Skip to content

TEMPERATURE STABILITY OF MATERIALS FOR COMPOSITE MICROWAVE ACOUSTIC RESONATORS AND SENSORS ON DIAMOND SUBSTRATES

MetadataDetails
Publication Date2023-01-01
JournalIZVESTIYA VYSSHIKH UCHEBNYKH ZAVEDENIY KHIMIYA KHIMICHESKAYA TEKHNOLOGIYA
Authors
Citations1
AnalysisFull AI Review Included
  • Core Challenge: Evaluating the thermal stability (up to 650 °C) of High overtone Bulk Acoustic Resonators (HBARs) built on single-crystalline diamond substrates with different electrode metallization schemes.
  • Optimal Stack Identified: The Al/ASN/Mo/(100) diamond multilayer piezoelectric structure (MPS-B) demonstrated full retention of functional acoustic and electromechanical properties at 600 °C and survived a 650 °C × 1 h anneal without structural changes.
  • Failed Stack: The Pt/ASN/Pt/(100) diamond structure (MPS-A) suffered complete degradation at 600 °C due to Pt grain agglomeration and cavitation, contradicting the assumption that Pt is inherently a high-temperature-stable electrode.
  • Electrode Hierarchy: Bare Mo oxidizes rapidly above 400 °C and evaporates by 500 °C; however, when encapsulated beneath an Al1-xScxN (ASN) film, Mo retains functional conductivity up to 600 °C. Al forms a protective σ-Al2O3 layer during anneal.
  • Piezoelectric Stability: Aluminum-Scandium Nitride (ASN, Al0.87Sc0.13N and Al0.75Sc0.25N) remained operational in the Al/ASN/Mo/(100) diamond stack even at 600 °C with no degradation.
  • Application Impact: Validates diamond-based HBARs as reliable sensors and microwave acoustic devices for high-temperature and harsh-environment deployments (aerospace, energy, industrial monitoring).
  • Methodology: Sequential isothermal annealing (300 °C → 650 °C, in 50 °C steps, 1 h dwell each) in ambient air, coupled with microwave acoustic characterization, HR-TEM/SEM, XRD, EDS, and FFT analysis.
ParameterMPS-A (Pt-based)MPS-B (Mo-based)UnitContext
Substrate(100) single-crystal diamond(100) single-crystal diamond—Low-loss microwave acoustic substrate
Substrate Thickness629330µmPolished free-standing plate
Piezoelectric MaterialAl0.87Sc0.13N (ASN)Al0.75Sc0.25N (ASN)—Sc content verified by XRD (c, a lattice params)
Piezoelectric Thickness10131000nmSputter-deposited film
S-Electrode Material / ThicknessPt / 122Al / 114nmTop (signal) electrode
G-Electrode Material / ThicknessPt / 105Mo / 105nmBottom (ground) electrode
Aperture Area10,00010,000µm²Active resonator zone
Al Pad Over MoNoYes (edge protection)—Shielded G-electrode contact pad
Max Operational Frequencyup to 40up to 40GHzPrior HBAR record [Ref 3]
Quality Factor (Q)~10,000~10,000—Baseline before anneal
Film Thickness Sensitivity±0.5 (Pt)—nmSensor resolution [Ref 4]
Anneal Range300 - 600300 - 650°C1 h dwell, air, 50 °C steps
Pt Degradation Threshold400 (cavities); 600 (catastrophic)N/A°CGrain agglomeration
Mo Oxidation Threshold (bare)N/A> 400 (onset); 500 (evaporation)°CExposed to air
Mo Stability (encapsulated)N/Aup to 600°CUnder ASN film
Al Oxide Phase FormedN/Aσ-Al2O3—Confirmed at 650 °C
Composition (Al film, 650 °C)N/A47.3 at.% Al; ~35 at.% Oat.%EDS analysis
Hüttig Temperature (Pt reference)339—°C≈ 0.3 × Tmelt; adatom mobility onset
Pt Melting Point1768—°CReference
  • Substrate Preparation: Free-standing (100) single-crystal diamond plates (330 µm and 629 µm thicknesses) used as the acoustic propagation medium.
  • Bottom Electrode Deposition: G-electrode sputtering — Pt (105 nm) for MPS-A; Mo (105 nm) for MPS-B.
  • Piezoelectric Film Growth: Reactive magnetron sputtering of Al1-xScxN (ASN) targeting ~1000 nm thickness; Sc concentration (13% and 25%) controlled by sputtering power and verified via XRD lattice parameter analysis (Empyrean/PAnalytic, Cu Kα).
  • Top Electrode & Contacts: S-electrode sputtering — Pt (122 nm) for MPS-A; Al (114 nm) for MPS-B. MPS-B additionally received an Al cap layer over the Mo contact pad edge to mitigate oxidation.
  • Sequential Annealing Protocol: Air ambient, sequential isothermal holds — 300, 350, 400, 450, 500, 550, 600, (650) °C × 1 h each; upper bound selected just below the Al melting point.
  • Acoustic Characterization: HBAR resonance tracking across 0.2 - 40 GHz; Q-factor and amplitude monitoring after each anneal step.
  • Structural Analysis: Optical microscopy (Olympus), HR-TEM with FFT, SEM morphology imaging, XRD phase identification, and EDS compositional mapping.
  • Oxidation Pathway Identification: Confirmed σ-Al2O3 cubic phase formation on Al films at 650 °C via TEM/FFT; ruled out presence of additional oxide phases.
Paper Requirement6CCVD Offering
Free-standing (100) single-crystal diamond substratesOptical-grade and electronic-grade SCD plates; thicknesses 0.1 µm - 500 µm; substrates up to 10 mm; custom cuts up to 125 mm (PCD)
Both 330 µm and 629 µm substrate thicknesses evaluatedCustom thickness selection per application; laser cutting and precision polishing (Ra < 1 nm for SCD)
Pt / Mo / Al metallization layers (105 - 122 nm)In-house metallization capabilities: Au, Pt, Pd, Ti, W, Cu; custom stack recipes (e.g., Ti/Pt/Au adhesion-promoter schemes) available on request
Ultralow acoustic loss diamond for HBARs operating 0.2 - 40 GHzHigh-purity SCD with controlled N/B impurity profiles; ideal for low-loss GHz-to-THz acoustic wave propagation
High-temperature sensor and harsh-environment deploymentBoron-doped (BDD) and insulating SCD options for combined acoustic + electrochemical sensing platforms
Piezoelectric thin-film compatibility (ASN, AlN, ZnO)Diamond substrates deliverable with industry-standard epi-ready surfaces for direct AlN/ASN/ZnO sputtering
Research-grade custom prototypingIn-house PhD engineering team; full design consultation from material selection through metallization stack design
  • Optical-Grade SCD (single-crystal diamond): The primary substrate in the paper’s successful MPS-B stack. 6CCVD supplies optical-grade (100) SCD wafers and free-standing plates with sub-nanometer surface finish — directly applicable to HBAR fabrication targeting record operational frequencies up to 40 GHz.
  • Heavy Boron-Doped PCD (BDD): For next-generation sensor platforms combining microwave acoustic readout with electrochemical sensing at elevated temperatures.
  • Polycrystalline Diamond (PCD): Cost-effective alternative for non-critical-orientation bulk acoustic devices or pressure-sensor HBAR variants up to 125 mm.
  • Substrate Geometry: Paper reports both 330 µm and 629 µm diamond thicknesses — 6CCVD routinely delivers SCD and PCD in the full 0.1 µm to 10 mm range, enabling precise acoustic-mode Q optimization for target operating frequencies.
  • Metallization Stacks: All electrode metals used in the study (Pt, Mo, Al) and 6CCVD’s standard library (Ti, W, Au, Pd, Cu) can be deposited in-house — including adhesion-promoter underlayers to mitigate the Pt-on-diamond cavitation and Mo-oxidation failures documented in this paper.
  • Laser Cutting & Patterning: Custom aperture geometries and contact-pad layouts delivered ready for piezoelectric sputtering.
  • Surface Engineering: Sub-nm Ra polishing (SCD) ensures minimal phonon scattering and maximized Q-factor retention after high-temperature cycling.
  • Material Selection Consultation: 6CCVD’s in-house PhD team can advise on the optimal combination of substrate thickness, crystallographic orientation, and metallization stack to push HBAR operational frequencies into the 40+ GHz regime while meeting a target thermal ceiling.
  • Failure-Mode Mitigation: Drawing directly on the paper’s findings, our engineers can recommend encapsulated-Mo or capped-Al electrode schemes pre-qualified for 600 °C service, avoiding the Pt-grain-agglomeration pitfall.
  • Sensor Architecture Co-Design: Support for thickness-sensitivity optimization (±0.5 nm-class, as reported) and harsh-environment packaging.

For custom specifications, metallization stack design, or material consultation for high-temperature diamond-based HBAR and acoustic sensor projects, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

В статье рассмотрено влияние отжига при высоких температурах вплоть до 650 °С на работоспособность композитных СВЧ акустических резонаторов на алмазных подложках со структурами Al/ASN/Mo/(100) алмаз и Pt/ASN/Pt/(100) алмаз. Помимо оптических исследований использовали просвечивающую и растровую микроскопию высокого разрешения, рентгеновский дифракционный анализ, а также изучали изменения функциональных свойств акустических резонаторов на СВЧ, происходящие в результате последовательности отжигов. Исследована деградация Mo, Pt и Al электродов, а также температурная стойкость пьезоэлектрической пленки нитрида алюминия-скандия (ASN). Показано, что пленка Mo на алмазе заметно окисляется при температурах выше 400 °С, а при 500 °С улетучивается. Однако Mo, изолированный от воздействия кислорода воздуха пленкой ASN, сохраняет достаточную для работы композитного СВЧ акустического резонатора проводимость вплоть до 600 °С. Pt электроды в составе акустического резонатора оказались наименее стойкими: при 600 °С происходит полная деградация с образованием крупных каверн как для случая Pt на алмазе, так и при покрытии Pt пленкой ASN. В последнем случае также происходило локальное разрушение пленки ASN. Нитрид алюминия-скандия оказался работоспособным в составе резонатора Al/ASN/Mo/(100) алмаз даже при 600 °С и без изменений выдерживал отжиг 650 °С·1 ч. Применение Al в качестве верхнего электрода на пленке ASN и токоведущих дорожек, напыленных на алмаз, показало, что резонатор на основе структуры “Al/ASN/Mo/(100) алмаз” сохраняет свои функциональные акустические и электромеханические свойства при 600 °С.