BDD/PPy Composites with Low Interfacial Resistance for Energy Storage and Theoretical Feasibility for Pollutant Sensing
Paper details
Section titled “Paper details”| Field | Value |
|---|---|
| Journal | Nanomaterials |
| Published | 2026-06-16 |
| Authors | Shuhan Wang, Yukun Ren, Qinghai Yu, Jie Yang, Jiali Lin |
| DOI | 10.3390/nano16120755 |
BDD/PPy-12 h produced an areal capacitance of 398.6 ± 15.2 mF/cm² at 1 mA/cm² and a fitted charge transfer resistance of 1.3 ± 0.1 Ω. The capacitance was 5.8 times the authors’ value for porous BDD alone, 67.9 mF/cm². Twelve hours was the best polymerization time among 8, 12, 16, and 20 h. The composite combined a porous BDD layer on titanium foam with a conformal PPy nanosphere coating. Pollutant sensing was proposed from material properties, but it was not tested.
Composite fabrication and process conditions
Section titled “Composite fabrication and process conditions”The authors grew BDD on 10 × 15 mm² titanium foam with 30 μm pores by hot-filament chemical vapor deposition. Ethanol was the carbon source at 0.26 sccm. The B/C ratio was 1/1000, and deposition ran at 3000 Pa and 700 °C for 7 h. HFCVD left angular BDD grains about 0.69 μm in size over the foam skeleton.
PPy was then formed by oxidative polymerization in an ice bath. The authors mixed 0.1 M pyrrole and 0.1 M FeCl3·6H2O, immersed the BDD film, and stirred the mixture. Each sample was rinsed with deionized water and dried at 40 °C for 0.5 h. Polymerization times of 8, 12, 16, and 20 h produced the four test conditions.
Electrochemical measurements used the composite as the working electrode, a 10 × 15 mm² platinum sheet as counter electrode, and Ag/AgCl with 3 M KCl as reference electrode. The reported values came from three independently prepared electrodes for each polymerization time. The authors also identify HFCVD as a process that consumes substantial time.
Morphology and surface chemistry
Section titled “Morphology and surface chemistry”XRD showed that PPy deposition left the diamond structure unchanged, while PPy was amorphous. SEM of the 12 h sample found PPy particles with an average diameter of about 260 nm and little agglomeration. Gaps between the particles formed a nanoscale network above the titanium foam’s 30 μm pores. EDS mapping placed carbon and nitrogen in the same regions, which supported uniform PPy coverage.
Raman spectroscopy gave PPy bands near 1585 cm⁻¹ and 1340 cm⁻¹. The diamond sp³ C peak near 1332 cm⁻¹ was weak after PPy deposition.
XPS resolved pyrrolic NH at 399.9 eV, polaronic protonated nitrogen at 401.0 eV, bipolaronic nitrogen at 404.2 eV, and iminic nitrogen at 397.8 eV. Residual iron and chlorine signals were below 0.5 at%. The authors found no extra redox peaks in CV, so these residues did not appear to affect measurements under their conditions.
Electrochemical performance
Section titled “Electrochemical performance”CV curves at 10 mV/s had quasi-rectangular shapes without distinct redox peaks. The authors treated these profiles as capacitive behavior with good reversibility. BDD/PPy-12 h had the largest enclosed area, which suggested the highest specific capacitance. GCD curves at 1 mA/cm² were nearly triangular and showed good reversibility.
Areal capacitance at 1 mA/cm² was 237.9 ± 9.1 mF/cm² after 8 h and 398.6 ± 15.2 mF/cm² after 12 h. It was 359.8 ± 13.7 mF/cm² after 16 h and 303.4 ± 11.6 mF/cm² after 20 h.
The authors linked the 12 h result to a uniform PPy coating that added electroactive area and pseudocapacitance without blocking ion paths. They assigned the lower 8 h value to insufficient PPy loading. At 16 and 20 h, excess PPy agglomerated and hindered electrolyte infiltration. The 12 h result was the best among the four tested durations under this recipe.
EIS covered 0.01 Hz to 100 kHz with a 5 mV AC amplitude at open-circuit potential. The fit used Rs(CPE(RctWo)), with a constant phase element for porous electrode capacitance and a Warburg term for semi-infinite diffusion. For 12 h, Rs was 2.3 ± 0.2 Ω and Rct was 1.3 ± 0.1 Ω. The fit chi-square values were below 1 × 10⁻³ for all samples.
Rate behavior and reproducibility
Section titled “Rate behavior and reproducibility”The 12 h electrode showed a phase angle of approximately -78° at 0.01 Hz, close to the -90° response of an ideal capacitor. Its low-frequency impedance modulus was the lowest among the four samples. The supporting information specifies 0.1 M Na₂SO₄ for these Bode measurements.
Increasing the CV scan rate from 10 to 100 mV/s reduced specific capacitance from 353.2 to 187.8 mF/cm². The reported retention was 53%. GCD curves remained triangular from 1.0 to 1.8 mA/cm². The authors attributed the rate loss to limited time for ions to reach inner active sites.
Reproducibility was based on three independent synthesis batches per polymerization time. One electrode from each batch was measured in triplicate. The reported mean ± SD used the three batch means. This protocol shows that ion access constrains high-rate operation, even when nominal areal capacitance is high.
Comparison with reported electrodes
Section titled “Comparison with reported electrodes”Selected entries from the paper’s Table 1 show how the result compares with other BDD and PPy electrodes. The table mixes areal and volumetric capacitance, so units are retained below. The comparison also uses different current densities for each electrode.
| Electrode | Reported capacitance | Current density | Rct |
|---|---|---|---|
| Porous BDD/PPy | 398.6 ± 15.2 mF/cm² | 1.0 mA/cm² | 1.3 ± 0.1 Ω |
| Porous BDD | 67.9 mF/cm² | 0.22 mA/cm² | 81 Ω |
| Ti/BDD | 45.7 mF/cm² | 0.02 mA/cm² | 4.8 Ω |
| Porous BDD/MnO₂ | 1383.6 mF/cm² | 2 mA/cm² | 2 Ω |
| BG/BDD | 203.9 F/cm³ | 0.65 A/cm³ | 2.4 Ω |
| PPy | 0.54 F/cm² | 2.5 mA/cm² | 142.3 Ω |
| PPy/MXene | 1.975 F/cm² | 2.5 mA/cm² | 49.5 Ω |
The 1.3 Ω Rct was below 2 Ω for porous BDD/MnO₂, 2.4 Ω for BG/BDD, 4.8 Ω for Ti/BDD, 49.5 Ω for PPy/MXene, and 142.3 Ω for pure PPy. Porous BDD/MnO₂ had the highest listed areal capacitance, 1383.6 mF/cm² at 2 mA/cm².
The authors report 5.8 times the capacitance of porous BDD. Table 1 lists current densities of 1.0 and 0.22 mA/cm² for BDD/PPy and porous BDD, respectively. The comparison therefore is not rate matched. The clearest result is the low interfacial resistance across the listed systems, not a universal capacitance lead.
Sensing feasibility and unresolved questions
Section titled “Sensing feasibility and unresolved questions”No direct pollutant-sensing experiment was performed. The proposed case rests on low Rct and the observed pyrrolic NH groups. A lower Rct typically permits higher stripping peak currents and faster response in stripping voltammetry. The NH groups have lone pairs that can chelate heavy metal ions such as Pb²⁺, Cd²⁺, and Hg²⁺. They can also bind some organic molecules with electrophilic sites. Such chelation may preconcentrate pollutants at the electrode surface and support a lower detection limit. The porous architecture may also aid mass transport.
These properties establish theoretical feasibility only. The paper reports no detection limit, selectivity, calibration, response time, or analyte recovery for the composite. It calls for square-wave anodic stripping voltammetry for metal ions or amperometric detection for organic pollutants.
The proposed interface mechanism remains unverified. The band diagram uses literature work functions of 4.8 to 5.0 eV for p-type BDD and 4.5 to 4.7 eV for PPy. It proposes a narrow depletion region after Fermi-level alignment, but direct work-function measurements and interface characterization were outside the study.
For device engineering, the data support a coated, three-dimensional BDD electrode over planar BDD for low-resistance energy storage. The 53% rate retention and time-consuming HFCVD step remain limits to consider in high-rate and manufacturing designs. For sensing, the material is a candidate for validation, not a demonstrated detector.
Materials and support
Section titled “Materials and support”For this study, the relevant material is boron-doped diamond used as a conductive, porous electrode framework beneath a PPy layer. The diamond materials catalog includes boron-doped diamond and MPCVD-grown single-crystal and polycrystalline plates and wafers, while engineering support covers custom fabrication. Because the paper used HFCVD on titanium foam, 6CCVD’s offering is a material-family match rather than a validated substitute for the reported composite.
View Original Abstract
Self-powered integrated electrochemical systems require electrode materials that can simultaneously provide energy storage and sensing functions. Boron-doped diamond (BDD) electrodes have good chemical stability and a wide potential window, but their small specific surface area and slow interfacial charge transfer limit their use in such bifunctional applications. In this work, we prepared a three-dimensional porous BDD scaffold on titanium foam by hot-filament chemical vapor deposition, and then grew polypyrrole (PPy) layers on the scaffold by in situ oxidative polymerization. The polymerization time was varied from 8 to 20 h. The BDD/PPy composite obtained after 12 h showed an areal capacitance of 398.6 ± 15.2 mF/cm2 at 1 mA/cm2, which is about 5.8 times that of the porous BDD alone (67.9 mF/cm2). Its charge transfer resistance (Rct) was as low as 1.3 ± 0.1 Ω, among the lowest reported for BDD-based electrodes. The porous BDD framework provides ion diffusion pathways, while the PPy layer introduces pseudocapacitance. X-ray photoelectron spectroscopy reveals that the PPy layer contains pyrrolic -NH- groups, which are known to chelate various water pollutants (e.g., heavy metal ions and organic molecules). Based on these surface properties and the low Rct, we suggest that this composite may have theoretical potential for preconcentrating and detecting multiple pollutants. This work demonstrates a way to improve the capacitance of BDD-based electrodes and may serve as a starting point for future exploration in integrated energy-sensing devices after experimental validation.
Boron Doped Diamond On Titanium Bdd Electrode
View Specs →
Boron Doped Diamond Electrode On Niobium Bdd Nb Electrode
View Specs →
Boron Doped Single Crystal Diamond Plate
View Specs →References we cover
Section titled “References we cover”- Revolutionizing Electrochemical Sensing with Nanomaterial-Modified Boron-Doped Diamond Electrodes
- Sluggish Electron Transfer of Oxygen-Terminated Moderately Boron-Doped Diamond Electrode Induced by Large Interfacial Capacitance between a Diamond and Silicon Interface
- Diamond‐Based Supercapacitors with Ultrahigh Cyclic Stability Through Dual‐Phase MnO2‐Graphitic Transformation Induced by High‐Dose Mn‐Ion Implantation
Original source
Section titled “Original source”References
Section titled “References”- 2020 - Emerging Miniaturized Energy Storage Devices for Microsystem Applications: From Design to Integration [Crossref]
- 2019 - Integration of Electrochemical Microsupercapacitors with Thin Film Electronics for On-Chip Energy Storage [Crossref]
- 2023 - Self-Powered Sensing in Wearable Electronics—A Paradigm Shift Technology [Crossref]
- 2024 - Micro-Supercapacitors for Self-Powered Biosensors [Crossref]
- 2026 - Electrochemical Energy Storage and Sensing of Heavy Metal Ions by High-Energy Surface-Exposed Bifunctional Mn-Doped NiSe2 Nano-Octahedrons [Crossref]
- 2019 - A Novel Strategy of One Device Achieves Two Functions: Energy Storage and Temperature Sense Multi-Functions Device Based on Graphene Planar-Structure Supercapacitor [Crossref]