Nonlinear ultrafast laser processing of diamond surfaces for precision microfabrication
Paper details
Section titled “Paper details”| Field | Value |
|---|---|
| Journal | Physical Sciences and Technology |
| Published | 2026-06-19 |
| Authors | Yelena White |
| DOI | 10.26577/phst20261312 |
Femtosecond laser ablation produced a curved feature with an estimated depth of 16 to 19 μm in HPHT single-crystal diamond at 0.8 μJ per pulse and 250 kHz. CVD diamond reached 12 to 13 μm at comparable pulse energy. The results show that single-crystal diamond supports deeper and sharper features than polycrystalline CVD diamond under the tested irradiation conditions.
Laser setup and depth measurement
Section titled “Laser setup and depth measurement”The custom system used a frequency-doubled Nd:YVO4 pump at 532 nm to drive a Ti:Sapphire oscillator and regenerative amplifier. It produced 800 nm pulses of approximately 200 fs. Pulse energies reached 4 μJ, and repetition rates reached 250 kHz. A neutral-density filter controlled power, while an external shutter controlled exposure. Objectives with numerical apertures of 0.85 and 0.90 produced a focal spot about 0.55 μm across. The microstage remained fixed as a piezoelectric stage translated the sample at about 11 μm/s.
Experiments took place in a Class-1000 clean room after ultrasonic cleaning with acetone, methanol, and deionized water. Two diamond materials were tested. The first was single-crystal diamond made by the high-pressure high-temperature process, called HPHT. The second was a polycrystalline diamond film made by plasma-enhanced chemical vapor deposition, called PECVD.
Depth was measured after processing by cellulose acetate replication and scanning electron microscopy. The authors coated both replicas and diamond samples with carbon, platinum, or gold for SEM imaging. They tilted some replicas by 45 degrees to estimate depth from the resulting nanowire profiles. Incomplete acetate penetration can lower the measured replica height. The paper therefore treats depths for features with a high aspect ratio as approximate lower bounds.
CVD crater geometry and graphitization
Section titled “CVD crater geometry and graphitization”At 250 kHz and 0.8 μJ per pulse, CVD craters measured about 750 nm in diameter. Their center-to-center spacing was about 3.5 μm. At 1.2 μJ, crater diameter approached 2 μm, and array spacing increased to about 4.5 μm. At the same 1.2 μJ energy, separate tests used spacing of about 3 μm and 2.5 μm. The smaller spacing caused stronger overlap and formed a continuous pattern. The diameter trend agrees with logarithmic fluence scaling reported for ultrafast micromachining of dielectric materials.
Textured material between craters at higher energy suggested partial sp³ to sp² conversion. The authors attributed this response to laser-induced graphitization. Prior work cited by the authors places the converted layer near the ablation threshold at tens to approximately 100 nm. They expect the layer at the tested fluences to remain superficial. They state that this thin layer should not compromise structural integrity for microfluidic or field-emission use. For electronic or photonic surfaces that require pristine diamond, they suggest oxidative etching to remove sp² material. The paper does not report such postprocessing.
Channels and larger structures
Section titled “Channels and larger structures”An array ablated at 2.2 μJ with 10 μm spacing between sites produced craters with an estimated depth of about 6 μm. Channels formed by sequential pulses along one path. Examples made at 0.8 and 2.2 μJ had defined edges, minimal debris, and widths of 1 to 2 μm. A line array made at 1.8 μJ used about 4 μm horizontal spacing. Its feature widths ranged from 0.8 to 1 μm.
The 0.55 μm focal spot was narrower than these machined lines. The authors linked the broadening to extreme pulse overlap and incubation. Incubation lowered the effective ablation threshold across more of the beam. At 11 μm/s and 250 kHz, they estimated about 12,500 overlapping pulses per spot diameter. The area of the Gaussian beam above threshold also expanded at 1.8 μJ. A square reservoir written at 3 μJ had sides of about 40 μm and an estimated depth of about 8.8 μm.
Single-crystal depth advantage
Section titled “Single-crystal depth advantage”A curved pattern machined in HPHT single-crystal diamond at 0.8 μJ and 250 kHz had an estimated depth of 16 to 19 μm. The comparable CVD structure reached 12 to 13 μm. HPHT diamond also produced sharper edges and more repeatable curved morphology. The paper attributes this contrast to material structure rather than a change in laser setup.
Earlier work cited by the authors links diamond ablation to crystal order, defect density, and nonlinear ionization. The result gives a direct process comparison at comparable pulse energy. It also supports the paper’s wider finding that feature geometry depends on diamond type, not only on deposited energy.
Proposed nonthermal ablation mechanism
Section titled “Proposed nonthermal ablation mechanism”At 250 kHz, the interval between pulses was 4 μs, much longer than the 200 fs pulse width. The authors argued that heat dissipated between successive pulses in both materials. Single-crystal thermal diffusivity was about 1200 mm²/s. Grain boundaries and sp²-rich intergranular phases reduce effective thermal conductivity in polycrystalline CVD diamond. The diffusion length during the 4 μs interval still exceeded the focal volume. Clean SEM morphology and minimal heat-affected zones supported the nonthermal interpretation. The paper cites earlier diamond-structuring studies at comparable repetition rates as supporting this picture.
Ideal single-crystal diamond is largely transparent at 800 nm because its bandgap is about 5.5 eV. Energy deposition therefore begins through nonlinear absorption. During the pulse, multiphoton and tunneling ionization seed electrons. Inverse bremsstrahlung gives electrons energy, and avalanche ionization multiplies the electron population. A dense transient plasma forms in the focal volume. After the pulse, electron-phonon coupling transfers energy to the lattice on a picosecond timescale. Coulomb explosion and phase explosion may both contribute above the ablation threshold.
The authors interpret the HPHT result through its ordered sp³ lattice and low density of grain boundaries. This structure supports efficient avalanche ionization and dense plasma buildup. In CVD diamond, grain boundaries, structural defects, and sp²-rich regions increase sub-bandgap absorption. They also act as recombination centers and scattering sites. These effects reduce plasma buildup and energy coupling to the lattice. The proposed interaction mechanisms are not direct plasma measurements.
Measurement limits and unresolved issues
Section titled “Measurement limits and unresolved issues”The main measurement limitation is acetate replication. Its fidelity falls as feature aspect ratio rises, and incomplete filling can underestimate depth. The reported depths should therefore be checked against the original structures when dimensional acceptance matters. The study reports no numerical ablation threshold, removal rate, throughput, or statistical repeatability.
All reported scanning used about 11 μm/s. The conclusion identifies scan speed as a control for channel width, but the study does not show a speed sweep. Graphitization was inferred from surface texture and prior literature rather than direct phase analysis. The proposed microfluidic, field-emission, and photonic uses also lack device performance tests. The results establish geometric processing capability rather than completed device performance.
Device engineering implications
Section titled “Device engineering implications”For designs where depth and edge definition are the main goals, the results favor HPHT single-crystal diamond. It produced deeper and sharper structures than PECVD diamond under comparable irradiation. Polycrystalline CVD diamond remains machinable. Its pulse-energy response offers control over crater diameter and site overlap.
At the tested energy, site spacing strongly affects whether adjacent craters remain separate or form a continuous structure. Repeated paths produced channels and line arrays, while programmed paths can form reservoirs. Engineers designing photonic or electronic CVD surfaces should assess the sp²-rich layer before relying on the machined surface. The authors propose oxidative etching when pristine diamond properties are required. Final device dimensions should be qualified because the acetate method can report depths that are lower bounds.
Materials and support
Section titled “Materials and support”The paper uses HPHT single-crystal and PECVD polycrystalline diamond for 1 to 2 μm channels, field-emission structures, and photonic components. The process needs a diamond plate or film with defined geometry and surface condition, so requirements can be reviewed through engineering support. 6CCVD’s diamond materials catalog lists MPCVD-grown single-crystal and polycrystalline plates and wafers up to 125 mm, with thickness from 0.1 to 500 micrometers.
View Original Abstract
Ultrafast femtosecond laser processing provides a versatile platform for precision micro- and nanoscale modification of wide-bandgap materials such as diamond. In this work, the formation of microscale and submicron surface features on high-pressure high temperature (HPHT) single-crystal diamond and chemical vapor deposition (CVD) diamond films is investigated using high-repetition rate femtosecond laser pulses. Systematic experiments examined the influence of laser fluence, pulse energy, and spatial pulse overlap on ablation morphology, feature dimensions, and material response. Arrays of craters, microchannels, and reservoir structures were fabricated through localized ablation, demonstrating the capability of femtosecond laser processing for flexible surface microstructuring of diamond. Differences in ablation behavior between HPHT single-crystal and polycrystalline CVD diamond were analyzed in terms of structural and electronic properties. The depth of laser-machined features was determined using an acetate replication technique followed by scanning electron microscopy. Results show a strong dependence of feature geometry and ablation efficiency on processing conditions, with single-crystal diamond exhibiting deeper ablation and sharper features at comparable fluence. These findings highlight the role of nonlinear absorption and defect mediated carrier dynamics in ultrafast laser-diamond interactions and suggest applications in diamond based microfluidic devices, field-emission structures, and advanced electronic and photonic systems. Keywords: femtosecond laser, laser ablation, diamond micromachining, laser nanomachining, ultrafast laser processing.
Single Crystal Cvd Diamond Plate
View Specs →
Customized Single Crystal Cvd Diamond Plate
View Specs →