Skip to content

Si‐Doped Nanocrystalline Diamond as Highly Sensitive Luminescence Thermometer for the Physiological Temperature Range (Adv. Funct. Mater. 72/2026)

FieldValue
JournalAdvanced Functional Materials
Published2026-09-01
AuthorsMaría Gragera, Iván Carrillo‐Berdugo, Josué Millán-Barba, Paulius Pobedinskas, Antonio Freire
DOI10.1002/adfm.77983

The paper identifies Si-doped nanocrystalline diamond as a highly sensitive luminescence thermometer for the physiological temperature range. The supplied body contains only the journal header and website, so its performance claim cannot be checked against experimental measurements.

The title defines the proposed device. The sensing material is Si-doped nanocrystalline diamond. The readout is luminescence. The target is temperature measurement over the physiological temperature range.

The title characterizes the thermometer as “highly sensitive.” That description is qualitative. The supplied text does not define sensitivity or attach a number to it.

Several performance quantities remain undefined. The record gives no range limits, temperature resolution, accuracy, calibration uncertainty, response time, or repeatability.

It does not link sensitivity to silicon content, nanocrystal size, or phase. The title therefore supports a device class and target application. It does not support a performance claim that can be checked against data.

The bibliographic record identifies Advanced Functional Materials, volume 36, issue 72, dated September 7, 2026. The DOI is 10.1002/adfm.77983.

The extracted body contains only the journal header and website. It has no abstract, experimental section, results, discussion, references, figure captions, or supporting information.

The supplied metadata also omits the author list. No textual claim from the authors can be checked beyond the title and bibliographic fields.

These omissions prevent a conventional result summary with experimental conditions. They also prevent reconstruction of the measurement chain and its uncertainty.

Any stronger conclusion would add information that is absent from the supplied source.

Material identity comes from the title alone. The record names no silicon concentration or incorporation source. It gives no growth method, substrate, sample thickness, or post-growth treatment.

Because no synthesis method is named, the material cannot be assigned to a known preparation route. The record also does not say whether silicon was introduced during growth or afterward.

Nanocrystalline grain dimensions, phase composition, and silicon distribution are also absent. No surface finish, facet orientation, or active area is reported.

These omissions prevent any link between preparation and sensitivity. A reader cannot determine whether the silicon was uniform. They also cannot determine whether the optical signal came from a single structural region or several.

The missing dimensions matter for reproduction and device design. They also prevent comparison with any named diamond thermometer platform.

The title names luminescence thermometry but gives no measurement configuration. It identifies no excitation wavelength, emission band, detector, optical filter, temperature stage, or reference thermometer.

It does not state whether the readout uses intensity, intensity ratio, peak position, linewidth, decay time, or another spectral parameter. The output signal cannot be reconstructed without that choice.

No calibration equation, fitting method, temperature increment, acquisition time, or averaging procedure appears. The record therefore does not show how the reported temperature was derived.

Sample geometry is missing as well. The source gives no optical access path, collection angle, sample thickness, or package arrangement. Thermal coupling between the sensing material and the measured environment is not described.

The source does not state whether the physiological reading was measured in a calibrated bath or on a controlled stage. It does not report the atmosphere or thermal field during measurement.

These are central details for a luminescence thermometer. Their absence prevents an assessment of measurement resolution or practical usability.

No scientific measurement number appears in the supplied text. The record contains no temperature value with units, sensitivity value, resolution, uncertainty, response time, or signal change.

The available numerals have bibliographic roles only. Volume 36 and issue 72 identify the journal issue. The year 2026 and the label 72/2026 identify publication information. The DOI is an identifier rather than a result.

No table can report scientific performance because the extracted material contains no performance values. Values for a physiological range taken from outside the paper would not describe this experiment.

The strongest number available is therefore bibliographic rather than experimental. The supplied record does not permit a quantitative headline.

The phrase “highly sensitive” requires a reference point, but the extracted text provides none. No previous material, commercial thermometer, or competing nanocrystalline system is named for comparison.

No improvement factor, calibration slope, limit of detection, or signal-to-noise ratio is given. No criterion defines the physiological range or explains its relevance to the reported performance.

The comparison is incomplete. The title offers no sensitivity value to compare. The supplied body offers no baseline against which a value could be judged.

Prior work cannot be discussed safely because the reference list is absent. The article cannot claim superiority, parity, or a trade-off with another material.

The usable engineering result is the proposed application class. It is a luminescence-based temperature sensor made from Si-doped nanocrystalline diamond for physiological conditions.

Even that statement leaves major design constraints open. The optical excitation and detection scheme remain unspecified. The relation between temperature and measured luminescence remains unspecified. The acceptable accuracy also remains unspecified.

An engineer cannot select an excitation source or detector from this record. A calibration budget cannot be set. Integration cannot account for drift, thermal contact, or optical collection efficiency. No test data address those issues.

Device packaging cannot be specified from the record. The source does not state whether the diamond is a free-standing body, a coating, or a component in an optical assembly.

Material selection also cannot rely on the silicon label alone. The source does not relate silicon content to signal level, stability, or calibration. It does not identify a preferred nanocrystalline structure.

No performance qualification should be assigned until the full experimental record is available. This is a source limitation, not a negative finding by the authors.

Evidence required for an engineering decision

Section titled “Evidence required for an engineering decision”

Restoring the full paper is required for a technical evaluation. The preparation chain must specify silicon loading, growth conditions, thickness, microstructure, and surface condition.

The measurement chain must specify optical settings, the luminescence signal used, temperature control, calibration, repeated measurements, and uncertainty.

Reproducibility also depends on the data-processing chain. The paper must define how raw luminescence data are converted into temperature and how fit quality is assessed.

A sensitivity claim also requires a defined metric and comparator. The physiological range requires numerical limits. The evaluation must report response time and stability conditions.

These records would allow comparison with other luminescence methods. They would also show whether the reported sensitivity fits an intended device.

Until the full paper is available, the title supports only a device class. It does not support a performance-qualified thermometer design.

View Original Abstract

Luminescent Thermometry Nanodiamonds are emerging as highly promising materials for luminescent thermometry in the physiological temperature range due to their excellent biocompatibility, chemical inertness, and optical transparency. In this work, diamonds with SiV− centers have been designed for use as thermometers in biomedical applications. Multiparametric analysis of the emission characteristics of the SiV− centers provides extraordinary sensitivity for temperature detection in the physiological temperature range. More details can be found in the Research Article by Iván Carrillo-Berdugo, Javier Navas, and co-workers (DOI: 10.1002/adfm.77324).