SRS in the strong-focusing regime for Raman amplifiers
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2015-05-29 |
| Journal | Optics Express |
| Authors | Aaron McKay, Richard P. Mildren, David W. Coutts, David J. Spence |
| Institutions | Macquarie University |
| Citations | 15 |
| Analysis | Full AI Review Included |
Executive Summary
Section titled “Executive Summary”- Objective: Theoretical and experimental validation of Stimulated Raman Scattering (SRS) in crystalline amplifiers utilizing a tightly-focused (strong-focusing) pump geometry to achieve efficient power transfer from a pump beam to a Stokes seed beam.
- Core Material: Single-Crystal Diamond (SCD) acting as the Raman-active medium, prized for its unmatched thermal conductivity and high optical damage threshold.
- Key Theoretical Achievement: Derivation of the minimum Stokes saturation power (order of 1 kW) required for an efficient single-pass Raman power amplifier, independent of crystal length in the tight-focusing regime (Rayleigh range shorter than the medium).
- Experimental Validation: Demonstration of pump-to-Stokes power conversion in an unguided, single-pass 9.5 mm-long CVD diamond amplifier.
- Peak Performance: Achieved a maximum Stokes amplification factor (Gain) of 5.8x and a pump depletion of 66% using a 10.4 kW pump and a 1.2 kW Stokes seed.
- System Efficiency: Near quantum-defect-limited efficiency (~79% compared to the theoretical limit of 85.8% for a 1064 nm to 1240 nm conversion).
- Future Application: Enabling the amplification and coherent beam combination of high-power continuous-wave (CW) lasers by cascading amplifier stages.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Raman Gain Coefficient (SCD) | 10 | cm/GW | Stationary gain at ~1 µm wavelength (general literature range: 8 - 17 cm/GW) |
| Measured Gain (Strong-Focusing) | 9.9 | cm/GW | Validated experimentally with zR ≈ 0.146l |
| Measured Gain (Collimated) | 10.5 | cm/GW | Validated experimentally with zR ≈ 0.48l |
| Raman Linewidth | 1.5 | cm-1 | Characteristic of diamond at room temperature |
| Pump Wavelength (λF) | 1064 | nm | Nd:YAG fundamental |
| Stokes Wavelength (λS) | 1240 | nm | First Stokes shift output |
| Refractive Index (n) | 2.41 | - | Diamond refractive index |
| Quantum Defect Limit (η) | 85.8 | % | Theoretical maximum for 1064→1240 nm |
| Experimental Conversion Efficiency | ~79 | % | Achieved in the depleted pump regime |
| Pump Peak Power | Up to 10.4 | kW | Input to the amplifier stage |
| Stokes Seed Peak Power | 1.2 | kW | Required to exceed saturation threshold (PSsat = 1.1 kW) |
| Pulse Duration | 10 | ns | Nanosecond Q-switched pulses |
| Focused Waist Diameter | ~28 to 33 | µm | Pump and seed beam waist in diamond |
| Thermal Fracture Limit | 1 | MW | Estimated upper bound for diamond |
| Optical Damage Threshold (Coated) | > 220 | MW/cm2 | Surface damage threshold of AR-coated diamond |
Key Methodologies
Section titled “Key Methodologies”- Crystal Growth & Fabrication: Utilization of CVD-grown single-crystal diamond (Type IIIa, Element Six, UK). Crystal cut along the ⟨110⟩ crystallographic axis to align with the ⟨111⟩ high-gain polarization axis.
- Optical Coating: End-faces of the amplifier diamond were Anti-Reflection (AR) coated for 1240 nm. The seed laser cavity utilized dielectric mirrors tuned for 1240 nm first-Stokes generation.
- Thermal Management: The amplifier crystal was fixed to a copper heat sink using silver-impregnated thermal paste.
- Optical Setup (Pump Path): A commercial 1064 nm Q-switched laser (ESKPLA NL-220) was passed through a Faraday isolator and split into two paths using a dichroic beam splitter.
- Seed Laser Configuration: A diamond Raman laser utilizing an 8 mm-long crystal, a 20 cm radius-of-curvature input mirror, and a planar output mirror. The Stokes output was filtered to remove residual 1064 nm and 1480 nm second-Stokes components.
- Beam Combining & Mode Matching: Pump and seed beams were combined on a dichroic mirror and polarized using a Glan-laser polarizer. A telescope was used to match the waist size and divergence of the seed to the pump beam.
- Focusing Geometry: A 75 mm focal length doublet lens was used to focus the beams into the center of a 9.5 mm-long diamond amplifier.
- Measurement & Calibration: Pump and Stokes pulses were measured (pump blocked vs. pump on) using a single-lens magnifying system and an Ophir SP620 camera. Data was averaged over 16 traces and calibrated with a sensitive power meter.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”The precise optical and thermal demands of this high-power Raman amplification research align directly with the advanced manufacturing capabilities required for high-power laser systems. 6CCVD provides the foundational materials required to replicate, validate, or extend these findings.
- Applicable Materials:
- Optical Grade Single Crystal Diamond (SCD): The research relies on low-birefringence, ultra-high-purity SCD (Type IIIa equivalent). 6CCVD provides SCD substrates with thicknesses ranging from 0.1 µm to 500 µm, cut precisely along crystallographic axes (such as ⟨110⟩ or ⟨111⟩) to optimize polarization-dependent Raman gain.
- Custom Dimensions: The experimental setup utilized an 8 mm seed crystal and a 9.5 mm amplifier crystal. 6CCVD supports custom plate and wafer dimensions up to 125 mm (PCD) and provides custom SCD dimensions suitable for these tightly-focused intracavity and extracavity setups.
- Customization Potential:
- Optical Coatings: The paper required end-faces AR-coated specifically for the 1240 nm Stokes wavelength to minimize parasitic loss. 6CCVD offers custom optical coating integration, ensuring your diamond components arrive ready for complex resonator or amplifier integration.
- Metallization: For researchers looking to integrate diamond into thermally-soldered mounts or advanced beam-combining housings, 6CCVD features an internal metalization capability (Ti, Au, Pt, Pd, W, Cu) to provide robust, diffusion-bonded interfaces without compromising the diamond’s thermal properties.
- Laser Cutting & Shaping: The 9.5 mm length used in the experiment is easily achievable. 6CCVD offers precision laser cutting and shaping to meet specific confocal parameter (zR) and tight-focusing geometric requirements.
- Engineering Support:
- The paper notes that tightly-focused SRS necessitates exact Rayleigh range matching between the pump and seed beams. 6CCVD’s in-house PhD engineering team can assist with material selection, crystallographic orientation, and geometry design to ensure optimal beam overlap (M2 < 1.2) for your specific high-power CW or pulsed Raman amplifier projects.
- Quality Assurance: To achieve the demonstrated 5.8x gain and 79% efficiency, internal bulk losses (αL) must be negligible. 6CCVD provides ultra-low loss SCD with sub-surface polishing capabilities (Ra < 1 nm for SCD) to minimize scatter and maximize the Raman gain coefficient (g0).
Call to Action: For custom specifications, specific crystallographic orientations, or material consultation regarding your high-power Raman amplification and beam-combination projects, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
The theoretical analysis of stimulated Raman scattering (SRS) in crystalline amplifiers with a tightly-focused pump geometry is presented. We predict the minimum Stokes seed power required for an efficient Raman power amplifier and verify this result experimentally. Conversion of a pump to a Stokes beam in a single-pass diamond amplifier is demonstrated using nanosecond pulses with gains of 5.8 from a 1.2-kW peak-power Stokes seed beam. The results demonstrate the possibility of amplifying and combining high-power continuous-wave lasers using current diamond Raman laser technology.