Skip to content

Electrochemical system for simultaneous treatment of textile dyeing effluents and hydrogen recovery

FieldValue
JournalEnvironmental Research
Published2026-01-13
AuthorsDídac Cuesta-Mota, Anna Serra, Jorge Macanás, Lluc Canals-Casals, Víctor López-Grimau
DOI10.1016/j.envres.2026.123713
Citations2

At 150 mA/cm², a membrane-separated reactor decolorized real Procion Blue H-EXL dye-bath effluent while producing hydrogen at 98.7% purity. Selected configurations achieved 94.3 to 96.9% Faradaic efficiency. The bicompartment design consumed 4.7 to 14.5 Wh/L, versus 10.1 to 28.3 Wh/L in the single-compartment test.

The reactor kept wastewater and alkaline catholyte in separate circuits while allowing hydroxide ions to cross a Fumasep FAS-30 anion-exchange membrane. Each electrode exposed 10 cm² of active area. Two 500 mL loops circulated anolyte and catholyte at 250 mL/min, and both remained at 25°C. The catholyte was 20% w/w NaOH, equivalent to 25% w/v. Its conductivity was about 400 mS/cm, compared with about 100 mS/cm in the wastewater.

Hydrogen left the closed catholyte vessel through a moisture trap and a flowmeter recording every 0.5 s. Micro-gas chromatography determined the gas composition.

The wastewater came from dyeing 400 g of cotton knitted fabric for 50 minutes at 60°C. The dye bath contained 3 g/L Procion Blue H-EXL and 80 g/L NaCl or Na2SO4. It used either 20 g/L Na2CO3 or 0.5 mL/L of 50% w/v NaOH. The recovered effluent represented about 75% of the initial 4 L dyebath volume. Initial residual dye ranged from 0.31 to 0.47 g/L, conductivity from 67.0 to 107.9 mS/cm, and pH from 9.8 to 10.6.

Discoloration was measured by UV-visible absorbance at each effluent’s maximum wavelength, 591 to 617 nm. The procedure followed ISO 7887:2011 Method B with wavelength modifications. Duplicate absorbance readings had coefficients of variation below 0.7%. Total organic carbon was measured separately, and treatment continued until 99% discoloration. Kinetic constants were fitted over the first 95% degradation.

A current density of 150 mA/cm² gave the best balance between treatment time and energy. The authors tested 100, 150, and 300 mA/cm² with chloride wastewater. At 300 mA/cm², energy use doubled relative to 150 mA/cm². Treatment time fell only 12% with Na2CO3 and 35% with NaOH. At 100 mA/cm², the reported energy efficiency was about 15% and 6% higher than at 150 mA/cm², with Na2CO3 and NaOH, respectively. Treatment time increased 42% and 60%, respectively.

At 150 mA/cm², NaOH required 1.3 to 1.6 Ah/g dye for 95% discoloration. Na2CO3 required 4.6 to 6.8 Ah/g. Reaching 99% required 1.9 to 2.5 Ah/g with NaOH and 10.7 to 19.9 Ah/g with Na2CO3. With the Pt/Pt screening pair, the pseudo-first-order rate constant was 3.6 × 10⁻³ s⁻¹ with NaOH and 1.7 × 10⁻³ s⁻¹ with Na2CO3. The corresponding R² values were 0.99 and 0.98.

The authors attribute the carbonate penalty to radical scavenging and formation of less reactive carbonate radicals. Chloride treatment produced no substantial TOC change. Hypochlorite removed the chromophore quickly but did not achieve mineralization during the test.

Electrode selection for chloride wastewater

Section titled “Electrode selection for chloride wastewater”

Equal weighting of time, energy, and material cost selected Ir-Ru/Ni through a simplified Analytic Hierarchy Process. With Na2CO3, replacing a Pt anode with Ir-Ru reduced treatment time 23% and energy 30% against Pt/Pt. Ir-Ru/Ni retained reductions of 17% in time and 20% in energy. With NaOH, differences between combinations reached only 8% in time and 14% in energy. The reported price was €375 for Pt and €260 for Ir-Ru.

Nickel cathodes gave 91 to 94% Faradaic efficiency, versus 92 to 96% for platinum. The selected Ir-Ru/Ni combination stayed within 3% of the best Pt/Pt efficiency. Electrode choice changed the kinetic constant far less than alkali choice. Average constants at 150 mA/cm² were 3.4 × 10⁻³ s⁻¹ for NaOH and 1.7 × 10⁻³ s⁻¹ for Na2CO3.

Sulfate wastewater and boron-doped diamond

Section titled “Sulfate wastewater and boron-doped diamond”

BDD/Ni at 150 mA/cm² was selected for sulfate wastewater. The absence of chloride prevented chloride-based anodes from producing hypochlorite. The BDD anode generated hydroxyl radicals, which oxidize dye and its secondary products more broadly than hypochlorite. With NaOH, 95% discoloration required 2.3 Ah/g dye and 99% required 4.1 Ah/g. Na2CO3 required about five times more charge.

The pseudo-first-order constants were 2.7 × 10⁻³ s⁻¹ with NaOH and 0.5 × 10⁻³ s⁻¹ with Na2CO3. Their R² values were 0.99 and 1.00. The carbonate constant was about 70% below the chloride-system values. TOC removal reached about 10% with NaOH and 40% with Na2CO3. By comparison, chloride treatment produced no measurable mineralization. Available BDD electrodes could not work at the approximately 80 g/L NaCl concentration. The authors therefore limited BDD use to sulfate wastewater.

Hydrogen purity averaged 98.7% across all experiments, with a coefficient of variation of 0.25%. The remaining 2% was attributed to atmospheric air in the vessel headspace. Hydrogen flow stayed stable, with coefficients of variation below 2% in every test. Selected configurations produced 94.3 to 96.9% Faradaic efficiency.

Energy recovery potential was about 33% for chloride effluent and 23.4 to 24.7% for sulfate effluent. These figures omit conversion losses from hydrogen use. A 90% efficient water boiler would recover 23.4 to 29.9% of treatment energy. A 45% efficient fuel cell would recover 11.7 to 14.9%.

The AEM configuration also improved energy use against the earlier Hoffmann voltameter. The new cell operated at 4 to 6 V, while the earlier system needed at least 12 V. The earlier system required 14 to 15 Wh/L, compared with 5 to 7 Wh/L in the new cell. Energy recovery potential rose from below 10% to 26 to 33%. The higher catholyte conductivity supported this reduction in voltage.

All selected combinations removed visible color at a 1:20 dilution. The treated water still failed most discharge criteria. TOC ranged from 519.3 to 856.8 mg/L, above the stated limit below 500 mg/L. Conductivity ranged from 67.3 to 108.0 mS/cm, against a limit below 6 mS/cm. Salt remained 74.8 to 83.1 g/L, far above the cited NaCl and Na2SO4 limits. Final pH was 9.2 to 10.1, so color and sometimes pH met the stated limits.

The results therefore support decolorization for reuse rather than complete compliance for direct discharge. Carbonate buffered the wastewater and retained a higher final pH. Hydroxide wastewater fell to pH 9.4 to 10.0 and would require adjustment to pH 11 for reuse.

Table 11 put treatment cost at €0.69/m³ for NaCl with NaOH and €8.56/m³ for Na2SO4 with Na2CO3. Conventional coagulation and flocculation cost €1.66/m³ in the same estimate. Hydrogen recovery saved €0.08 to €0.10/m³ for NaCl with NaOH. It did not make sulfate-carbonate treatment competitive.

The experiments used 500 mL batches. The authors call for a semi-industrial prototype to verify discoloration, hydrogen output, costs, and environmental impacts.

The sulfate treatment used a boron-doped diamond anode with a 10 cm² active area. 6CCVD’s diamond materials catalog lists boron-doped diamond, matching the specified anode material. BDD substrate dimensions and metallization remain unspecified, which the linked engineering support page can address during semi-industrial design.

View Original Abstract

The textile industry is a major contributor to global water pollution, generating complex wastewater that conventional treatments struggle to remediate. Electrochemical processes are effective alternatives, degrading persistent organic pollutants while simultaneously producing hydrogen as a valuable byproduct. However, current electrochemical systems often disregard hydrogen recovery and face challenges such as low wastewater conductivity, high energy consumption, and gas contamination. This study presents a novel bicompartmental electrochemical reactor designed for simultaneous textile dye wastewater treatment and hydrogen recovery. The system incorporates an anion-exchange membrane (AEM) to fully separate the anolyte and catholyte, preventing gas cross-contamination and improving energy efficiency. Key parameters, including current density, electrode materials, and dyeing auxiliaries are systematically evaluated in this study. This electrochemical system effectively decolorizes real textile wastewater, being the dye (Procion Blue H-EXL) degraded following a pseudo-first-order kinetics. Optimal conditions for industrial application are identified using a multicriteria approach, selecting Ir-Ru/MMO as the anode and Ni as the cathode at 150 mA/cm 2 for treating dye textile effluents that use NaCl as a salt. For dye wastewaters containing Na 2 SO 4 instead of NaCl, a BDD anode is chosen to generate hydroxyl radical for effective treatment and Ni is also selected as the cathode. The applied charge required for 95 % dye degradation ranges from 1.7 to 12.3 Ah/g dye depending on the salt and alkali used in the dye process, with the kinetics with NaOH being from two to five times faster than with Na 2 CO 3 . Additionally, the system achieves stable hydrogen production with high Faradaic efficiency (94.3-96.9 %) and purity (98.7 %), with an energy recovery potential of 23-33 % relative to the treatment energy consumption. This scalable and efficient electrochemical system offers a promising solution for industrial textile wastewater treatment while enabling sustainable hydrogen production.

  1. 2021 - Performance of electrochemical oxidation over bdd anode for the treatment of different industrial dye-containing wastewater effluents [Crossref]
  2. 2022 - Water quality. Determination of total organic carbon (TOC), dissolved organic carbon (DOC), total bound nitrogen (TNb) and dissolved bound nitrogen (DNb) after high temperature catalytic oxidative combustion (ISO 20236:2018)
  3. 2006 - Natural gas. Determination of composition and associated uncertainty by gas chromatography. Part 6: determination of hydrogen, helium, oxygen, nitrogen, carbon dioxide and C1 to C8 hydrocarbons using three capillary columns (ISO 6974-6:2002)
  4. 1999 - Advanced oxidation processes (AOP) for water purification and recovery [Crossref]
  5. 2012 - Electrochemical oxidation of textile polluted water and its reuse
  6. 2022 - Advances, opportunities, and challenges of hydrogen and oxygen production from seawater electrolysis: an electrocatalysis perspective
  7. 2021 - A comparative review on clean hydrogen production from wastewaters [Crossref]
  8. 2022 - Textile effluent treatment methods and eco-friendly resolution of textile wastewater [Crossref]
  9. 2023 - Demand response approaches in a research project versus a real business [Crossref]