Skip to content

Pressure-driven phase transitions and reduction of dimensionality in 2D silicon nanosheets

MetadataDetails
Publication Date2018-12-17
JournalNature Communications
AuthorsGil Chan Hwang, Douglas A. Blom, Thomas Vogt, Jaejun Lee, Heon‐Jin Choi
InstitutionsJilin University, University of South Carolina
Citations25
AnalysisFull AI Review Included
  • Breakthrough Discovery: The paper establishes a novel pressure-driven reduction of dimensionality, converting CVD-grown 2D silicon nanosheets (Si-NS) into 1D silicon nanowires (Si-NW) with high aspect ratios (>10).
  • Irreversible Phase Transitions: Under compression up to 21 GPa, Si-NS undergoes the sequence Si-I (cubic) → Si-II (tetragonal) → Si-V (hexagonal). Upon decompression below 8 GPa, an X-ray amorphous phase (a-Si) emerges that contains 1D nanowires.
  • Crystallite Size Dependency: Phase transition pressures are highly dependent on crystallite size. Tested samples ranged from 9.3(7) nm to 15.2(8) nm.
  • High-Purity Fabrication Route: This method bypasses traditional Au-catalyzed Vapor-Liquid-Solid (VLS) synthesis, avoiding Au contamination and SiOx layers, producing twin defects oriented along the <111> direction.
  • Thermoelectric Implications: Molecular Dynamics (MD) simulations confirm that reducing dimensionality from 2D to 1D drastically lowers thermal conductivity (&lt;100 W/mK), potentially increasing the ZT figure of merit for thermoelectric applications.
  • Methodology: Synthesis via CVD on c-plane sapphire/quartz substrates, followed by in-situ high-pressure synchrotron X-ray diffraction using a symmetric-type diamond anvil cell (SDAC).
ParameterValueUnitContext
Maximum Compression Pressure20.5 - 21.0GPaDiamond anvil cell (DAC) upper limit for Si-NS samples
Phase Transition Onset8.0GPaOnset of X-ray amorphous phase during decompression
Pressure Increments~0.5GPaStep size during compression at room temperature
Sample Equilibration Time15minHold time before XRD measurement at each pressure point
Ruby Pressure Calibration±0.05GPaPrecision of the pressure calculation
Diamond Anvil Culet Size~400µmType I diamond anvil diameter
Gasket MaterialT301 Stainless Steel-Thickness 0.25 mm, indented to 80 µm
Sample Chamber Diameter~150µmCreated via Electric Discharge Machine (EDM)
Pressure Medium (Sapphire samples)Methanol:Ethanol:Water (16:3:1)ratioHydrostatic fluid for Si-NS12.8 & Si-NS15.2
Pressure Medium (Quartz sample)Silicone Oil (10 cSt)-Hydrostatic fluid for Si-NS9.3
Crystallite Size (Si-NS15.2)15.2(8)nmDerived via Scherrer equation (λ = 0.070932(1) nm)
Crystallite Size (Si-NS12.8)12.8(8)nmIntermediate CVD growth time
Crystallite Size (Si-NS9.3)9.3(7)nmSmallest crystallite size tested
Unit Cell Volume (Ambient)0.1584 - 0.1606nm3Varies inversely with crystallite size
Si-NW Thermal Conductivity (<110>)64.5 ± 4.5W/mKSimulated (predicted by Zhou)
Si-NW Thermal Conductivity (<100>)43 ± 10W/mKSimulated (predicted by Donadio)
Si-NS Thermal Conductivity< 100W/mKUpper fluctuant range (MD simulation)
CVD Growth Temperature1273KFurnace temperature for SiCl4 bubbling
Gas Flow (H2 + Ar)300sccmInitial pre-heating flow rate
Gas Flow (High Temp)3000sccmTotal flow rate at 1273 K
SiCl4 Carrier Gas20sccmH2 bubbling rate
HAADF-STEM Voltage200kVElectron probe acceleration voltage
STEM Convergence Angle24mradSemi-angle for probe convergence
AFM Cantilever ModeTapping-Nanowizard I (JPK instruments)
  • Substrate Preparation: C-plane sapphire (for Si-NS12.8 and Si-NS15.2) and quartz (for Si-NS9.3) substrates subjected to wet cleaning before placement in the CVD furnace center.
  • CVD Nanosheet Synthesis:
    • Furnace ramped to 1273 K over 25 minutes under Ar + H2 flow (300 sccm).
    • At target temperature, flow rate increased to 3000 sccm.
    • H2 bubbled through liquid SiCl4 at 20 sccm.
    • Reaction times varied (20 min, 30 min, 45 min) to tune crystallite sizes.
  • In-Situ High-Pressure XRD: Conducted at Pohang Accelerator Laboratory (PAL) using synchrotron radiation (λ = 0.0622 or 0.0692 nm).
  • Diamond Anvil Cell Loading: Samples sealed in T301 gaskets with hydrostatic pressure media. Ruby chips (&gt;40 µm) used for pressure calibration via R1 emission line shift.
  • HAADF-STEM Imaging: Samples meticulously cleaned with hexane to remove silicone oil residue prior to loading on holey carbon-coated copper grids to prevent beam degradation.
  • Molecular Dynamics Simulation: Equilibrium MD (EMD) using the Tersoff potential in LAMMPS. Models constructed for bulk Si, Si-NS (free boundaries along x), and Si-NW (free boundaries along x and y, periodic along z &lt;111&gt;).
  • Crystallite Size Calculation: Scherrer equation applied to the (111) reflection peak width, subtracting instrumental broadening (SRM LaB6 660c).

While this research focuses on silicon, the high-pressure diamond anvil cell (DAC) methodology and subsequent structural characterization techniques rely heavily on high-quality single crystal and polycrystalline diamond components. 6CCVD is uniquely positioned to support the engineering demands of this advanced materials research.

  • Applicable Materials:
    • Optical Grade Single Crystal Diamond (SCD): Essential for the diamond anvils (type I) used in this experiment. 6CCVD provides optical-grade SCD plates and wafers capable of withstanding extreme multi-anvil pressures (&gt;21 GPa).
    • Polycrystalline Diamond (PCD): Used as robust backing seats and gasket reinforcement materials for high-pressure synchrotron beamline applications.
    • Heavy Boron-Doped PCD (BDD): Suitable for conductive components within the high-pressure electrical measurement cells if this experiment were extended to monitor resistivity changes during the I → II → V phase transition sequence.
  • Customization Potential:
    • The paper utilized a standard ~400 µm culet diamond anvil. For researchers looking to vary pressure geometry, increase culet sizes for larger sample chambers, or develop novel DAC designs, 6CCVD offers custom diamond dimensions up to 125mm.
    • Custom Metalization: If the diamond anvils require integrated heating elements or electrode connections for in-situ conductivity studies during decompression (e.g., monitoring the amorphous phase recovery), 6CCVD offers internal Au, Pt, Pd, Ti, W, and Cu metalization.
    • Laser Cutting & Shaping: To achieve specific anvil geometries or culet profiles beyond standard cuts, 6CCVD provides precision laser shaping services.
  • Engineering Support:
    • The transition from bulk silicon to 2D Si-NS, and subsequently to 1D Si-NW requires ultra-precise pressure calibration and flawless diamond interfaces to avoid gasket blow-outs.
    • 6CCVD’s in-house PhD engineering team can assist with material selection for high-pressure physics research, ensuring that the chosen SCD or PCD component possesses the required Raman spectroscopic purity, lack of internal twinning, and optimal thermal conductivity to maintain stable hydrostatic conditions.
  • Quality Assurance:
    • With surface polishing capabilities down to Ra &lt; 1nm (SCD) and &lt; 5nm (PCD), 6CCVD components ensure perfect sealing against the T301 stainless-steel gaskets, minimizing pressure leaks during the 15-minute equilibration periods required by this protocol.
  • Call to Action:
    • For custom specifications, specialized anvil geometries, or material consultation regarding diamond components for high-pressure physics and X-ray diffraction projects, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract

In-situ high-pressure synchrotron X-ray powder diffraction studies up to 21 GPa of CVD-grown silicon 2D-nanosheets establish that the structural phase transitions depend on size and shape. For sizes between 9.3(7) nm and 15.2(8) nm we observe an irreversible phase transition sequence from I (cubic) → II (tetragonal) → V (hexagonal) during pressure increase and during decompression below 8 GPa the emergence of an X-ray amorphous phase. High-angle annular dark field scanning transmission electron microscopy (HAADF-STEM) and atomic force microscopy (AFM) images of this X-ray amorphous phase reveal the formation of significant numbers of 1D nanowires with aspect ratios > 10, which are twinned and grow along the <111> direction. We discovered a reduction of dimensionality under pressure from a 2D morphology to a 1D wire in a material with a diamond structure. MD simulations indicate the reduction of thermal conductivity in such nanowires.