Skip to content

Sensing Electric Currents in an a‐IGZO TFT‐Based Circuit Using a Quantum Diamond Microscope

MetadataDetails
Publication Date2025-11-08
JournalAdvanced Materials Technologies
AuthorsMD Shahrukh Adnan Khan, Pralekh Dubey, L. P., Ashutosh Tripathi, Phani Peddibhotla
InstitutionsIndian Institute of Science Education and Research, Bhopal, Indian Institute of Technology Kanpur
AnalysisFull AI Review Included

Quantum Diamond Microscope (QDM) Current Sensing in Flexible a-IGZO TFT Circuits: Technical Analysis & Material Integration

Section titled “Quantum Diamond Microscope (QDM) Current Sensing in Flexible a-IGZO TFT Circuits: Technical Analysis & Material Integration”
  • Core Achievement: Demonstration of room-temperature, non-invasive 2D current density mapping in an a-IGZO TFT current mirror circuit using NV-center diamond magnetometry, bypassing conventional electrical probing limitations.
  • Sensor Architecture: Utilization of a single-crystal CVD diamond sensor (2 mm × 2 mm × 0.5 mm) featuring a [110] edge orientation, [100] front facet, and a ~2.5 µm isotopically purified [12C] NV layer (~1 ppm NV concentration).
  • Measurement Precision: Current extraction demonstrated a 1.2% error relative to conventional probing in accessible regions (Region A: 755.2 µA vs 746.1 µA) and 0.68% versus simulation.
  • Internal Path Sensing: Detected current in Region B (268.2 µA vs 300 µA theoretical, 10.6% error) — an internal conducting path physically inaccessible due to the 80 nm Al2O3 passivation layer.
  • Proximity Engineering: Achieved ultra-low stand-off distances between the NV layer and circuit traces of hA = 2.3 µm and hB = 2.8 µm via direct diamond placement on the DUT.
  • ODMR Methodology: Employed Projective Magnetic Microscopy (PMM) via ODMR with a 2 mT NdFeB bias field aligned to the [111] NV axis, utilizing 532 nm laser excitation and Zeeman splitting analysis.
  • Validation: Confirmed vector current density components (Kx, Ky) and reconstructed magnitude profiles from inverse Biot-Savart transformation in Fourier space.
ParameterValueUnitContext
Diamond Sensor Dimensions2 × 2 × 0.5mmSingle-crystal CVD sensor chip
Diamond Edge Orientation[110]—Crystallographic axis
Diamond Front Facet[100]—Crystallographic plane
NV Layer Thickness~2.5µmIsotopically purified [12C]
NV Concentration~1ppmDefect density
Stand-off Distance (Region A)2.3µmSensor-to-trace gap
Stand-off Distance (Region B)2.8µmSensor-to-trace gap
Bias Magnetic Field~2mTNdFeB permanent magnet
Bias Field Alignment[111]—NV symmetry axis orientation
NV Gyromagnetic Ratio28MHz/mTSpin response constant
Zero-Field Splitting (D)2870MHzNV ground-state resonance
Laser Excitation532nmGreen laser source
Laser Spot Size30µmFocused via 40× 0.55 NA objective
Fluorescence Collection650 longpass / 637-800 emissionnmFilter and emission band
Optical Resolution (Effective)260 × 260nm2Post-binning pixel size
ODMR Frequency Points71stepsPer MW sweep
Dwell Time10msPer frequency step
Averaging Cycles~110repetitionsSNR enhancement
Total Acquisition Time~10minutesFull measurement sequence
a-IGZO TFT Mobility8.8 ± 0.05cm2/VsField-effect mobility
TFT Turn-on Voltage-1.6 ± 0.4VSwitching threshold
Subthreshold Swing300 ± 40mV/decSwitching sharpness
Gate Leakage<1pAOff-state current floor
ON/OFF Ratio>108—Switching dynamic range
Current Mirror Ratio14.92—M2 (4800/20) vs M1 (320/20)
Current (Region A)755.2µAQDM-reconstructed current
Current (Region B)268.2µAQDM-reconstructed internal path
Current Density (Region A)79.5 ± 0.5A/mMean magnitude
Current Density (Region B)17.3 ± 0.2A/mMean magnitude
Trace Width (Region A)~9.5µmConductive path width
Trace Width (Region B)~15.5µmConductive path width
Passivation Layer80nmAl2O3 thickness
Max Process Temperature150°CCompatible with flexible PEN
  1. Sensor Fabrication: Single-crystal CVD diamond substrate (2 mm × 2 mm × 0.5 mm) with [110] edges and [100] facet, overgrown with ~2.5 µm isotopically purified [12C] layer containing ~1 ppm NV centers.
  2. DUT Preparation: a-IGZO TFT current mirror circuit with 16 TFTs (1 input + 15 parallel output) fabricated on 125 µm PEN substrate bonded to Eagle XG glass via 100 nm Al2O3 buffer and thermally sensitive adhesive.
  3. Sputter Deposition: 25 nm IGZO (1:1:1 In:Ga:Zn ratio) deposited under Ar at 1 mTorr; 100 nm Mo-Cr (10% Cr) for gate and source/drain electrodes.
  4. ALD Passivation: 80 nm Al2O3 layers deposited at 150 °C for gate insulator and passivation.
  5. Sensor Placement: Diamond placed directly on DUT with NV layer in physical contact with the current-carrying traces; piezo-based nanopositioner for region-of-interest alignment.
  6. Optical Excitation: 532 nm laser focused through 40× 0.55 NA air objective (30 µm spot diameter) onto NV layer.
  7. Microwave Delivery: CW MWs (Keysight N5171B + ZHL-16W-43-S+ amplifier) delivered via custom loop antenna (1 mm copper wire) positioned immediately above diamond-DUT interface.
  8. ODMR Spectroscopy: PMM technique with 71-point MW frequency sweeps (±10 ms dwell); ~110 averaging cycles; two-dip Lorentzian fitting to resolve 15N hyperfine splitting.
  9. Magnetic Field Extraction: BNV = (f+ - f-) / (2γNV) computed per pixel; Bbias subtracted to isolate current-induced Oersted field.
  10. Current Density Reconstruction: Inverse Biot-Savart transformation in Fourier space (Roth et al. method) with 2.5 µm NV layer thickness averaging correction.
  11. Stand-off Fitting: Biot-Savart analytical model (Eq. 6) fitted to magnetic field linecuts to extract hA = 2.3 µm and hB = 2.8 µm.

The experimental protocol detailed in this paper aligns directly with 6CCVD’s manufacturing portfolio. The following sections outline how our standard and custom offerings can support replication or extension of this quantum sensing research.

  • Optical Grade Single-Crystal Diamond (SCD): The sensor substrate described — [110] edge / [100] front facet, 2 mm × 2 mm × 0.5 mm — falls squarely within our standard SCD geometry offering. We supply SCD substrates polished to Ra <1 nm on the front facet, ensuring minimal optical scatter during PL collection. Larger plates and wafers up to 125 mm are also available for wafer-scale QDM development.
  • Isotopically Engineered NV-Doped SCD: The ~2.5 µm [12C]-enriched NV layer (~1 ppm) can be produced via CVD overgrowth on our high-purity SCD substrates. We offer custom NV concentration tuning (sub-ppm to >10 ppm) and [12C] enrichment grades >99.99% to extend coherence times for higher-sensitivity magnetometry.
  • Polycrystalline Diamond (PCD) Alternative: For cost-sensitive or large-area prototype development, our free-standing PCD plates (polished to Ra <5 nm at inch-scale) can serve as drop-in sensor substrates for initial system calibration before transitioning to SCD.
  • Non-Standard Sensor Geometries: The paper specifies a 2 mm × 2 mm footprint. 6CCVD routinely delivers laser-cut custom SCD and PCD shapes to ±25 µm tolerance; we can replicate this geometry or scale it up to 10 mm × 10 mm single-crystal sensors for wider field-of-view QDM designs.
  • Thickness Control: Our SCD thickness range spans 0.1 µm - 500 µm, with the 500 µm substrate thickness used here available as a standard catalog item. Thinner sensors (down to 0.1 µm) are feasible for reduced stand-off distance in next-generation scanning probe geometries.
  • Custom Metalization: While this paper employs an MW loop antenna positioned externally, researchers pursuing monolithic integration (e.g., on-chip MW stripline or coplanar waveguide) can leverage our in-house metalization capabilities with Au, Pt, Pd, Ti, W, or Cu. Ti/Pt/Au multilayer stacks are recommended for biocompatible or wire-bondable contact pads.
  • Surface Engineering: For ultra-low stand-off targeting (h < 2 µm), our sub-nanometer polishing service (Ra <1 nm SCD) combined with precision laser cutting minimizes edge bead and surface non-uniformity that would otherwise increase sensor-to-trace gap.
  • PhD-Level Consultation: Our in-house PhD engineering team can advise on material selection across the full QDM sensor stack — from substrate crystallographic orientation ([100] vs [110] vs [111]) to NV layer overgrowth parameters, isotope enrichment strategy, and metalization scheme compatibility with your readout electronics.
  • Wafer-Scale Inspection: For researchers scaling this protocol toward full-wafer oxide-TFT or emerging semiconductor diagnostics, we supply SCD wafers up to 125 mm and PCD substrates up to 10 mm thick, enabling parallel sensor fabrication for multi-DUT inspection platforms.
  • Application-Specific Guidance: Whether your focus is flexible electronics yield improvement, failure analysis in oxide TFTs, or extension to SiC/GaN power device diagnostics, our team can recommend the optimal diamond grade (SCD vs PCD), doping strategy (Boron-Doped Diamond available for electrostatic discharge protection in harsh-environment variants), and surface finish to match your optical and proximity constraints.

For custom specifications, isotope-enriched NV layer overgrowth, or material consultation on quantum sensing and emerging semiconductor diagnostic projects, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

Abstract The Quantum Diamond Microscope (QDM) is an emerging magnetic imaging tool enabling noninvasive characterization of electronic circuits through spatially mapping current densities. In this work, wafer‐level current sensing is demonstrated for a current mirror circuit composed of 16 amorphous‐ indium‐gallium‐zinc oxide (a‐IGZO) thin‐film transistors (TFTs). a‐IGZO TFTs are promising for flexible electronics due to their high performance. Using QDM, 2D magnetic field images produced by DC currents were obtained, from which accurate current density maps are extracted. Notably, QDM measurements agree well with conventional electrical probe station measurements, and enable current sensing in internal circuit paths inaccessible via conventional electrical probing techniques. The results highlight QDM’s capability as a noninvasive diagnostic tool for the characterization of emerging semiconductor technologies, especially oxide‐based TFTs. This approach provides essential insights to fabrication engineers, with potential to improve yield and reliability in flexible electronics manufacturing.