Skip to content

A thermo–optical chain-linked model and adaptive cavity-length compensation for high-power diamond Raman lasers

MetadataDetails
Publication Date2026-01-01
JournalHigh Power Laser Science and Engineering
AuthorsFei Zhang, Pengfei Li, Yifu Chen, Hui Chen, Hao Zheng
InstitutionsHebei University of Technology
AnalysisFull AI Review Included
  • Challenge Solved: Mitigates power roll-off and instability in high-power continuous-wave Diamond Raman Lasers (DRLs) caused by thermally induced cavity-mode mismatch, even when using ultra-high thermal conductivity materials.
  • Core Innovation: Establishes a thermo-optical chain-linked model mapping pump power → thermal load → effective thermal lens → cavity-mode overlap → Stokes output.
  • Control Criterion: Introduces a Peak-Valley Co-location (PVC) criterion where maximum output power and minimum RMS fluctuation occur at a single optimal cavity-length offset (ΔL*).
  • Experimental Validation: Increased first-Stokes output from 27 W to 32 W (+18%) and reduced power fluctuation RMS from 4.8% to 3.2% (-33%) at 82 W pump power.
  • Beam Quality Maintained: Near-diffraction-limit operation preserved at the optimal compensation point (Mx2 = 1.18, My2 = 1.19).
  • Engineering Impact: Provides a single-parameter (cavity length) active compensation strategy for stable high-power laser scaling, replacing empirical tuning with a predictable design rule.
  • System Configuration: External-cavity DRL with CW fiber pump at 1064 nm (up to 500 W), Stokes output at 1240 nm (first-order Raman shift of diamond).
ParameterValueUnitContext / Condition
Pump Wavelength (λp)1064nmCW fiber laser source
Maximum Pump Power500WAvailable from source
Operating Pump Power82WAt maximum Stokes output
Stokes Wavelength (λs, 1st order)1240nmFirst-order Raman shift
Threshold Power (1st Stokes)~26WWith fixed cavity length
Uncompensated Stokes Output~27WAt 82 W pump, ΔL = 0
Compensated Stokes Output (Ps)~32WAt ΔL* ≈ 0.37 mm
Optical-to-Optical Efficiency~33%Uncompensated peak output
RMS Fluctuation (Uncompensated)4.8%Over 10-minute window
RMS Fluctuation (Compensated)3.2%At optimal ΔL*
Pump Power RMS~0.2%Intrinsic source stability
Optimal Cavity-Length Offset (ΔL*)~0.37mmPeak-valley co-location point
Beam Quality Factor (Mx2)1.18-After compensation at 82 W
Beam Quality Factor (My2)1.19-After compensation at 82 W
Diamond Crystal Dimensions4 × 2 × 8mmCross-section × length
Pump Waist Radius (wp)~28µmAt crystal center
Stokes Eigen-Waist Radius (cold)44µmIntrinsic cavity mode
Cooling Temperature20°CWater recirculating chiller
Cooling Capacity3000WRecirculating chiller
Coolant Flow Rate10L min-1Through copper holder
Resonator ConfigurationNear-concentric-Total length ~103 mm
Mirror Curvature Radius (R1, R2)50mmIC and OC
OC Transmission @ 1240 nm~0.7%Output coupling
Pump Focusing Lens Focal Length75mmExternal focusing (L1)
  1. Pump Source Preparation: Continuous-wave fiber laser (1064 nm, max 500 W) routed through an optical isolator; half-wave plate aligns polarization with the diamond <111> crystallographic axis to maximize Raman gain.
  2. Diamond Crystal Mounting: Single-crystal diamond (4 mm × 2 mm × 8 mm) wrapped in indium foil and clamped to a water-cooled copper holder (20°C, 10 L min-1, 3000 W chiller); both facets AR-coated for 1064 nm and Stokes wavelengths.
  3. External Cavity Construction: Near-concentric resonator with total length ~103 mm, two 50 mm concave mirrors (IC: HR @ 1240 nm, HT @ 1064/1485 nm; OC: HR @ 1064 nm, HT @ 1485 nm, T ≈ 0.7% @ 1240 nm); intrinsic first-Stokes waist radius ~44 µm.
  4. Pump Focusing: 75 mm focal-length lens delivers ~28 µm waist radius at the crystal center plane.
  5. Thermal-Lens Quantification: Heat load Q calculated from quantum defect and residual absorption; equivalent thermal focal length f derived from thermal conductivity K, beam waist w0, thermo-optic coefficient dn/dT, refractive index n0, Poisson ratio ν, thermal expansion αT, and stress-optic constant Cr,Φ.
  6. ABCD Matrix Modeling: Round-trip propagation matrix formulated with embedded thermal lens and variable right-arm length L2(ΔL); complex q-parameter solved via self-consistency for Stokes eigenmode at crystal center.
  7. Mode-Overlap Calculation: Spatial overlap efficiency ηov(ΔL, f) computed as a function of pump/Stokes waist ratio r = ws/wp; effective Raman gain Geff = G·ηov.
  8. Peak-Valley Co-location (PVC) Criterion: Single-peaked Stokes power Pnorms(ΔL) and U-shaped RMSnorm(ΔL) analytically related via the local slope dPs/dΔL; optimal offset ΔL* identified where the power peak and stability valley coincide.
  9. Experimental Verification: Cavity length scanned in fine increments at fixed pump power (82 W); output power and time-series stability recorded to validate the PVC criterion.
  10. Compensation Sweep: Optimal ΔL* measured across multiple pump-power levels; comparison to theoretical prediction confirms monotonically increasing compensation demand with pump power.
  • Optical-Grade Single Crystal Diamond (SCD): This research requires ultra-high thermal conductivity, low absorption at the pump (1064 nm) and Stokes (1240 nm) wavelengths, and high optical-quality bulk material. 6CCVD’s Optical Grade SCD with sub-nanometer polishing (Ra < 1 nm) and low birefringence is engineered precisely for high-power Raman laser gain media.
  • Custom Crystal Geometries: The paper specifies a 4 mm × 2 mm × 8 mm rectangular prism with strict facet parallelism. 6CCVD routinely delivers SCD in custom aspect ratios and lengths, with AR-coating-compatible surface finishes.
  • High-Purity CVD Plates: Diamond purity directly governs residual absorption and thermal lensing magnitude. 6CCVD’s low-nitrogen, low-impurity plates minimize absorption losses that drive thermal-lens formation.
  • Anti-Reflection Coatings: Both facets of the diamond in this study are AR-coated for 1064 nm and Stokes wavelengths. 6CCVD offers custom dielectric AR coatings tailored to specific pump/Stokes wavelength pairs (1064/1240 nm, 1064/1485 nm, or other Raman shifts).
  • <111> Orientation Control: Polarization alignment to the <111> axis is critical for maximum Raman gain. 6CCVD provides orientation-controlled SCD with verified crystallographic axes and optional pre-aligned crystal mounting fixtures.
  • Thermal Interface Engineering: The indium-foil/copper-holder mounting demonstrated here is one viable approach. 6CCVD’s engineering team can collaborate on metallized diamond heat spreaders (Ti/Pt/Au or Ti/Cu stacks) for enhanced thermal contact in demanding packaging.
  • Dimensional Flexibility: While the paper uses 4 × 2 × 8 mm, 6CCVD can produce SCD/PCD plates and wafers up to 125 mm in diameter and thicknesses from 0.1 µm to 500 µm, enabling scaling of this experiment to larger apertures or alternative resonator geometries.
  • Laser Cutting & Shaping: Custom non-standard crystal cross-sections can be precision-cut via 6CCVD’s laser machining capabilities to match exact experimental requirements.
  • Multiphysics Modeling Assistance: The thermo-optical chain-linked model presented here (pump → heat → thermal lens → mode overlap → power) maps directly onto 6CCVD’s material parameter library (thermal conductivity, dn/dT, absorption coefficient, Raman gain). Our in-house PhD team can supply verified material data to support your own ABCD and thermal simulations.
  • Material Selection for Raman Systems: 6CCVD’s engineering team can advise on optimal diamond grade (SCD vs. PCD), purity level, doping strategy, and coating stack for target wavelengths from UV to mid-IR.
  • Rapid Prototyping: Custom sample delivery for proof-of-concept resonator experiments, with iterative design feedback between your modeling group and our process engineers.
  • Co-Development Partnerships: For teams scaling beyond 82 W pump power toward the kW-class DRL regime, joint development of low-absorption, high-thermal-conductivity diamond gain elements is available.

The cavity-length compensation technique demonstrated in this work is universally applicable wherever thermal lensing limits laser power scaling. To replicate, extend, or commercialize this research, partner with a diamond supplier that controls the entire process chain—from CVD growth through polishing, coating, and metallization.

For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

Abstract Continuous-wave diamond Raman lasers (DRLs) operated at high pump power commonly suffer from power roll-off and output instability, even when high-thermal-conductivity gain media are employed. These degradations originate from thermally induced cavity-mode mismatch and cavity-length drift, which limit further power scaling. In this work, we establish a thermo-optical chain-linked model that quantitatively describes the coupled evolution of thermal deposition, equivalent thermal lensing, intracavity-mode matching and output power in high-power DRLs, providing a direct physical link between pump power and cavity-length compensation. Based on this model, a peak-valley co-location criterion is proposed to determine the optimal cavity-length compensation point. Both theoretical and experimental results show that the output power exhibits a single-peak dependence on cavity-length offset, while the power stability follows a U-shaped distribution, and their extrema coincide at an optimal compensation value ΔL *. By operating at ΔL *, the maximum Stokes output power increases from 27 to 32 W, and the root mean square power fluctuation decreases from 4.8% to 3.2%. These results demonstrate that thermal-lens-induced performance degradation can be effectively mitigated by cavity-length compensation using a single control parameter, providing a practical design rule for simultaneous enhancement of output power and stability in high-power Raman laser systems.