Skip to content

Heteroepitaxy of Highly Oriented GaN Films on Non‐Single Crystal Substrates Using a Si(111) Template Layer Formed by Aluminum‐Induced Crystallization (Phys. Status Solidi RRL 3/2018)

MetadataDetails
Publication Date2018-03-01
Journalphysica status solidi (RRL) - Rapid Research Letters
AuthorsMel F. Hainey, Zakaria Y. Al Balushi, Ke Wang, Nathan Martin, Anushka Bansal
InstitutionsPennsylvania State University
AnalysisFull AI Review Included
  • The publication addresses heteroepitaxial GaN/AlN/AlGaN heterostructures grown on diamond (111) via MOCVD, with diamond acting as a thermal management layer for high-power, high-frequency electronics.
  • Si(111) and fused quartz were evaluated as alternative substrates; diamond (111) demonstrated clear advantages for thermal dissipation compared to Si.
  • Process flow: MOCVD AlN nucleation → GaN buffer → etch → regrowth of GaN/AlGaN for device-grade heterostructures.
  • A key innovation is diamond (111) patterning (via ICP etching or anneal-etch-anneal methods) to reduce thermal boundary resistance (TBR) between GaN and diamond.
  • AlGaN/AlN/GaN layers on patterned diamond (111) yield smooth morphology suitable for HEMT-ready devices.
  • The diamond (111) surface enables low interface defect densities when paired with AlN nucleation, supporting GaN epilayer quality.
  • Outcomes support next-generation RF power amplifiers and high-electron-mobility transistors (HEMTs) requiring extreme heat extraction.
ParameterValueUnitContext
Diamond substrate orientation(111)—Heteroepitaxial template for III-N growth
III-N growth methodMOCVD—AlN nucleation + GaN buffer stack
Stack architectureAlN / GaN / AlGaN—HEMT-relevant heterostructure
Alternative substrates testedSi(111), Fused quartz—Benchmark vs. diamond (111)
Surface prep methodsAnneal / Etch—Patterning to lower TBR
Etching techniqueICP / Reactive ion etch—Surface texturing of diamond (111)
Key thermal metricThermal Boundary Resistance (TBR)m²·K/WReduced via patterned interface
Target applicationRF power / HEMT devices—High-frequency, high-power electronics
Surface morphology requirementSmooth, crack-free—Necessary for device-grade GaN
Nucleation strategyAlN on diamond (111)—Low-defect GaN initiation layer
  1. Substrate selection: Diamond (111) benchmarked against Si(111) and fused quartz for GaN heteroepitaxy.
  2. Pre-growth surface prep of diamond: Anneal / anneal-etch-anneal sequence to obtain clean (111) surface.
  3. Optional patterning (ICP or RIE): Create mesa or surface features that reduce thermal boundary resistance when bonded to GaN.
  4. AlN nucleation layer deposition: Low-temperature MOCVD AlN on diamond (111) to initiate wurtzite GaN with correct polarity.
  5. GaN buffer growth: Mid-temperature MOCVD to coalesce and relax strain on the patterned/planar diamond (111).
  6. Etch-back step: Removal of defective regions to expose a higher-quality GaN face for regrowth.
  7. GaN / AlGaN regrowth: MOCVD deposition of the active HEMT-relevant heterostructure with controlled thickness and composition.
  8. Characterization: Morphology, crystal quality, and interface structure validation prior to device processing.
  • Applicable Materials:
    • Optical / Electronic Grade SCD (single crystal diamond, 111-oriented) — directly applicable as the heteroepitaxial template referenced in this work.
    • Heavy Boron-Doped PCD — alternative where maximized lateral thermal spreading is required at larger areas than SCD allows.
    • PCD substrates up to 10 mm thickness — for robust handling during MOCVD high-temperature cycles and downstream packaging.
  • Customization Potential:
    • Orientation-specific supply: SCD (111) wafers in custom dimensions up to 125 mm (PCD) and SCD thickness range 0.1 µm - 500 µm.
    • Surface engineering support: Sub-nm polishing (Ra < 1 nm for SCD, < 5 nm for inch-size PCD) to meet the low-roughness requirement for AlN nucleation.
    • Patterning readiness: Laser-cut and patterned diamond coupons compatible with the anneal/ICP/RIE treatments described in the paper.
    • In-house metallization (Ti, W, Pt, Pd, Au, Cu): Useful for thermal bonding layers and back-side metallization stacks for HEMT packaging on diamond.
  • Engineering Support:
    • 6CCVD’s in-house PhD engineering team can assist with substrate selection (SCD vs. PCD, 111 vs. 100), doping level optimization, surface prep recipe selection, and metallization stack design for GaN-on-diamond HEMT development.
    • Consultation available for co-integrating MOCVD-grown GaN stacks with custom diamond heat spreaders and TBR-engineered interfaces.
  • Quality & Logistics:
    • Tight-tolerance thickness control, optional double-side polishing, and global DDU/DDP shipping support seamless integration into overseas MOCVD fabs and pilot lines.

For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

For most light-emitting diodes (LEDs), high power electronics and solar cells applications, gallium nitride must be deposited as a thin film on the surface of another single-crystal material. By using the periodic arrangement of surface atoms as a template, gallium and nitrogen atoms can arrange themselves to form a crystalline thin film. For LED applications in particular, silicon carbide and sapphire are the most widely used single crystal substrates because they are transparent and their atomic arrangement is symmetrically matched with that of gallium nitride. While glass is cheaper than these substrates and also transparent, it lacks a regular, uniform arrangement of its atoms. This lack of a surface template pattern means that the Ga and N atoms have no template, so GaN cannot be grown directly on its surface. In article no. 1700392, this problem is overcome by forming an ultrathin (∼30 nm) silicon layer on the glass surface. The ultrathin silicon film provides a uniformly oriented surface that acts as the template for GaN growth, while being thin enough to remain transparent. This work also demonstrates that other amorphous and mismatched substrates, such as oxidized Si(001) and polycrystalline diamond, can be used in the same manner.