Skip to content

Quantum Imaging of Ferromagnetic van der Waals Magnetic Domain Structures at Ambient Conditions

MetadataDetails
Publication Date2025-11-06
JournalACS Applied Materials & Interfaces
AuthorsBindu, Amandeep Singh, Amir Hen, Lukas Cavar, Sebastian Maria Ulrich Schultheis
InstitutionsApplied Nanotech (United States), Johannes Gutenberg University Mainz
AnalysisFull AI Review Included
  • Method: NV-center wide-field quantum diamond microscopy (QDM) and scanning-NV magnetometry (SNVM) used for ambient-condition, non-invasive imaging of 2D van der Waals ferromagnet Fe5−xGeTe2 (FGT).
  • Key Result 1: Direct sub-micrometer imaging of magnetic domains and magnetization (Mz) in exfoliated FGT flakes (15-221 nm) confirms robust near-room-temperature ferromagnetism.
  • Key Result 2: Curie temperature (TC) is essentially thickness-independent in the 15-221 nm range; TC spans 285 K - 315 K, indicating interfacial/anisotropy effects are not dominant in this regime.
  • Key Result 3: Identification of previously unknown “stripe” magnetic/crystallographic features correlated with Fe/Ge/O concentration modulations from synthesis and differential oxidation.
  • Quantitative Output: Magnetization variance ΔB2norm vs T fitting yields TC = 296.6 ± 1.5 K (221 nm flake) and 295 ± 2.1 K (15 nm flake); bulk crystal TC = 305.5 ± 2.5 K.
  • Sensitivity Achieved: QDM magnetic sensitivity η = 172.3 ± 6.8 nT/√Hz with stray-field resolution down to a few µT at ≈20 nm stand-off.
  • Application Impact: Validates FGT as a viable material candidate for room-temperature spintronic, magnetic memory, and logic devices based on 2D vdW heterostructures.
ParameterValueUnitContext
Diamond substrate dimensions3 × 3 × 0.1mmElement Six electronic-grade single crystal
Diamond crystallographic cut{100}planePerpendicular to x-axis; equal projections on 4 NV axes
NV ensemble depth~20nmBelow diamond surface
Nitrogen ion (N15) implantation dose2 × 1013cm−210 keV energy
NV ground-state ZFS Dgs2.87GHzZero-field splitting
NV excited-state ZFS Des1.42GHzExcited-state splitting
Green laser initialization wavelength532nmOptical pumping
NV zero-phonon line637nmCharacteristic fluorescence
Bias magnetic field (Helmholtz)30-35Gauss (≈3000-3500 µT)z-direction
Typical experimental bias field1800 / 3150µTQDM imaging of FGT
Zeeman splittingΔ = 2γB∥GHzWhere γ is electronic gyromagnetic ratio
Microwave controlCoplanar waveguide—Drives
Peltier temperature range278 - 328K±0.1 K precision
Pixel size (camera + binning)≈300nmDiffraction limit ~λ/2NA
Objectives used40× / 60× / 100×magnificationNA = 0.65 / 0.95
CameraAndor Neo 5.5 sCMOS—2560 × 2160 (5.5 MP)
Magnetic sensitivity η172.3 ± 6.8nT/√HzDemonstrated ODMR limit
Stray field at 20 nm stand-off~250µTFerromagnetic domains at low T
Curie temperature (221 nm flake)296.6 ± 1.5KPower-law fit exponent γ = 1.78
Curie temperature (15 nm flake)295 ± 2.1KPower-law fit exponent γ = 1.48
Curie temperature (bulk crystal)305.5 ± 2.5KWeiss constant from Curie-Weiss fit
FGT flake thickness range15 - 221nmExfoliated flakes
Average domain width (bulk, 50 K, XPEEM)≈250nmReference benchmark
Stripe spacing in FGT2 - 3µm~60° orientation to horizontal
Stripe surface depression (SNVM)3 - 5nmAFM line-cut
Stripe surface depression (post-SEM)~10nmEnhanced by e-beam exposure
SQUID measurement field100OerstedZFC bulk measurement
FGT encapsulation~5nmAu or Pt against oxidation
Cr/Au marker thickness10 / 100nmDiamond locator markers
  • Diamond NV-engineering: Electronic-grade {100} SCD implanted with N15 at 2 × 1013 cm−2, 10 keV; followed by high-temperature annealing and electron irradiation to form an NV ensemble ≈20 nm below the surface.
  • Sample preparation (glove-box, <5 ppm O2/H2O): Mechanical exfoliation of Fe5−xGeTe2 (x ≈ 0.3) bulk single crystal using silicone-free tape; iterative thinning by tape re-adherence; transfer by stamping onto the diamond surface; deposition of 10 nm Cr / 100 nm Au markers via photolithography for optical navigation.
  • Oxidation protection: Thin flakes (<20 nm) encapsulated with ≈5 nm Au or Pt via in-glove-box evaporator.
  • QDM optical train: 532 nm green laser for spin initialization; 637-800 nm fluorescence collection; 40× (NA 0.65) and 60× (NA 0.95) air objectives; defocusing lens; dichroic mirror; Andor Neo 5.5 sCMOS with pixel binning.
  • Microwave delivery: Coplanar waveguide delivering MWs to drive |0⟩ ↔ |±1⟩ transitions; ODMR measured pixel-wise for spatial field maps.
  • Bias field and geometry: 30-35 Gauss (1800-3150 µT) along NV axis with B∥ = Bextz · cos(54.75°); Helmholtz coils; z-oriented projection equal across four NV axes.
  • Temperature control: Peltier cooler (Lightwave LDT-5910B) with 14.184 kΩ thermistor feedback, ±0.1 K stability across 278 - 328 K.
  • SNVM (scanning-NV mode): QZabre QSM with commercial diamond NV tip; tuning-fork amplitude-modulated AFM feedback in contact mode (standoff <100 nm); tip temperature 25 ± 0.05 °C; vector magnet for biasing; ODMR tracked per pixel.
  • Bulk reference TC: Quantum Design SQUID magnetometry under 100 Oe after zero-field cooling; Curie-Weiss fit yielding Weiss constant.
  • Magnetic image reconstruction: Pixel-wise ODMR → 2D Bz map → reverse-propagation algorithm to reconstruct 2D Mz distribution.
  • Phase-transition extraction: Compute normalized stray-field variance ΔB2norm = (ΔB2flk − ΔB2bkg)/norm; fit to α + β(1 − T/TC)γ.
  • Crystallographic analysis: SEM (10 keV, 5000-8000×), 5 keV EDXS line scans (40 points over 16.64 µm), AFM tapping-mode topography; 2D and angle-resolved 1D autocorrelation of magnetic images to quantify stripe periodicity.
Research RequirementRecommended 6CCVD Material
Electronic-grade {100} SCD substrate for shallow NV ensemble (~20 nm)Optical / Electronic Grade SCD, custom cut along {100} plane, 0.1-500 µm thickness, Ra < 1 nm polish
Implantation-ready, low-strain, high-uniformity diamond windowsOptical Grade SCD (multi-mm); custom laser-cut coupons to 3 × 3 mm or larger wafer formats up to 125 mm
Bulk diamond reference / high-pressure anvils for complementary SQUID-NV comparisonSubstrate-grade PCD up to 10 mm thickness
Possible future conductive-diamond components (heaters, electrodes, patterned films)Boron-Doped PCD (BDD) with tunable resistivity
  • Custom crystallographic orientation: 6CCVD can supply SCD substrates cut along {100}, {110}, or {111} — the {100} orientation used here is critical for symmetric NV axis projection and uniform bias-field response.
  • Custom NV-engineered substrates: While ion implantation is typically performed by the end-user or via partner labs, 6CCVD can provide as-grown nitrogen-containing SCD or ultra-low-nitrogen electronic-grade SCD as starting material, and can coordinate thickness/polish specifications (down to Ra < 1 nm) optimized for near-surface NV sensitivity.
  • Custom metallization for markers and electrical contacts: The 10 nm Cr / 100 nm Au fiducial markers and Au/Pt encapsulation layers used in this work fall directly within 6CCVD’s internal Au, Pt, Pd, Ti, W, Cu metallization capability — including Ti/Au, Cr/Au, and Pt capping stacks.
  • Laser cutting and patterning: 6CCVD’s precision laser-cutting service can deliver the small 3 × 3 mm diamond coupons used as QDM sensors, plus dicing of PCD/SCD wafers into application-specific geometries without chipping.
  • Thickness engineering: For both the diamond substrate (down to 100 µm and below) and any protective capping layers (Au/Pt 5-10 nm), 6CCVD supports tight thickness tolerances required for reproducible NV stand-off distance and stray-field calibration.
  • Surface polishing: Ra < 1 nm SCD polish is essential to maintain the ≈20 nm NV depth uniformity and reproducible flake transfer; 6CCVD’s sub-nm polishing ensures clean, flat surfaces for vdW flake stamping.
  • 6CCVD’s in-house PhD team can assist with material selection for NV-magnetometry, quantum-sensing, and 2D vdW spintronics projects — including guidance on optimal crystal orientation, NV-layer geometry, surface termination, and capping/encapsulation metallization schemes for oxidation-sensitive materials such as Fe5−xGeTe2.
  • Consultation available on diamond-vdW heterostructure integration, including polishing protocols compatible with mechanical exfoliation, and on metallization stack design (adhesion layer + functional layer + capping layer) for marker patterning and in-situ electrical biasing.
  • 6CCVD can also support high-purity custom crystal growth for novel magnetic vdW substrates and provide matched PCD reference samples for cryogenic/SQUID cross-calibration experiments.

For custom specifications, metallization stacks, or material consultation on diamond substrates for quantum magnetic microscopy and 2D spintronics, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

High Resolution Image Download MS PowerPoint Slide Recently discovered 2D van der Waals magnetic materials, and specifically iron-germanium-telluride (Fe 5 GeTe 2 ), have attracted significant attention both from a fundamental perspective and for potential applications. Key open questions concern their domain structure and magnetic phase transition temperature as a function of sample thickness and external field, as well as implications for integration into devices such as magnetic memories and logic. Here we address key questions using a nitrogen-vacancy center based quantum magnetic microscope, enabling direct imaging of the magnetization of Fe 5 GeTe 2 at submicrometer spatial resolution as a function of temperature, magnetic field, and thickness. This quantum imaging technique provides noninvasive, high-sensitivity measurements with high spatial resolution under ambient conditions, making it particularly well suited for probing 2D magnets. We employ spatially resolved measures, including magnetization variance and cross-correlation, and find a significant spread in transition temperature yet with no clear dependence on thickness down to 15 nm. We also identify previously unknown stripe features in the optical as well as magnetic images, which we attribute to modulations of the constituting elements during crystal synthesis and subsequent oxidation. Our results suggest that the magnetic anisotropy in this material does not play a crucial role in their magnetic properties, leading to a magnetic phase transition of Fe 5 GeTe 2 which is largely thickness-independent down to 15 nm. Our findings could be significant in designing future spintronic devices, magnetic memories, and logic with 2D van der Waals magnetic materials.