Skip to content

High-resolution electric field imaging based on intermittent-contact mode scanning NV center electrometry

FieldValue
JournalReview of Scientific Instruments
Published2026-04-01
AuthorsCheng Zhi, Zhiwei Yu, Mengqi Wang, Lingfeng Yang, Zihao Cui
DOI10.1063/5.0309968

Scanning nitrogen-vacancy center electrometry reached approximately 10 nm spatial resolution under ambient conditions on ferroelectric lithium niobate. This is a tenfold improvement over the approximately 100 nm reported for earlier scanning NV center electrometry. The gain came from an axially symmetric intermittent-contact probe with a 0.8 nm oscillation amplitude. That design allowed closer NV-to-sample engagement while retaining stable feedback.

Gradiometry addresses electrostatic screening from the diamond surface. Tip oscillation converts a nonuniform DC field in the laboratory frame into an AC field in the tip frame, which a dynamical decoupling protocol measures. Earlier probes operated in shear-force mode and oscillated above the approximately 100 kHz critical screening threshold. Structural asymmetry gave them a lateral component perpendicular to the primary oscillation axis, even without sample contact.

The authors identify this nonlinear motion as a source of measurement error and a limit on the minimum probe-sample distance. In intermittent contact, the primary axis is perpendicular to the sample, and axial symmetry retains linear harmonic motion. Their resolution simulation depends jointly on the NV-sample distance and oscillation amplitude. Resolution improves as the NV center approaches the sample, but the distance must exceed the amplitude. Reducing the amplitude therefore permits closer engagement and limits spatial averaging.

The probe uses a vertically oscillated quartz tuning fork at its second-order resonance near 180 kHz. The resonance period is approximately 5.5 µs. A glass beam carrying the diamond chip is attached to the lower prong. A counterweight on the upper prong is adjusted in mass and position to balance the second-order motion. The authors report that this symmetry also improves the quality factor.

Amplitude calibration used time-resolved photoluminescence. Confocal imaging first measured NV fluorescence along the oscillation axis. The fluorescence distribution had a broadening of approximately 2.5 µm. The objective was placed at the half-maximum position, where the fluorescence gradient was largest. During driven oscillation, the NV photoluminescence followed a sinusoid at the tuning fork frequency. The authors fitted maximum and minimum photon counts to obtain the probe amplitude.

Measured amplitude depended linearly on driving voltage. The experiments used 0.8 nm at 100 mV. This value is far below the tens-of-nanometer amplitudes associated with prior shear-force operation. It also leaves room for an NV-sample separation greater than the mechanical amplitude.

Spin-echo synchronization and field readout

Section titled “Spin-echo synchronization and field readout”

The spin-echo sequence was synchronized to the probe oscillation. A comparator converted the tuning fork sine wave into a digital square wave, which triggered a pulse blaster. The total echo time equaled one oscillation period. The π pulses were aligned with AC field zero crossings to maximize sensitivity.

An unknown electronic delay τe was found by adding a waiting delay τw after the trigger and sweeping it. Maximum accumulated phase occurred when τt = τe + τw equaled nπ/ω. Differential final-pulse sequences around the x and y axes projected phase into population probabilities. Nearby electrodes produced a static test field with constant AC amplitude during delay calibration.

A transverse bias field selected the electric field projection, and the Stark shift of NV spin transitions provided the readout. Measured populations followed the predicted phase dependence for all four final-pulse settings. Fits gave effective AC fields of 2.36(5) kV/cm and 2.61(35) kV/cm. These results validated the synchronized electrometry sequence before imaging lithium niobate.

Lithium niobate imaging and resolution test

Section titled “Lithium niobate imaging and resolution test”

The resolution test used PFM03 lithium niobate from NT-MDT Spectrum Instruments. The sample had a 10 µm stripe period with antiparallel ferroelectric domains. Spontaneous polarization was perpendicular to the surface. An 18 µm by 18 µm field-gradient map resolved periodic stripes. A line profile gave the same 10 µm periodicity reported by piezoresponse force microscopy.

An abrupt domain-wall field change should have produced a sharp transition. The measured walls were gradual. The authors attribute this likely behavior to surface screening or physisorption on the ferroelectric sample. Such effects can smooth an ideal step in the field.

Repeated scans then tested a localized stripe defect at the center of a domain. It showed similar contrast and shape, supporting a stable static feature rather than a transient artifact. Its possible origin in domain-switching dynamics was not established. Pulsed ODMR confirmed its electric-field nature and ruled out a magnetic artifact.

Line profiles came from scans with 10 µm, 2 µm, and 0.5 µm fields of view. The steepest edge gave approximately 10 nm resolution under the 10%-90% criterion. The simulated point spread function for an ideal δ(x) surface charge placed this edge width at an NV-sample distance of approximately 17 nm. The corresponding full width at half maximum was approximately 15 nm. The two resolution definitions should therefore be kept separate when comparing data.

Comparison with earlier scanning electrometry

Section titled “Comparison with earlier scanning electrometry”

Earlier scanning NV center electrometry demonstrated stray-field imaging from ferroelectric domains and microfabricated electrodes at approximately 100 nm resolution. The current setup raised measured resolution to approximately 10 nm. The main hardware change was intermittent-contact operation, which reduced amplitude from tens of nanometers to subnanometer scale and retained stable distance feedback.

The authors say this scale can resolve domains tens of nanometers in size, including structures discussed for van der Waals ferroelectrics. They propose using the method for real-space stray field mapping and quantitative local polarization. They also suggest studying predicted topological polar structures such as meronantimerons. These uses were proposed rather than demonstrated in the lithium niobate dataset.

The supplement cautions that modeled shear-force and intermittent-contact resolutions cannot be compared directly because the modes used different resolution definitions. The experimental comparison with prior work therefore rests on the reported approximately 100 nm versus approximately 10 nm performance.

Remaining limitations and device implications

Section titled “Remaining limitations and device implications”

The main unresolved issue is screening at the ferroelectric surface. Gradiometry overcomes screening from the diamond surface, but it does not restore an ideal field step hidden by sample screening. Device engineers should not interpret gradual domain-wall profiles as evidence that the measurement lacks 10 nm capability. They may instead reflect surface physics or adsorbed species.

The result also depends on stable intermittent-contact operation. The probe must limit off-axis motion, maintain distance feedback, and keep the NV-sample distance near the modeled 17 nm when seeking 10 nm edge width. The measurement uses shallow NV centers, so diamond sensing quality and NV layer location affect probe design.

The paper does not specify chip dimensions, surface roughness, NV implantation schedule, or diamond growth method. It also does not provide an error bar for the 10 nm resolution estimate. A material choice based only on composition would therefore omit important device requirements.

The paper’s electrometry probe uses a diamond chip with shallow NV centers for intermittent-contact field sensing. 6CCVD’s diamond materials catalog includes single-crystal diamond grown by MPCVD, and the engineering support page can be used to define the chip geometry and NV treatment before custom fabrication.

View Original Abstract

Scanning nitrogen-vacancy (NV) center electrometry has shown potential for quantitative quantum imaging of electric fields at the nanoscale. However, achieving nanoscale spatial resolution remains a challenge since employing gradiometry to overcome electrostatic screening causes resolution-limiting trade-offs including the averaging effect and the sensor-sample proximity. Here, we demonstrate a scanning NV center protocol that achieves an enhanced spatial resolution of ∼10 nm. We develop an axially symmetric probe with a sub-nanometer oscillating amplitude, which simultaneously provides robust intermittent-contact mode feedback and ensures close engagement between the diamond tip and the sample. As an example, we experimentally demonstrate a 10 nm spatial resolution on ferroelectric lithium niobate. Scanning NV center electrometry with this resolution can directly resolve the nanoscale polar textures and dynamics of emerging ferroelectrics, which commonly arise on the scale of tens of nanometers.