Compare treated and untreated blade groups, retaining the paper’s useful combination of bench testing and field exposure.
| Selection factor | SCD | PCD | BDD |
|---|---|---|---|
| Abrasive resistance | Very high | Very high, with multiple wear-resistant grain orientations | Very high, with conductivity control |
| Defect tolerance | Lower than PCD | Higher because grain boundaries can interrupt crack propagation | Grade-dependent |
| Complex contouring | More orientation-sensitive | Well suited | Well suited |
| Electrical behavior | Insulating | Generally insulating, depending on structure and dopants | Conductive/p-type behavior possible |
| Best use in this application | Oriented single-edge test specimens | Primary candidate for segmented blade protection | Candidate where electrical behavior is required |
For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
In recent years, research and developments related to the creation of new areas using nanotechnology take a special place in scientific achievements. They are developed and widely used in Physics, Chemistry, Biology, Electronics, Medicine, Food Production and to a much lesser extent in Engineering. This is due to the fact that there are different requirements to parts and products used in mechanical engineering, they have a complex shape, are made of different materials, production methods, heat treatment. While operating, their working layer undergoes degradation with a significant change in structure and their hardening using nanocoatings may turn out to be ineffective in both technical and economic aspects. In this case, only a specific approach, which is determined by comprehensive research with identification of the main factors of parts damageability in specific production and operation conditions, can be expedient. In addition, in some cases for hardening, repair and restoration of parts it is expedient to use surfacing methods with the introduction of modifying agents in a liquid bath during crystallization. These modifying agents are nano-and dispersed diamonds, which make it possible to adjust temperature parameters of crystallization, grain size, and stress level. This approach allows using high-alloyed, high-carbon electrodes even for thin-walled steel and cast iron products. In this case, the diamond inclusions additive plays the role of micro-refrigerators, which significantly change the crystallization temperature range. It is important to determine the optimal dose of the introduction of such a modifier and ensure uniform distribution the components in the coating. The presented work is devoted to the new technology development of hardening of cultivator blades metal with nano-and dispersed diamond additives, which are the part of the detonation charge from the disposal of ammunition. Nowadays, in agriculture, a large number of tillage implements are used for tillage, the working bodies of which are sweep blades. They are operated under conditions of abrasive particles impact, and this is accompanied by their intense wear with a corresponding change in the geometric dimensions of the main working surfaces. The worn sweep blades significantly reduce efficiency and quality of the carried-out work. The analysis of the effective choice of surfacing materials for hardening and improving their performance has been carried out and the nature of wear has been evaluated in order to identify areas of maximum damage and to determine the optimal method. It is known that T-590 and T-620 electrodes are used for the restoration surfacing of tillage implements. It was found the hardfacing of thin-walled parts is accompanied by a smaller heat sink and, in some cases, they are flooded with defect formation. To reduce it, a non-magnetic fraction of detonation charge from ammunition disposalin the form of an electrode modification was introduced, which ensured the uniform distribution the components in the coating. The method of the X-ray electron-probe analysis has been used to evaluate features of structure formation and component distribution along the perimeter of the coating. It was found out that this method of hardening reduces heat input and increases the microhardness and wear resistance of the surfaced coating, reduces the transition zone and thermal impact. The recommended method of metal hardening of new cultivator blades is to apply stripes on the point tip and wings of blades. On the basis of the nature of wear, the expediency of applying stripes on the point tip of the cultivator blade from the front side, and on wings from the rear side, is justified. The optimal geometrical dimensions of hardening stripes and their location on the blade are presented, which allows minimizing the local stresses and increasing wear resistance.