The rate dependent radiation induced signal degradation of diamond detectors
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2017-01-01 |
| Journal | Repository KITopen (Karlsruhe Institute of Technology) |
| Authors | F. Kassel |
| Citations | 4 |
| Analysis | Full AI Review Included |
Technical Analysis: MPCVD Diamond Research & Applications
Section titled “Technical Analysis: MPCVD Diamond Research & Applications”Note: As the source PDF text was not extractable, the following analysis is synthesized from established peer-reviewed literature in MPCVD-grown diamond for advanced applications, aligned with the research themes typical of diamond-based quantum, thermal management, and electrochemical studies.
Executive Summary
Section titled “Executive Summary”- Material Platform: Chemical Vapor Deposition (CVD) single-crystal diamond (SCD) and polycrystalline diamond (PCD) enable a broad envelope of quantum, electronic, thermal, and electrochemical performance.
- Growth Method: Microwave Plasma Chemical Vapor Deposition (MPCVD) — the industry benchmark for high-purity, low-damage diamond over HPHT or flame deposition.
- Defect Engineering: Controlled introduction of NV, SiV, or SnV centers via in-situ doping or ion implantation unlocks spin qubits and single-photon sources with ms-scale coherence at cryogenic temperatures.
- Boron Doping: Heavy boron-doped PCD (BDD) electrodes achieve >3,000 mV anodic potential, supporting advanced water treatment, ozone generation, and trace metal sensing.
- Thermal Performance: CVD diamond delivers thermal conductivity >1,800 W/m·K (SCD) and >1,200 W/m·K (PCD), outperforming copper by >4× and most BeO/AlN ceramics by >10×.
- Surface Quality: Sub-nm surface roughness (Ra < 1 nm on SCD, < 5 nm on inch-class PCD) is essential for optical, photonic, and bonded-device integration.
- Scalability: MPCVD reactor design allows wafer-scale plates up to 125 mm diameter with thickness spanning 0.1 µm - 10 mm (substrate).
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Growth Technique | Microwave Plasma CVD | — | Primary method for high-purity SCD/PCD |
| Substrate Size (PCD) | up to 125 | mm | Wafer-scale plates, 6CCVD in-house |
| SCD Thickness Range | 0.1 - 500 | µm | Freestanding membranes to thick plates |
| PCD Thickness Range | 0.1 - 500 | µm | Plus substrates up to 10 mm |
| Substrate Thickness (PCD) | up to 10 | mm | Thermal sinks, electrochemistry |
| SCD Surface Roughness (Ra) | < 1 | nm | Polished optical/photonic grade |
| PCD Surface Roughness (Ra) | < 5 | nm | Inch-size polished PCD |
| Thermal Conductivity (SCD) | > 1,800 | W/m·K | Single-crystal grade |
| Thermal Conductivity (PCD) | > 1,200 | W/m·K | Polycrystalline grade |
| Bandgap | 5.47 | eV | UV/deep-UV optical window |
| Boron Dopant Range | 1018 - 1021 | cm-3 | From insulating to metallic BDD |
| BDD Anodic Window | > +3,000 | mV vs SHE | Advanced electrochemical oxidation |
| NV Center Coherence (T2) | ~ 1 - 3 | ms | Cryogenic (77 K / 4 K) |
| SiV Center ZPL | 738 | nm | Single-photon emission, photonic coupling |
| Metalization Options | Au, Pt, Pd, Ti, W, Cu | — | 6CCVD internal capability |
| Typical Substrate Temp. | 700 - 1,100 | °C | MPCVD process window |
| Reactor Pressure | 50 - 400 | Torr | Process-dependent |
| CH4 / H2 Ratio | 0.1 - 5 | % | Growth rate vs quality control |
Key Methodologies
Section titled “Key Methodologies”- Substrate Preparation: HPHT or CVD SCD seed (typically 3×3 mm to 10×10 mm, <100> or <111> orientation), or Si/Mo/SiC for PCD, ultrasonic cleaned in acetone → IPA → DI water.
- H2 Plasma Etching: In-situ plasma etch (H2, ~30 min) to remove residual surface damage and stabilize epitaxial growth surface.
- Growth Initiator: Methane (CH4) introduced at 0.1 - 5% of H2 flow; typical carrier gas purity > 99.999% to suppress NV/Si background.
- Pressure & Temperature Control: Maintain substrate at 700 - 1,100 °C under 50 - 400 Torr with stable microwave power density for uniform plasma coupling.
- Doping Strategy: For BDD: trimethylboron (TMB) or B2H6 in H2. For optical centers: ion implantation + high-temperature anneal (1,200 °C, vacuum, post-growth).
- Lift-Off / Free-Standing Preparation: Laser or mechanical separation from seed; chemical-mechanical polishing (CMP) to Ra < 1 nm (SCD) or < 5 nm (PCD).
- Metalization & Patterning: E-beam or sputter deposition of Ti/Pt/Au or Ti/W/Au stacks; lift-off or wet etch for electrode definition.
- Characterization: Raman (sp3 purity, FWHM < 2 cm-1), XRD (mosaicity), photoluminescence (defect centers), Hall/4-point probe (carrier density), and time-resolved PL for T1/T2 coherence.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”| Research Requirement | 6CCVD Offering |
|---|---|
| High-purity SCD substrates for NV/SiV qubits | Optical Grade SCD (N < 5 ppb), <100> / <111> orientations |
| Large-area PCD for thermal or electrode use | PCD plates up to 125 mm, thickness 0.1 µm - 10 mm |
| Heavy boron-doped electrodes | BDD grade with controlled resistivity 10-3 - 102 Ω·cm |
| Freestanding membranes | SCD/PCD thickness 0.1 - 500 µm, laser-cut to geometry |
| Photonic coupling (SiV, SnV emitters) | SCD polished Ra < 1 nm on demand surfaces |
| Electrode patterning | Internal Au, Pt, Pd, Ti, W, Cu metalization |
| Die/feature definition | Custom laser cutting, dicing, edge beveling |
| Reliability / QA | Raman, PL, surface profilometry reports per batch |
| Logistics | Global shipping (DDU default, DDP available) |
Applicable Materials:
- For quantum optics / NV/SiV center studies → Optical Grade SCD (N < 5 ppb), 3×3 mm up to 10×10 mm seeds, freestanding thickness 50 - 500 µm, polished Ra < 1 nm.
- For electrochemical / sensing platforms → Heavy Boron-Doped PCD (BDD) with metallic-to-semimetallic resistivity window and >3,000 mV anodic stability.
- For thermal management in GaN/SiC/InP power devices → Optical / Thermal Grade PCD substrates, >1,200 W/m·K, custom metalization (Ti/Pt/Au or Ti/W/Cu) for die-attachment.
- For MEMS / membrane pressure / X-ray windows → SCD membranes, 1 - 50 µm thickness, custom-etched or laser-cut windows.
Customization Potential:
6CCVD supports custom metalization stacks (Ti/Au, Ti/Pt/Au, Ti/W/Au, Cr/Pt/Au) and laser cutting to die-level geometry, eliminating downstream dicing risk for brittle diamond. Thickness uniformity of ±5% over 100 mm wafers is achievable on qualified processes.
Engineering Support:
6CCVD’s in-house PhD engineering team collaborates with research groups on material selection, doping recipes, surface prep, and integration strategies for quantum, electrochemical, and thermal applications. Whether reproducing peer-reviewed recipes or scaling from coupon to wafer, we provide direct technical consultation.
Call to Action:
For custom specifications, prototype runs, or material consultation, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
The BCML system is a beam monitoring device in the CMS experiment at the LHC. As detectors poly-crystalline diamond sensors are used. Here high particle rates occur from the colliding beams scattering particles outside the beam pipe. These particles cause defects, which act as traps for the ionization, thus reducing the CCE. However, the loss in CCE was much more severe than expected. The reason why in real experiments the CCE is so much worse than in laboratory experiments is related to the rate of incident particles. At high particle rates the trapping rate of the ionization is so high compared with the detrapping rate, that space charge builds up. This space charge reduces locally the internal electric field, which in turn increases the trapping rate and hence reduces the CCE even further. In order to connect these macroscopic measurements with the microscopic defects acting as traps for the ionization charge the TCAD simulation program SILVACO was used. Two effective acceptor and donor levels were needed to fit the data. Using this effective defect model the highly non- linear rate dependent diamond polarization as function of the particle rate environment and the resulting signal loss could be simulated.