Recent works in the area of nanoscience and nanotechnology for coatings application—a review
Paper details
Section titled “Paper details”| Field | Value |
|---|---|
| Journal | Academia Nano Science Materials Technology |
| Published | 2026-09-18 |
| Authors | Pradipta Sankar Maiti, Tapan Kumar Dhar |
| DOI | 10.20935/acadnano8519 |
Chemical vapor deposition (CVD) ultrananocrystalline diamond reached friction coefficients of about 0.02 to 0.04 with essentially no measurable wear. The review identifies these coatings as established in commercial wear service. Polymer systems remain more flexible for broad-area use, but their friction coefficients of 0.06 to 0.35 can rise when a transfer film breaks down.
Evidence and deployment status
Section titled “Evidence and deployment status”The review covers peer-reviewed primary studies and reviews from roughly 2008 to 2025. It retained work with quantified coating-level performance and excluded synthesis or characterization without a coating application. Synthesis routes for the nanomaterials were deliberately out of scope, and the authors created no new data. Manufacturer and trade claims were flagged rather than treated as measured performance.
Four domains carry most of the analysis: mechanical reinforcement, POSS hybrids, biological interaction, and optical response. A fifth group covers superhydrophobic, photocatalytic, and radiative-cooling surfaces. Self-polishing antifouling paints and self-assembling structural-color finishes depend on manufacturer reports, partnerships, and early automotive pilots. The review says independent verification is still needed for those systems. The authors disclose employment by a commercial coatings manufacturer, although they report that the company did not influence the work.
Deposition method also sets the practical limits of each result. Dip coating is simple and scalable but offers limited thickness control. Spin coating gives uniform films on flat parts but wastes material. Spray coating is used for large areas and automotive finishing. Sol-gel and layer-by-layer assembly allow molecular-level control at lower throughput. Electrophoretic and electrodeposition routes suit complex geometries.
Filler geometry controls reinforcement
Section titled “Filler geometry controls reinforcement”Coating performance depends on filler shape, dispersion, and stable transfer-film formation. Zero-dimensional particles include nano-SiO2, TiO2, carbon black, and fullerenes. They fill pores and redistribute stress, but agglomeration can reverse the gains above an optimum loading.
Adhesion remains governed mainly by resin or binder chemistry, not by the filler. Dispersion, wetting, and agglomeration therefore decide whether the intended benefit appears.
One-dimensional fillers such as multiwalled carbon nanotubes and nanowires carry load over long distances. In an epoxy study, poly(2-butylaniline) served as a dispersant and promoted uniform nanotube distribution in tetrahydrofuran. The optimum wear resistance occurred at about 5 wt% MWCNT. Many other systems reached their best performance below 5 wt%.
Two-dimensional nanosheets support interlayer shear and tortuous transport paths. Weak interlayer bonding also allows restacking. Three-dimensional hybrids pair load-bearing units with lubricating layers, but their synthesis and uniform dispersion remain difficult.
Hybrid fillers reach lower friction
Section titled “Hybrid fillers reach lower friction”NbSe2 nanosheets reduced the friction coefficient of epoxy from about 0.337 to 0.062 as loading increased from 0 to 20 wt%. The reported change was an 80% reduction. However, 20 wt% was unusually high for a nanosheet and could raise viscosity and cost.
An h-BN/MoS2 hybrid reduced friction by about 80% and wear rate by about 88% relative to neat epoxy. A ternary CNT/GO/MoS2 hybrid reached a friction coefficient of about 0.042 and a wear rate of 3.4 × 10⁻⁵ mm³ N⁻¹ m⁻¹. It performed better than every single-filler coating in that study.
A Ti3C2/graphene hybrid reduced epoxy wear rate by roughly 89%. These results connect lower friction with load transfer and stable sliding films. They do not solve dispersion problems, because hybrid fillers were harder to disperse uniformly.
POSS links molecular dispersion to multifunction
Section titled “POSS links molecular dispersion to multifunction”Polyhedral oligomeric silsesquioxane (POSS) is a 1 to 3 nm organic-inorganic cage with a silica-like core and tunable organic vertices. Formulators can blend it into a polymer, graft it onto a chain end, or use it as a multifunctional cross-linker. Molecular dispersion avoids much of the agglomeration that affects particulate fillers.
The hard-but-flexible GPOSS coating resisted a 9H pencil, while a polyurethane comparison failed under 3H. Its hardness was about 0.7 GPa, its elastic recovery was about 79%, and it retained integrity through more than 500 bending cycles.
Fluorinated POSS reduced ice adhesion to about 3.8 kPa and remained durable through icing and de-icing cycles. A 0.5 wt% POSS tetraaniline-modified graphene additive improved epoxy resistance to NaCl ingress. A Diels-Alder POSS nanocomposite also repaired cracks after heating above 94 °C and cooling to room temperature.
UNCD defines the high-duty benchmark
Section titled “UNCD defines the high-duty benchmark”The review positions CVD ultrananocrystalline diamond above polymer systems for sustained low-friction service. Its 2 to 5 nm grain structure supports the reported friction performance. The coatings show hardness up to about 97 GPa, essentially no measurable wear, and reported water contact angles of about 160 to 178 degrees.
UNCD surfaces are also strongly hydrophobic and biocompatible. Cited commercial uses include mechanical pump seals, bearings, and effectively wear-free atomic force microscopy probe tips. These duties favor a hard, low-wear surface over broad-area protection.
Table 2 records high CVD capital cost, rigid substrates as a limitation, and commercial readiness for seals, bearings, AFM, and implants. Selection between UNCD and a polymer coating therefore depends on duty cycle and substrate tolerance, not only the best laboratory friction value.
Antifouling and structural color need field verification
Section titled “Antifouling and structural color need field verification”Marine antifouling tests illustrate controlled biocide delivery. Copper-oxide nanocontainers with co-biocides kept hull sections fouling-free for one year of Adriatic service, while conventional paint fouled. Silver-coated mesoporous silica nanocapsules improved early-stage antifouling and reduced environmental impact relative to free biocide in the cited study.
Commercial self-polishing coatings are reported by manufacturers to reduce biocide elution and fuel consumption. The review does not treat those figures as independent measurements.
Brush-block structural-color copolymers self-assemble into ordered layers during ordinary drying. They can be applied by drawdown, brush, or spray. Molecular weight selects the reflected wavelength. Automotive partnerships and claimed specification compatibility still require independent verification before they establish production performance.
Cleaning and cooling coatings depend on processing
Section titled “Cleaning and cooling coatings depend on processing”A transparent silica and fluorosilane coating reached a water contact angle above 160 degrees with sub-100 nm roughness. A TiO2:ZnO sol-gel coating on polycarbonate used a 1:0.05 mixture and reached a contact angle below 5 degrees. The coating combined strong self-cleaning, high mechanical stability, and excellent wettability.
Transparent solar-control additives can work below about 10 wt% loading. Nano-antimony tin oxide in waterborne polyurethane lowered the interior film temperature by several degrees relative to ITO and FTO glazing.
Processing can reverse performance. Excessive annealing degraded silica and removed hydrophobicity in the methylated silica example. Open issues include tint control, additive cost and safety, and stability under prolonged heat and UV exposure.
Engineering selection depends on repeatability and risk
Section titled “Engineering selection depends on repeatability and risk”Peak laboratory performance is not the main adoption test. The authors argue that a coating delivering 90% of the laboratory benefit every batch is more useful than one delivering 100% intermittently. Agglomeration, field ageing, nanoparticle release, cost, and inconsistent test methods can erase a nominal gain.
EU REACH now places specific registration and characterization duties on nanoforms. Validated environmental risk methods are still developing. Formulators can reduce free-particle exposure by using encapsulated or matrix-bound nanophases. They also need exposure and life-cycle data for regulatory dossiers.
For wear-critical parts, UNCD offers the paper’s clearest commercial benchmark. For broad-area protection, formulation flexibility favors polymer systems. POSS suits multifunctional surfaces where molecular dispersion and low loading matter. Antifouling and structural-color claims should remain pilot choices until independent field data support them. The concrete selection rule is to match measured duty to dispersion, ageing, substrate, and regulatory constraints.
View Original Abstract
Nanoscience and nanotechnology have moved from the laboratory benchtop into industrial use, re-engineering surface coating technology. Since nanomaterials behave differently from their bulk counterparts, they can confer protection and entirely new functions at much lower loadings. This review surveys, from an industrial-application perspective, several of the domains in which that promise is now maturing: (i) nanoscale fillers that reinforce mechanical and tribological performance; (ii) polyhedral oligomeric silsesquioxane (POSS) as a molecularly defined organic-inorganic hybrid building block for hard-yet-flexible, anti-wetting, icephobic, anti-corrosive, fire-retardant, and self-healing coatings; (iii) nanomaterials that suppress biofilm formation and marine and medical biofouling; and (iv) structural-color systems that generate durable, pigment-free color. For each domain we set out the structure-property relationship and compare the leading additive families on the criteria that govern adoption: dispersion stability, durability under field conditions, environmental and health status, and cost. Synthesis methods are deliberately kept out of scope. We argue that the field’s central limitation is no longer demonstrating a function in the laboratory but reproducing it consistently, safely, and affordably at industrial scale. We benchmark these judgments against the systems that have advanced furthest toward use, and distinguish carefully between them: ultrananocrystalline-diamond wear coatings are in established commercial service, whereas the evidence for self-polishing antifouling paints and self-assembling structural-color finishes rests largely on manufacturer-reported performance, industrial partnerships and early automotive pilots that still require independent verification.
Diamond Heat Spreader With Copper Coated Metalized Surface
View Specs →
Electronic Grade Intrinsic Diamond Epitaxial Wafer H Terminated Superior 100 Mosfet Ready Substrate
View Specs →