Skip to content

Preparation And Cutting Performance Of Boron-Doped Diamond Coating On Cemented Carbide Cutting Tools With High Cobalt Content

MetadataDetails
Publication Date2015-03-01
JournalZenodo (CERN European Organization for Nuclear Research)
AuthorsZhaozhi Liu, Feng Xu, Junhua Xu, Xiaolong Tang, Ying Liu
Citations1
AnalysisFull AI Review Included
  • Objective: Development of Boron-Doped Diamond (BDD) coatings on cemented carbide (WC-Co) cutting tools with high cobalt content (10 wt.% Co), overcoming the traditional 6 wt.% Co limitation.
  • Substrate Innovation: Utilizes YG330 grade Φ3.2 mm WC-10 wt.% Co drills, which offer superior toughness and strength for machining difficult-to-cut materials.
  • Process Technique: Chemical Vapor Deposition (CVD) with dynamic boron doping during the growth phase to refine grain structure and reduce internal film stress.
  • Key Achievement: SEM analysis confirmed no cracks or collapses in the BDD coating, indicating successful adhesion despite the high Co content.
  • Cutting Performance: Tested against silumin (high-Si Al alloy) and aluminum-base Printed Circuit Boards (PCB), demonstrating minimal wear and no coating delamination during operation.
  • Engineering Significance: Demonstrates that BDD is not limited to electrochemical applications but serves as a highly effective wear-resistant layer for advanced machining of composites and non-ferrous alloys.
ParameterValueUnitContext
Substrate MaterialYG330 Cemented Carbide—Grade designation for the WC-Co substrate
Substrate GeometryΦ3.2mmDrill diameter
Cobalt (Co) Content10wt.%High Co content (traditional limit is <6 wt.%)
Coating TypeBoron-Doped Diamond (BDD)—Dynamic introduction of boron during CVD growth
Boron Dopant EffectGrain refinement & stress reduction—Improves film quality and morphology
Workpiece 1Silumin (Al-Si Alloy)—Difficult-to-machine non-ferrous alloy
Workpiece 2Aluminum-base PCB—Printed Circuit Board with Al substrate
Coating Integrity (SEM)Crack-free, no collapses—Confirms successful nucleation and adhesion
Adhesion PerformanceNo delamination observed—Verified during active cutting tests
  1. Substrate Selection: Φ3.2 mm YG30 grade cemented carbide drills with 10 wt.% Co content were selected as the base material to leverage enhanced toughness over standard low-Co substrates.
  2. Pretreatment: Chemical etching procedures were applied to selectively remove surface Co binder, mitigating its catalytic effect on graphite formation during diamond nucleation.
  3. CVD Deposition Setup: Diamond films were deposited via Chemical Vapor Deposition with dynamic boron doping introduced during the growth process.
  4. Optimization: CVD parameters were optimized specifically for the high-Co substrate to ensure uniform nucleation and continuous film coverage.
  5. Characterization: Coating morphology and structural integrity were verified using Scanning Electron Microscopy (SEM) to check for cracks and collapse defects.
  6. Cutting Test Protocol: Coated drills were evaluated in practical machining scenarios against silumin alloys and aluminum-base PCBs to assess wear resistance and coating retention.
  7. Performance Evaluation: Wear amount and surface precision of the machined workpieces were measured, alongside visual inspection of the coating post-test to verify adhesion durability.
  • Applicable Materials: This research utilizes Boron-Doped Polycrystalline Diamond (BDD PCD). To replicate or extend this work, 6CCVD recommends our Heavy Boron-Doped PCD or Light Boron-Doped PCD grades, which allow precise control over electrical conductivity, grain refinement, and film stress—key factors identified in the paper for successful high-Co substrate adhesion.
  • Substrate Compatibility: While this paper focuses on CVD coatings directly on WC-Co tools, 6CCVD provides high-quality PCD cutting tool blanks (up to 125mm) that can be brazed or directly manufactured into complex drill geometries, eliminating the CVD-on-carbide adhesion challenges entirely.
  • Customization Potential: The paper highlights the difficulty of maintaining adhesion on WC-10 wt.% Co. 6CCVD bypasses this limitation by offering freestanding PCD plates with custom thicknesses (0.1 µm to 500 µm for films, up to 10mm for substrates). We also provide custom metalization services (Ti, Pt, Au, W, Cu) for applications requiring brazing integration into tool assemblies.
  • Precision Shaping: For advanced tool geometries like the Φ3.2 mm drills tested here, 6CCCCVD offers laser cutting and precision shaping to deliver finished PCD cutting edges with tight dimensional tolerances, ready for immediate tool fabrication.
  • Engineering Support: 6CCVD’s in-house PhD engineering team specializes in matching diamond material grades to specific machining applications. Whether your project involves machining high-silicon aluminum alloys, composites, or PCBs, we can recommend the optimal boron-doping level and PCD grain size to maximize tool life.
  • Global Logistics: 6CCVD ships worldwide with flexible Incoterms (DDU default, DDP available), ensuring reliable delivery of custom diamond solutions to research facilities and production lines globally.

For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

Chemical vapor deposition (CVD) diamond coated cutting tool has excellent cutting performance, it is the most ideal tool for the processing of nonferrous metals and alloys, composites, nonmetallic materials and other difficult-to-machine materials efficiently and accurately. Depositing CVD diamond coating on the cemented carbide with high cobalt content can improve its toughness and strength, therefore, it is very important to research on the preparation technology and cutting properties of CVD diamond coated cemented carbide cutting tool with high cobalt content. The preparation technology of boron-doped diamond (BDD) coating has been studied and the coated drills were prepared. BDD coating were deposited on the drills by using the optimized parameters and the SEM results show that there are no cracks or collapses in the coating. Cutting tests with the prepared drills against the silumin and aluminum base printed circuit board (PCB) have been studied. The results show that the wear amount of the coated drill is small and the machined surface has a better precision. The coating does not come off during the test, which shows good adhesion and cutting performance of the drill.