Paired production of formic acid/formate by cathodic reduction of CO2 at Sn and anodic oxidation of methanol at BDD
Paper details
Section titled “Paper details”| Field | Value |
|---|---|
| Journal | Electrochimica Acta |
| Published | 2026-02-18 |
| Authors | Paola Meli, Alessandro Galia, Abdirisak Ahmed Isse, Roberta Panepinto, Federica Proietto |
| DOI | 10.1016/j.electacta.2026.148491 |
| Citations | 2 |
Paired electrosynthesis produced formic acid/formate with a tin cathode and a boron-doped diamond anode. The highest reported anodic faradic efficiency was about 90% at 6 °C with 0.5 M NaOH and 0.5 M methanol. A separate sulfate series gave 82% cathodic faradic efficiency at 2 °C in 0.1 M Na₂SO₄ with 0.1 M methanol in both compartments. The selected cell configuration kept total productivity near 2 × 10⁻² mol m⁻² C⁻¹ through 1600 C.
Paired cell and product measurement
Section titled “Paired cell and product measurement”The reactor used two glass chambers separated by a Nafion 324 cation-exchange membrane. Each chamber held 75 mL electrolyte and a 37 mL headspace. The anode was a BDD plate, and the cathode was a tin sheet. Both electrodes had a geometric area of 2.4 cm². The catholyte was continuously saturated with 99.999% CO₂.
Most galvanostatic electrolyses ran for 2 h at 11 mA cm⁻² without stirring. Each condition was replicated at least twice, and the paper reports the average.
CO₂ reduction uses two electrons per formic acid molecule, whereas methanol oxidation uses four. CO and H₂ were cathodic byproducts. Anodic byproducts included CO, CO₂, and O₂.
Liquid formic acid was measured by HPLC at 20 °C and 210 nm. Formic acid showed an approximately 18.5 min retention time. The mobile phase was 0.005 N H₂SO₄ at 0.5 mL min⁻¹. Gas chromatography measured CO and CO₂ every 30 min. Faradic efficiency used measured concentration, charge, volume, Faraday’s constant, and the appropriate electron count.
Supporting electrolyte separates the two optima
Section titled “Supporting electrolyte separates the two optima”Electrolyte identity changed the two reactions in different ways. Each comparison used 0.1 M electrolyte in both chambers and 0.5 M methanol in the anolyte. Electrolyses lasted 2 h at 11 mA cm⁻².
| Supporting electrolyte | Cathodic faradic efficiency | Anodic faradic efficiency |
|---|---|---|
| K₂SO₄ | 66% | 35% |
| Na₂SO₄ | 72% | 32% |
| KOH | 49% | 34% |
| Cs₂SO₄ | 70% | 27% |
| KHCO₃ | 67% | 18% |
Na₂SO₄ gave the highest cathodic faradic efficiency at 72%. Cs₂SO₄ and K₂SO₄ gave 70% and 66%. KOH gave 49% cathodic efficiency, with the catholyte remaining near neutral after absorbing CO₂. OH⁻ and sulfate gave higher anodic efficiency than bicarbonate.
The Na₂SO₄ anolyte fell from pH 6.5 to 2.0. The KOH anolyte moved from pH 13.2 to 12.6. KHCO₃ held both compartments near neutral. Na⁺ slightly improved cathodic efficiency relative to K⁺. Cs⁺ gave the lowest anodic efficiency among the three sulfates. Alkali cation effects were small compared with anion and pH effects.
Increasing NaOH from 0.1 to 0.5 M raised anodic faradic efficiency from 40% to 84%. After 2 h, anodic formic acid rose from 2.8 to 6.0 mM. NaOH gave higher anodic efficiency than KOH at both tested concentrations. Increasing NaOH reduced cathodic formic acid production.
The selected pair used 0.1 M Na₂SO₄ catholyte and 0.5 M NaOH anolyte. The anolyte also contained 0.5 M methanol.
Potential and methanol concentration
Section titled “Potential and methanol concentration”Cyclic voltammetry used a 0.1 cm² BDD electrode at 0.1 V s⁻¹. The potential range was 0 to 2.0 V versus SCE. In 0.1 M Na₂SO₄, water oxidation began above 1.8 V versus SCE. Adding 5, 50, or 500 mM methanol increased current in the water-decomposition region.
The authors associate this response with adsorbed or homogeneous hydroxyl radicals. In KOH, methanol adsorption and direct oxidation may compete with water oxidation. These are proposed interpretations, not a confirmed mechanism.
Preliminary potentiostatic trials used 0.5 M methanol for 2 h. At 2.0 V versus SCE in Na₂SO₄, anodic formic acid efficiency was 28 to 32%. CO₂ accounted for 16 to 20% efficiency, and CO accounted for 3 to 5%. The current density fell from 6 to 4 mA cm⁻² during that trial.
At 1.25 V versus SCE in KOH, formic acid efficiency reached 58 to 62%. However, current density remained below 1 mA cm⁻². This tradeoff limited performance at the lower potential.
In 0.5 M NaOH, raising methanol from 0.05 to 0.5 M increased anodic efficiency from 51% to 83%. Raising methanol to 1 M reduced efficiency slightly to 81%. In 0.1 M Na₂SO₄ anolyte, 0.05 and 0.1 M methanol each gave about 50% efficiency. At 1 M methanol, anodic efficiency fell to about 25%. Methanol did not reduce cathodic performance, which stayed near 70% efficiency.
Temperature controls the cathodic yield
Section titled “Temperature controls the cathodic yield”With 0.1 M Na₂SO₄ and 0.1 M methanol in both compartments, cathodic efficiency rose as temperature fell. Efficiency increased from 53% at 35 °C to 82% at 2 °C. Cathodic formic acid rose from 7.3 to 11.5 mM over that interval.
Anodic sulfate efficiency peaked near 53% at 6 °C. Anodic formic acid was 2.8 mM at both 35 and 2 °C. With 0.5 M NaOH and 0.5 M methanol, anodic efficiency was about 85% at 24 °C and 90% at 6 °C. The temperature effect was small in this alkaline anolyte.
An earlier tin study in the paper reported its best result at 3 °C. The present cathodic trend agrees in direction with that study. An earlier CuO-on-copper-foam study reported better methanol oxidation at higher temperature. Those comparisons used different anodes and electrolytes, so they do not isolate temperature alone.
Productivity under extended charge
Section titled “Productivity under extended charge”Longer runs used 0.1 M Na₂SO₄ in the catholyte and 0.5 M NaOH with 0.5 M methanol in the anolyte. Current density was 22 mA cm⁻² at 23 °C.
Formic acid concentration increased almost linearly with charge in both compartments. Anodic productivity stayed near 8.6 × 10⁻³ mol m⁻² C⁻¹, with efficiency close to 70%. Cathodic productivity stayed near 1.2 × 10⁻² mol m⁻² C⁻¹. Cathodic formic acid formation requires fewer electrons, which explains its higher productivity per charge. Total cell productivity remained near 2 × 10⁻² mol m⁻² C⁻¹.
Stability was good over the tested duration, but no long-term electrode or membrane lifetime was reported.
Scale-up limits and engineering implications
Section titled “Scale-up limits and engineering implications”The reactor was a divided glass cell operated without mechanical stirring. The longest test passed 1600 C, but no continuous-feed operation was reported.
The authors report higher efficiency than Pt anodes discussed in the literature, but provide no matched numerical comparison. They request a direct comparison of BDD with conventional anodes under matched conditions. They also identify flow cells, gas diffusion cathodes, pressurized systems, undivided cells, and economic analysis as required studies.
The paired design uses methanol oxidation instead of oxygen evolution at the anode. The introduction cites cases where oxygen evolution consumed more than 90% of total electrical input. The authors report BDD operation in neutral and basic media, while cited Ni nanoparticle anodes were limited to basic conditions. Electrolysis in sulfate anolyte also generated oxygen through water oxidation.
These results support BDD for methanol oxidation in neutral or alkaline paired cells, while retaining Sn for cathodic CO₂ conversion. Application scale remains unresolved until flow, pressure, undivided-cell, and economic studies are complete.
Materials and support
Section titled “Materials and support”The paper’s material requirement is a plate-form BDD anode with a 2.4 cm² geometric area for methanol oxidation. 6CCVD’s diamond materials catalog includes boron-doped diamond plates and wafers up to 125 mm. The linked engineering support service covers custom fabrication for that electrode format.
View Original Abstract
The paired synthesis of formic acid/formate (FA) via CO 2 cathodic reduction and methanol anodic oxidation was investigated using a tin cathode and, for the first time, a boron doped diamond (BDD) anode. To select the most suitable operative conditions for the paired process, the influence of several parameters, such as the nature of the supporting electrolyte (SE), the concentration of both SE and CH 3 OH, and the temperature, was studied in detail for both cathodic and anodic processes. In particular, the effect of SE nature was thoroughly evaluated by testing SEs containing different cations (K + , Na + and Cs + ) and anions (SO 4 2 ⁻, OH⁻, and HCO 3 ⁻). The results show that the use of a BDD anode and of a tin cathode allows to obtain very high faradic efficiencies for both cathodic and anodic processes under optimized operating conditions, especially when operating with 0.1 M Na 2 SO 4 as SE in the catholyte and 0.5 M NaOH + 0.5 M CH 3 OH in the anolyte.
Boron Doped Diamond On Titanium Bdd Electrode
View Specs →
Boron Doped Diamond Electrode On Niobium Bdd Nb Electrode
View Specs →
Boron Doped Single Crystal Diamond Plate
View Specs →Original source
Section titled “Original source”References
Section titled “References”- 2018 - General techno-economic analysis of CO2 electrolysis systems [Crossref]
- 2021 - Electrochemical conversion of CO2 to formic acid using a Sn based electrode: a critical review on the state-of-the-art technologies and their potential [Crossref]
- 2021 - The economic outlook for converting CO2 and electrons to molecules [Crossref]
- 2021 - Towards the electrochemical conversion of CO2 to formic acid at an applicative scale: technical and economic analysis of most promising routes [Crossref]
- 2019 - General technoeconomic analysis for electrochemical coproduction coupling carbon dioxide reduction with organic oxidation [Crossref]
- 2022 - Research targets for upcycling of CO2 to formate and carbon monoxide with paired electrolysis
- 2025 - Ampere-level co-electrosynthesis of formate from CO2 reduction paired with formaldehyde dehydrogenation reactions [Crossref]
- 2017 - Development of an electrochemical process for the simultaneous treatment of wastewater and the conversion of carbon dioxide to higher value products [Crossref]
- 2025 - Coupling Ni-based anodes for textile industry process stream electrooxidation with electrocatalytic CO2 reduction to formate in gas phase [Crossref]
- 2019 - Co-electrolysis of CO2 and glycerol as a pathway to carbon chemicals with improved technoeconomics due to low electricity consumption [Crossref]