Skip to content

Fabrication of boron doped diamond cantilevers by means of dry ICP etching

MetadataDetails
Publication Date2019-09-01
JournalJournal of Physics Conference Series
AuthorsMarián Vojs, Marián Marton, M. Janco, Miroslav Behúl, V. Řeháček
InstitutionsInternational Laser Center, Slovak University of Technology in Bratislava
Citations1
AnalysisFull AI Review Included
  • Core Goal: Fabrication of Boron-Doped Diamond (BDD) cantilevers for highly sensitive MEMS sensor applications (biological, gas, DNA detection).
  • Primary Innovation: A purely dry-fabrication process (no wet chemical etching of the Si substrate) utilizing Aluminum (Al) masking and SF6/O2 plasma in an Inductively Coupled Plasma Reactive Ion Etching (ICP RIE) system.
  • Material Used: Highly Boron-Doped Polycrystalline Diamond (BDD) thin films (~450 nm thick) deposited via Plasma-Enhanced Hot Filament CVD (PE-HFCVD).
  • Process Specifics: A 3-step sequential etch recipe combining anisotropic (high bias) and isotropic (low bias) profiles to release the cantilevers.
  • Performance Achievement: Successfully manufactured defect-free, 5 µm wide BDD cantilevers exhibiting multiple resonance modes, with primary peaks measured at 22.2 kHz and 65.6 kHz, and measurable sensitivity up to 146.8 kHz.
  • Key Advantage: Utilizes diamond’s intrinsic properties—wide band gap, low dielectric constant, and high carrier mobility—for superior sensor performance compared to standard silicon.
ParameterValueUnitContext
Diamond Film Thickness~450nmMeasured via SEM
Substrate Size10 x 10mmSilicon (Si) substrate
Boron Doping Ratio10,000ppm (B/C)Achieved using Trimethylboron
Carbon Source Ratio1% CH4 in H2Atmosphere composition
Deposition Temperature650°CSubstrate temperature during PE-HFCVD
Chamber Pressure3,000PaDeposition pressure
Deposition Time120minTotal time per film
Etch Mask MaterialAluminum (Al)nmMask thickness: 200 nm
Cantilever Widths Tested1, 3, 5, 10, 15µmPhotolithography strip pattern
Cantilever Length30µmStandard strip length
Primary Resonant Frequency 122.2kHzMode M1 (5 µm width)
Primary Resonant Frequency 265.6kHzMode M4 (5 µm width)
Max Measurable Frequency146.8kHzUpper limit of MEMS sensitivity
Acoustic Activation Range> 200kHzExcitation frequency range
  • Substrate Preparation: Silicon (Si) substrates (10x10 mm2) seeded in a diamond nanoparticle solution (≤10 nm size) using an ultrasonic bath for 40 min to promote nucleation.
  • Chemical Vapor Deposition: BDD films grown via Plasma-Enhanced Hot Filament CVD (PE-HFCVD) with a CH4/H2 atmosphere doped with Trimethylboron.
  • Masking: 200 nm thick Aluminum (Al) layer deposited and patterned via standard photolithography to define the cantilever strip widths (1-15 µm).
  • Dry Etching (ICP RIE): A 3-step plasma etching sequence using SF6/O2 gas mixtures (detailed below).
  • Characterization: Morphology and structure analyzed via Scanning Electron Microscopy (SEM); vibrational properties measured using a Polytec OFV 303 laser vibrometer and digital oscilloscope.
StepTypeSF6 (sccm)O2 (sccm)ICP Power (W)RF Power (W)VBias (V)Pressure (mTorr)Time (min)
1Anisotropic (BDD Etch)100102,000300590102
2Anisotropic (Si Deepen)80202,00010551015
3Isotropic (Si Release)8002,0005301025

The research detailed in this paper requires ultra-thin, highly doped polycrystalline diamond films capable of withstanding high-energy plasma environments without delamination. Below is how 6CCVD’s capabilities directly align with replicating or extending this MEMS research:

  • Applicable Materials:

    • Heavy Boron-Doped PCD: To replicate the conductive BDD films used here (10,000 ppm B/C ratio), 6CCVD supplies highly customized Boron-Doped Polycrystalline Diamond. Our heavy doping capabilities provide the exact electrical conductivity required for electrochemical analyte deposition described in the paper.
    • Optical Grade PCD: For projects where surface roughness is critical for resonance stability, our PCD can be polished to Ra < 5 nm on inch-size wafers, providing an ideal foundation for micro-fabrication.
  • Customization Potential:

    • Substrate & Thickness Versatility: While the paper used 10x10 mm2 substrates, 6CCVD specializes in custom dimensions for PCD plates/wafers up to 125mm. Our standard thickness range (0.1 µm - 500 µm) perfectly accommodates the sub-micron film requirements (450 nm) necessary for MEMS fabrication.
    • Metalization Services: We recognize the critical role of the etching mask. 6CCVD provides in-house metalization services (Au, Pt, Pd, Ti, W, Cu). If the research requires transitioning from an Al mask to a more robust interface for direct wire bonding or electrical contacts, our engineering team can deposit custom metal stacks (e.g., Ti/Pt/Au) tailored to your exact specifications.
    • Laser Cutting: To achieve the 1 µm to 15 µm cantilever widths discussed, precise edge geometry is vital. 6CCVD offers laser cutting services to define exact geometries without inducing micro-cracks in the diamond lattice.
  • Engineering Support:

    • Diamond MEMS and sensor arrays require precise tuning of residual stress, doping gradients, and surface morphology. The in-house PhD team at 6CCVD is equipped to assist with material selection for advanced MEMS, NEMS, and electrochemical sensor projects, ensuring the diamond substrate meets your specific resonance frequency and mass-loading requirements.
  • Call to Action:

    • For custom specifications, heavy doping consultations, or material selection for your next MEMS fabrication cycle, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract

Abstract This paper is focused on the preparation of boron doped diamond (BDD) cantilevers for MEMS applications. Hot filament CVD diamond deposition technique was used for preparation of highly boron doped thin film. The fabrication process consisted only of dry etching steps and masking process, no wet etching of substrate was used. Therefore, it was necessary to optimize both anisotropic and isotropic etching to release the cantilever structure from silicon substrate. Doped diamond cantilevers were etched by reactive ion etching using inductively coupled plasma (ICP RIE) through aluminum etching masks. The optimal properties of fabrication process led to high quality MEMS structures. The resulting cantilevers were investigated by scanning electron microscopy (SEM) and laser vibrometer system. Finally, we demonstrate a BDD cantilever (5 μm width) with the main resonant frequencies at 22.2 kHz, 46.6 kHz, 52.2 kHz and 65.6 kHz.