Electrochemical Detection of Vanadium Using a Boron‐Doped Diamond Electrode as a Surrogate for Radioactive Heavy Metals
Paper details
Section titled “Paper details”| Field | Value |
|---|---|
| Journal | Electroanalysis |
| Published | 2026-06-28 |
| Authors | Mingwei Bai, Michio Murata, Masaumi Nakahara, Yasuaki Einaga |
| DOI | 10.1002/elan.70182 |
The optimized method reached a limit of detection of 0.478 μM for vanadium in 0.5 M HNO₃. It used an O-terminated boron-doped diamond electrode, a deposition potential of -1.2 V versus Ag/AgCl, and a deposition time of 180 s. The calibration gave R² = 0.998. A neptunium-237 solution also produced an anodic feature near +1.7 V versus Ag/AgCl. These results support vanadium as a nonradioactive surrogate for developing neptunium monitoring methods.
Electrode selection determines the usable window
Section titled “Electrode selection determines the usable window”BDD had the widest anodic potential window and the lowest background current among the electrode materials tested. Platinum and gold showed large background currents from surface oxide formation and the onset of oxygen evolution. The authors report that those currents masked the target stripping signals. BDD therefore supplied the usable high-potential region for actinide-related oxidation peaks.
O termination improved signal stability and peak definition, so the authors selected it over the other tested surface states. They prepared the surface by anodic polarization at +3.0 V versus Ag/AgCl for 5 min in 0.2 M KOH, followed by ultrasonic cleaning in ultrapure water. Significant background suppression and a widened potential window served as practical evidence of the conversion. The paper does not report an independent chemical characterization of the termination.
Optimized measurement protocol
Section titled “Optimized measurement protocol”The measurements used a room-temperature, three-electrode cell with the BDD as working electrode, a platinum wire counter electrode, and an Ag/AgCl reference electrode. The BDD was prepared in-house by microwave-plasma-assisted chemical vapor deposition. It was as-deposited and unpolished, with a boron-to-carbon ratio of 1% in the source gas.
| Parameter | Optimized condition |
|---|---|
| Electrolyte | 0.5 M HNO₃ prepared with ultrapure water and high-purity HNO₃ |
| Working electrode | O-terminated BDD; 1.5 cm geometric diameter and 1 cm² effective area |
| Deposition | -1.2 V versus Ag/AgCl for 180 s under stirring |
| Rest | 10 s after stopping the stirrer |
| Stripping | LSV from -0.5 to +2.0 V versus Ag/AgCl at 100 mV/s |
| Blank treatment | Five consecutive CV scans before each ASV measurement |
Deposition at -1.2 V gave the maximum and most stable stripping peak current. The 180 s duration was chosen as a compromise between signal and analytical throughput. The paper does not report a total analysis time.
Calibration and analytical performance
Section titled “Calibration and analytical performance”Peak current rose with vanadium concentration, and the calibration was linear over the investigated range. The main text does not state the lower and upper calibration concentrations. Deposition preconcentrated vanadium at the electrode before the stripping scan.
The authors assign the peak near +1.1 V to reoxidation of deposited vanadium. They state that V(V) undergoes deep reduction at the deposition potential in strongly acidic media, with pH below 1, forming mainly V(II) solid oxides or metallic vanadium. The stripping process returns these species to soluble higher oxidation states, primarily VO2+ containing V(V).
The limit of detection was calculated as 3σ divided by the calibration slope, following the IUPAC definition. ASV gave the highest sensitivity and lowest limit of detection among cyclic voltammetry, differential pulse voltammetry, and square wave voltammetry under the same matrix conditions. The main text gives no numerical values for those three supporting-information comparisons, so the improvement cannot be quantified from the reported figures.
The paper positions stripping voltammetry as a simpler, on-site complement to ICP-MS and AMS. Those mass-spectrometric methods have excellent detection limits, but the authors cite complex instrumentation, high operating cost, and spectral interference in complex matrices. No direct sensitivity comparison with ICP-MS or AMS was performed.
Interference control in nitric acid
Section titled “Interference control in nitric acid”The authors defined interference as a vanadium peak-current change greater than ±10% or an overlapping signal in the relevant potential region. Figures 2 through 4 used 1 mM vanadium, 1 mM interferent, and their mixtures in 0.5 M HNO₃. Cs+, Ba2+, and ReO4− caused no significant interference in their tests.
The study then focused on Ru(III), Ce(III), and Pd(II), which were selected because of their electrochemical activity and tendency to co-extract with actinides in nitric-acid nuclear waste.
Ru(III) produced an overlapping high-potential response. Raising the pH to 5.5 with KOH formed ruthenium hydroxide species, which were removed by centrifugation. The vanadium calibration remained unchanged after this treatment, and recovery stayed within 95% to 105%. The authors attribute a small baseline discrepancy to changed ionic strength and slight competitive adsorption on BDD sites.
Ce(III) produced a broad background signal that overlapped the vanadium peak. Phosphoric acid suppressed the cerium contribution and shifted the vanadium peak to about +1.6 V versus Ag/AgCl, creating separation. A standard-addition test then supported quantitative determination in the presence of Ce(III). The phosphoric acid reagent was an 85 wt% solution, but the paper gives no added volume.
Pd(II) remained the limiting interference. Its dominant electrochemical response obscured vanadium. The authors tested SCN−, Cl−, F−, citrate, H₃PO₄, and pH adjustment without recovering a clear vanadium peak. Vanadium remained suppressed even at elevated vanadium-to-palladium ratios. They state that a Pd-specific separation is required before analysis of palladium-containing samples.
Neptunium-237 supports the surrogate approach
Section titled “Neptunium-237 supports the surrogate approach”Vanadium was selected because its oxidation states and aqueous speciation resemble those of neptunium in nitric acid systems. Under the optimized ASV conditions, the neptunium-237 solution gave a distinct anodic feature near +1.7 V versus Ag/AgCl. Its position was comparable to the vanadium signature under similar conditions. The authors use this agreement to support the origin of the peak and the validity of vanadium as the development surrogate.
The neptunium test was a qualitative proof of concept. The neptunium concentration was limited, and safety protocols and restricted facility access prevented concentration gradients and repeated baseline optimization. Baseline instability also occurred in the high-potential region. No neptunium LOD, calibration curve, precision, or recovery was reported.
Limits for on-site analysis
Section titled “Limits for on-site analysis”The reported 0.478 μM LOD applies to a controlled 0.5 M HNO₃ matrix, ultrapure water, high-purity supporting electrolyte, and a blank-cleaning step. It does not establish performance in untreated high-level liquid waste. Pd(II) interference is unresolved, and the neptunium result lacks quantitative validation. Baseline behavior also remains unstable near the highest measured potentials.
For material selection, the measurements support O-terminated BDD over the tested electrode materials and surface states under the reported nitric-acid conditions. The proposed use is an on-site complement to ICP-MS and AMS, not a demonstrated replacement. Deployment requires real-sample testing, matrix validation, and a separation strategy for palladium-bearing samples.
Materials and support
Section titled “Materials and support”The paper requires an MPCVD-grown boron-doped diamond working electrode for ASV in 0.5 M HNO₃, with O termination and a 1 cm² effective area. 6CCVD’s diamond materials catalog includes boron-doped diamond and MPCVD-grown single-crystal and polycrystalline diamond. Questions about matching that material to the electrode design can be directed to engineering support.
View Original Abstract
The release of radioactive heavy metals from radioisotope research laboratories necessitates rapid and on‐site analytical methods that complement conventional techniques such as inductively coupled plasma mass spectrometry (ICP‐MS) and accelerator mass spectrometry (AMS). In this study, a sensitive electrochemical detection method based on a boron‐doped diamond (BDD) electrode was developed in nitric acid media. Because experiments involving radioactive nuclides require specialized facilities, vanadium was employed as a nonradioactive surrogate to optimize anodic stripping voltammetry (ASV) conditions. Systematic optimization of experimental parameters, including electrolyte composition, electrode material, surface termination, and voltammetric method, identified ASV using an O‐terminated BDD electrode as the most effective approach. Under optimized conditions (deposition potential of −1.2 V [vs. Ag/AgCl] and deposition time of 180 s in 0.5 M HNO 3 ), a limit of detection (LOD) of 0.478 μM was achieved, outperforming CV, DPV, and SWV. Interference studies revealed that Ru(III) and Ce(III) significantly affect the vanadium signal but can be effectively mitigated by pH‐controlled precipitation and phosphoric acid addition, respectively. In contrast, Pd(II) interference remained unresolved due to its dominant electrochemical response. Finally, the applicability of the developed method to actinide‐relevant systems was demonstrated using a 237 Np solution, which exhibited a characteristic anodic signal at ~1.7 V (vs. Ag/AgCl), comparable to that of vanadium. These results highlight the potential of BDD‐based ASV for monitoring radioactive heavy metals in nitric‐acid environments.
Boron Doped Diamond On Titanium Bdd Electrode
View Specs →
Boron Doped Diamond Electrode On Niobium Bdd Nb Electrode
View Specs →
Boron Doped Single Crystal Diamond Plate
View Specs →Original source
Section titled “Original source”References
Section titled “References”- 1998 - A Table of Polyatomic Interferences in ICP‐MS
- 1985 - Stripping Analysis: Principles, Instrumentation, and Applications