Fluid Flow Analysis of Agitation Pipe in the Electroplated Diamond Wire Saw
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2021-11-01 |
| Journal | Journal of Physics Conference Series |
| Authors | Derong Duan, GE Pei-qi, Zhigang Gong, Fuli Huang, Guangzhou Cao |
| Institutions | Shandong University, University of Jinan |
| Analysis | Full AI Review Included |
Executive Summary
Section titled “Executive Summary”- Core Focus: Computational Fluid Dynamics (CFD) analysis of agitation pipe designs used in the electroplated diamond wire saw manufacturing process for slicing hard-brittle materials.
- Industrial Context: Targets the semiconductor and photovoltaic industries, specifically the slicing of monocrystalline and polycrystalline silicon where IC line widths are scaling down to 0.1 mm.
- Key Variable 1 (Structure): The central water inlet type agitation pipe outperformed end-inlet configurations, generating a flow field with high velocity in the middle and lower velocity on both sides.
- Key Variable 2 (Angle): Sandblasting angle performance ranking: 30° > 45° > 60°.
- Key Variable 3 (Diameter): A tapered configuration (7.5 mm front, 7 mm middle, 7.5 mm rear) delivered the most uniform momentum distribution across the 24 outlets.
- Outcome: Optimized fluid dispersion directly improves the homogeneous suspension of diamond fine powder, a critical factor in saw wire quality and slicing yield.
- Method: Comparative simulation of fluid velocity and momentum profiles across multiple agitation pipe geometries.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Target Materials | Monocrystalline & Polycrystalline Silicon | — | Primary workpiece for IC/photovoltaic |
| IC Line Width Range | 0.18 down to 0.1 | mm | Driving precision requirement |
| Total Sandblasting Outlets | 24 | ports | Per agitation pipe |
| Outlet Grouping | 3 sections (I 1-3, I 4-9, I 10-12) × 2 sides | — | Spatial layout of nozzles |
| Evaluated Sandblasting Angles | 30°, 45°, 60° | degrees | Inclination of nozzle ports |
| Average Fluid Velocity (Angle Test) | 3.85 - 3.93 | m/s | Across all angle configurations |
| Minimum Fluid Velocity | 3.52 (60° case) | m/s | Lowest recorded at nozzle |
| Maximum Fluid Velocity | 4.05 (45° case) | m/s | Highest recorded at nozzle |
| Outlet Diameter (Structure A) | 7.0 | mm | Uniform diameter baseline |
| Outlet Diameter (Structure B) | 8.0 (ends), 7.0 (middle) | mm | Overcompensated ends |
| Outlet Diameter (Structure C) | 7.5 (ends), 7.0 (middle) | mm | Optimal tapered design |
| Mean Momentum Range | 0.56 - 0.59 | kg·m/s | Across all diameter configurations |
| Min Momentum Difference (Structure A) | 5.80% | — | Front-to-rear variation |
| Max Momentum Difference (Structure B) | -21.91% | — | Overcompensation penalty |
| Max Abs. Momentum Difference (Structure C) | 6.09% | — | Optimal uniformity achieved |
| Std. Deviation of Momentum | 0.029 - 0.063 | — | Structure B shows highest dispersion |
Key Methodologies
Section titled “Key Methodologies”- Process Domain: Suspension composite electroplating line for manufacturing diamond wire saws (one-machine-multi-wire configuration).
- Simulation Tool: Fluid dynamics software for evaluating velocity and momentum fields inside the agitation pipe.
- Step 1 — Structure Comparison: Tested central water inlet vs. end-inlet pipe geometries to map fluid distribution profiles.
- Step 2 — Angle Sweep: Varied sandblasting nozzle inclination at 30°, 45°, and 60° while measuring exit velocity at all 24 ports.
- Step 3 — Diameter Optimization: Fixed nozzle angle at 45° and tested three diameter schemes (A: uniform 7 mm, B: 8 mm ends/7 mm middle, C: 7.5 mm ends/7 mm middle).
- Step 4 — Momentum Mapping: Quantified jet momentum per nozzle section (No. 1-4, 5-8, 9-12) to calculate relative deviation across the pipe length.
- Step 5 — Selection Criterion: Chose the geometry that minimized relative change in momentum between front, middle, and rear nozzle groups.
- Key Finding: Structure C (tapered 7.5/7/7.5 mm) at 30°-45° delivers the highest mixing degree in the upper sand tank.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”-
Applicable Materials:
- For wire saw manufacturing and slicing-tool R&D, our Optical Grade Single Crystal Diamond (SCD) substrates (available 0.1 µm - 500 µm thickness) serve as ideal reference flats for kerf-loss and surface-roughness metrology on sliced silicon wafers.
- For wear components exposed to abrasive slurry in agitation systems (nozzles, guide rollers, mixing impellers), our Polycrystalline Diamond (PCD) plates — up to 125 mm diameter — provide extreme abrasion resistance that can extend service life in sand-suspension environments.
- For electrical contact or sensor elements within the plating bath, our Boron-Doped Diamond (BDD) offers chemical inertness in acidic nickel electroplating baths used in composite electroplating.
-
Customization Potential:
- 6CCVD provides custom laser cutting to produce PCD wear plates or nozzles in non-standard geometries — directly applicable to the optimized 7.5/7/7.5 mm tapered port configurations identified in this study.
- In-house metallization (Au, Pt, Pd, Ti, W, Cu) is available for diamond components requiring electrode integration or corrosion-resistant coatings in wet slurry environments.
- Custom thicknesses from 0.1 µm to 10 mm allow tailoring of nozzle inserts, bearing sleeves, and guide surfaces for precision wire-saw machinery.
-
Engineering Support:
- 6CCVD’s in-house PhD engineering team can assist with material selection for components in diamond wire saw manufacturing equipment, slurry-handling systems, and downstream silicon wafer processing.
- We support R&D teams working on next-generation slicing and dicing equipment, including optimized fluid-delivery subsystems and wear-resistant contact surfaces.
-
Call to Action: For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
Abstract Agitation pipe is the important part of the electroplated diamond wire saw in the suspension sanding process. The structure type and the sandblasting configuration in agitation pipe play a role on the flow uniformity. Fluid flow in the different structure forms of agitating pipe was studied and the influence of sandblasting angle and the diameter was also contrasted. Results found that the central water type of agitation pipe has the better performance, generating the flow field distribution in the middle part with high velocity and small velocity on both sides. The order of sandblasting in performance was 30°, 45° and 60°. The better flow uniformity occurred in the configuration of sandblasting with the diameter 7.5 mm, 7 mm and 7.5 mm.
Tech Support
Section titled “Tech Support”Original Source
Section titled “Original Source”References
Section titled “References”- 2007 - Hard inclusions and their detrimental effects on the wire sawing process of multicrystalline silicon [Crossref]
- 2015 - Application and development of wafer slicing technology
- 2020 - Simulational and experimental studies on flow rates at the blow holes of bath agitation pipe during composite electroplating for manufacturing of diamond wire saws
- 2017 - Effect of the weight of nickel coated on diamond surface on performance of electroplated diamond wire saw
- 2019 - Experimental analysis on sawing performance of sand-suspension-electroplated wire saw