Optimization of 3D diamond detectors with graphitized electrodes based on an innovative numerical simulation.
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2026-01-01 |
| Journal | Journal of Instrumentation |
| Authors | L. Anderlini, Alessandro Bombini, Clarissa Buti, D. Janssens, S. Lagomarsino |
| Institutions | University of Florence, University of Urbino |
| Analysis | Full AI Review Included |
Technical Brief: Optimization of 3D Diamond Detectors with Graphitized Electrodes Based on an Innovative Numerical Simulation
Section titled “Technical Brief: Optimization of 3D Diamond Detectors with Graphitized Electrodes Based on an Innovative Numerical Simulation”> Source: JINST (CERN/INFN Firenze collaboration, TimeSPOT) > Focus: 3D SCD pixel detectors, laser-induced graphitization, signal propagation, time resolution
Executive Summary
Section titled “Executive Summary”- Material Platform Validation: Confirms single-crystal diamond (SCD) as the leading solid-state sensor for high-radiation, high-flux hadron collider environments (HL-LHC, FCC-hh, Muon Collider) owing to its wide bandgap, high carrier mobility, and saturation velocity.
- Geometry Tested: 3D architecture with 12 µm-diameter, 450 µm-long laser-graphitized through-columns on a 55 × 55 µm2 pixel pitch within a 500 µm-thick SCD bulk.
- Primary Performance Limiter: The high resistivity of bulk graphitized columns (measured ~30 kΩ/column, corresponding to 0.75 Ω·cm) dominates time resolution, manifesting as RC delay during signal propagation through the electrodes.
- Numerical Innovation: Extended Ramo-Shockley theorem solved via a custom JAX-based pseudo-spectral solver (Method C), cross-validated against COMSOL FEM (Method B) and a discrete impedance ladder (Method A), then benchmarked against 2021 CERN SPS pion beam-test data.
- Key Benchmark: Simulated time resolution 71 ± 4 ps; experimental 82 ± 2 ps (Crystal Ball Gaussian core, amplitude threshold > 60 mV).
- Design Trade-off Identified: Unlike trench-type Si 3D sensors, resistive graphitic diamond columns deteriorate with tilt angle: a 5° tilt degrades resolution from 65 ps to 96 ps due to depth-dependent propagation delay variances.
- Optimization Roadmap: Reducing resistivity below 0.3 Ω·cm (or electrode resistance < 10 kΩ) is mandatory before geometric refinements become impactful; tilted parallel-column geometry provides modest benefit for field uniformity without penalty.
- Theoretical Floor: Pure jitter + field-inhomogeneity floor estimated at ~15 ps for this electrode geometry with the given readout electronics.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Test Particle | 180 GeV/c | π+ | CERN SPS H6 beam line, 2021 test |
| Charge Deposit (per event) | ~15,000 | e− | Primary electrons over track length |
| Diamond Bulk Thickness | 500 | µm | SCD, electronic grade |
| Pixel Pitch | 55 × 55 | µm2 | Square cell, central readout, 4-corner bias |
| Electrode Diameter | ~12 | µm | Cylindrical graphitized column |
| Electrode Length | 450 | µm | Through-column, opposite-face entry |
| Bias Cell Geometry | 3-corner bias, 1-center readout | - | 6 × 6 pixel prototype matrix |
| Electrode Resistance | 30 ± (large) | kΩ | Indirect measurement; reference through-column |
| Graphitic Resistivity | 0.75 | Ω·cm | Volume resistivity of graphitized phase |
| Relative Permittivity (εr) | 5.7 | - | Standard diamond dielectric |
| Elementary Cell Capacitance | 10 - 100 | fF | Numerical + measurement range |
| Simulated Time Resolution (Resistive) | 71 ± 4 | ps | Method C, 0.75 Ω·cm, default geometry |
| Experimental Time Resolution | 82 ± 2 | ps | Beam test, >60 mV amplitude cut |
| Simulated Time Resolution (Metallic) | 28 ± 3 | ps | Field-inhomogeneity-only floor |
| Trench Geometry Resolution | 50 ± 3 | ps | Best theoretical configuration; fabrication unlikely |
| Most Probable Sim. Amplitude | 101.7 ± 0.6 | mV | Landau peak, 30 kΩ simulated |
| Most Probable Exp. Amplitude | 89.7 ± 0.4 | mV | Landau peak, beam-test measurement |
| Electronic Noise (σv) | 5 | mV RMS | KU board baseline |
| MCP-PMT Reference Resolution | <10 | ps | External trigger timing |
| DSO Sampling Rate | 20 | GS/s | 6 GHz analog bandwidth |
| Tilt Angle Degradation (0° → 5°) | 65 → 96 | ps | Sharp penalty due to resistive columns |
| Asymptotic Resistance Threshold | ~10 | kΩ | Below this, resistance contribution sub-dominates |
| Target Resistivity for Geometry Optimization | ≤0.3 | Ω·cm | Where field uniformity & jitter dominate |
Key Methodologies
Section titled “Key Methodologies”Sensor Geometry & Fabrication
Section titled “Sensor Geometry & Fabrication”- Substrate: Single-crystal CVD diamond, 500 µm thick, prepared for graphitization.
- Electrode Patterning: Femtosecond pulsed-laser graphitization forming cylindrical graphitic columns, ~12 µm diameter, extending 450 µm through the bulk from opposite faces.
- Surface Routing: Comb-like, parallel graphitic traces grouping 6 × 1 pixel strips to enlarge the active area.
Computational Workflow (Four-Stage Pipeline)
Section titled “Computational Workflow (Four-Stage Pipeline)”- Stage 1 — Charge Generation (Garfield++ + Heed): Stochastic ionization along pion tracks modeled via Landau-distributed cluster energies.
- Stage 2 — Carrier Transport (Garfield++): Drift trajectories computed in three coordinate maps from the Poisson equation, ignoring drift inside conductive graphitic volumes:
- v(t) = µ·E(x(t)) up to vs.
- Stage 3 — Signal Propagation: Time-dependent weighting potentials Ψ(x, t) solved three ways:
- Method A: Discrete R-C impedance ladder (Ngspice), heuristic.
- Method B: FEM in COMSOL MultiPhysics® (Backward Differentiation Formula, sub-femtosecond risetime ramp).
- Method C: Pseudo-spectral JAX-based solver on uniform voxels with FFT-driven Poisson solver + “voltage pin” boundary enforcement.
- Stage 4 — Readout Convolution: Simulated induced current convolved with KU board Si-Ge amplifier transfer function (two-stage common-emitter), empirically summed measured oscilloscope noise, sampled at 20 GS/s.
Tilt Angle Study Protocol
Section titled “Tilt Angle Study Protocol”Single-pixel geometry with bounded inclined pion tracks traversing both high- and low-field regions at varying depths to isolate propagation-delay variance.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”The sensor architecture in this work is, at its core, a high-purity SCD platform with laser-fabricated graphitic through-electrodes. The dominant performance barrier is column resistance, which depends critically on bulk SCD quality and graphitization uniformity. 6CCVD’s manufacturing lineage directly addresses both bottlenecks.
Applicable Materials
Section titled “Applicable Materials”| Sensor Requirement | 6CCVD Recommended Product | Why It Fits |
|---|---|---|
| 500 µm-thick SCD bulk with low trapping | Optical-grade Single Crystal Diamond (SCD) wafers, 0.1 µm - 500 µm thickness, polished to Ra < 1 nm | Minimizes bulk defect density; high charge-collection distance (CCD) preserves prompt amplitude. |
| High thermal/structural resilience under femtosecond laser writing | High-pressure-high-temperature (HPHT) or CVD SCD blanks, controlled strain fields | Resists graphitization-induced micro-cracking by maintaining lattice uniformity. |
| Optional radiation-hard alternative | Boron-Doped Diamond (BDD) as a back-contact or charge-multiplication layer | Provides bulk conductivity if a planar bias option is desired for hybrid designs. |
Customization Potential
Section titled “Customization Potential”- Geometry Replication: 6CCVD’s flexible MPCVD reactors grow SCD plates up to 125 mm (PCD) with thicknesses up to 10 mm — substantial enough to process into custom 500 µm detector substrates with optimized crystallographic orientation for laser-written electrodes.
- Precision Thickness Control: With the time-resolution floor for metallic columns estimated at 15 ps and the as-fabricated bar around 70-80 ps, every micrometer of bulk uniformity matters. 6CCVD’s in-house thickness control supports fine-tuning between signal amplitude (favoring thicker diamonds, more charge) and field uniformity (favoring thinner detectors).
- Custom Metalization & Laser Cutting: Although the present work uses all-carbon graphitic electrodes, hybrid designs often call for transition metallization. 6CCVD’s internal metalization stack offerings (Au, Pt, Pd, Ti, W, Cu) and laser-cutting services can produce lift-ready dies for bonding to front-end ASICs or test boards.
- Surface Polishing: With polishing grades Ra < 1 nm for SCD and < 5 nm for inch-scale PCD, finished surfaces are suitable for bonding or direct lithographic patterning of surface routing traces.
Engineering Support
Section titled “Engineering Support”6CCVD’s in-house PhD engineering team routinely supports HEP detector groups, dosimetry consortia, and timing-layer R&D programs with material selection counseling, and can assist in specifying:
- Optimal substrate dimensions for strip/pixel matrices.
- Resistivity/CCD tradeoff modeling for a given bias and readout noise budget.
- Coordination with femtosecond-laser partners on graphitization recipes tuned to the supplied diamond grade.
Call to Action
Section titled “Call to Action”For custom detector-grade SCD substrates, consultation on bulk thickness, polishing class, or metallization stack design, visit 6ccvd.com or contact the 6CCVD engineering team directly.
View Original Abstract
Abstract Future experiments at hadron colliders require an evolution of the tracking sensors to ensure sufficient radiation hardness as well as space and time resolution to handle unprecedented particle fluxes. 3D diamond sensors with laser-graphitized electrodes are promising candidates due to their strong binding energy, small atomic number, and high carrier mobility. However, the high resistance of the engraved electrodes delays the propagation of the induced signals towards the readout electronics, thereby degrading the precision of the timing measurements. So far, this effect has been the dominant factor limiting the time resolution of these devices, with other contributions, such as those due to electric field inhomogeneities or electronic noise, typically neglected. Recent advancements in graphitization technology, however, motivate a renewed effort in modeling signal generation in 3D diamond detectors, to achieve more reliable predictions. To this purpose, we apply an extended version of the Ramo-Shockley theorem, describing the effect of signal propagation as a time-dependent weighting potential, obtained by numerically solving the Maxwell’s equations in a quasi-static approximation. We developed a custom spectral method solver and validated it against COMSOL MultiPhysics<sup>®</sup> . The response of the modeled sensor to a beam of particles is then simulated using Garfield++ and is compared to the data acquired in a beam test carried on in 2021 by the TimeSPOT Collaboration at the SPS, at CERN. Based on the results obtained with this simulation workflow, we conclude that reducing the resistivity of the graphitic columns remains the priority for significantly improving the time resolution of 3D diamond detectors. Once achieved, optimization of the detector geometry and readout electronics design will become equally important steps to further enhance the timing performance of these devices.
Tech Support
Section titled “Tech Support”Original Source
Section titled “Original Source”References
Section titled “References”- 2012 - 3D silicon sensors: Design, large area production and quality assurance for the ATLAS IBL pixel detector upgrade [Crossref]
- 2019 - First Results on 3D Pixel Sensors Interconnected to the RD53A Readout Chip after Irradiation to 1× 10^16neq cm^-2 [Crossref]
- 2016 - Development of a new generation of 3D pixel sensors for HL-LHC [Crossref]
- 2016 - The INFN-FBK “Phase-2” R D; program [Crossref]
- 2021 - Framework TDR for the LHCb Upgrade II: Opportunities in flavour physics, and beyond, in the HL-LHC era
- 2019 - FCC-hh: The Hadron Collider: Future Circular Collider Conceptual Design Report Volume 3 [Crossref]
- 2024 - Interim report for the International Muon Collider Collaboration (IMCC) [Crossref]
- 2023 - Development of 3D Diamond Detectors for Particle Physics and Dosimetry
- 2021 - Diamond Detectors for Radiotherapy X-Ray Small Beam Dosimetry [Crossref]