Skip to content

IMPROVING THE EFFICIENCY OF USING DIAMOND GRINDING WHEELS ON THE ORGANIC BINDER BY CALCULATING THE RATIONAL STRUCTURE AND INTRODUCTION OF ULTRADISPERSED DIAMOND

FieldValue
JournalCutting & Tools in Technological System
Published2026-05-15
AuthorsYevgeniy Ostroverkh
DOI10.20998/2078-7405.2026.104.05

Detonation nanodiamond at about 1% by weight of the SFP-012A polymer binder raised Vickers microhardness by 23%, from 78 HV for the unmodified bond to 96 HV. The modified rings were 125 × 3 × 3 mm and were tested at a 50 g load with a 136° diamond pyramid. The paper supports nanodiamond as a bond modifier, but it does not report grinding tests of wheels made with the modified binder.

The measured maximum occurred at 1 wt%. The 0.5% sample reached 91 HV, which the authors report as a 16% increase over the 78 HV control. The 1% sample reached 96 HV and gave the reported maximum increase of 23%. A sample reported as 1.5% reached 93 HV, so the measured hardness fell as loading increased beyond 1%.

Binder specimenNanodiamond mass fractionVickers microhardnessReported change
B2-01 controlNo nanodiamond78 HVReference
Modified binder0.5%91 HV16%
Modified binder1%96 HV23%
Modified binder1.5%93 HVNot stated

The authors therefore recommend a nanodiamond mass fraction of about 1% of the binder weight. Their results support this value as the best formulation among the reported hardness measurements, rather than as a universal optimum for all polymer bonds.

Why the organic bond controls grain retention

Section titled “Why the organic bond controls grain retention”

More than half of the diamond loss in grinding wheels occurs when grains fall out of the binder, according to the paper’s literature review. Organic binders occupy more than 55% of the produced binder range because they are easy to manufacture and low cost. The review also reports that current binders permit use of the abrasive’s potential by no more than 20%. This motivates selection rules that combine binder strength, grain grade, and grain concentration.

The paper treats the bond as more than a carrier for abrasive grains. Diamond retention depends on the adhesion activity of the binder components and their adhesion work on the diamond surface. Graphite in the B2-01 bond already improves antifriction properties at 0.8% of the diamond layer’s volume. The proposed nanodiamond route is intended to change bond hardness and elasticity without changing the established filler-to-diamond ratio.

The authors suggest that changed friction in the diamond layer could reduce the microcutting-zone temperature. They did not measure this temperature change during the nanodiamond binder experiment.

Three-dimensional dynamic simulation in LS-DYNA was used to study the binder, grain, and workpiece system. The workflow included geometry creation, finite element meshing, mesh parameterization, material laws, contact properties, load assignment, and result analysis.

The organic binder used a solid body model defined by elastic modulus, shear modulus, Poisson’s ratio, and material density. The metal catalyst, metal coating, and workpiece used an elastic-plastic model with von Mises plasticity. This model allowed the authors to follow changes in equivalent stress, temperature, and strain.

Figure 1 follows stress in the diamond-binder system for 63/50 grit as the grinding-area temperature changes. Figure 2 maps stress through the binder-grain-metal phase system at 150% grain concentration. The text does not provide numerical stress limits for either figure. The method’s practical value is its ability to examine alloy content, grain brand, and grain concentration during wheel design.

The paper also treats grinding simulation as a way to select process parameters for workpiece quality, cutting time, and economic results. Its calculation indicates that diamond concentration in the abrasive layer can be lower than conventional serial-production values. However, the paper gives no numerical reduction factor for that conclusion.

A separate coating result reports a 27% increase in wheel performance for nickel coatings containing nanodiamond compared with conventional nickel. The modified deposition adds a nanodiamond suspension during deposition of the second nickel layer and each subsequent layer. This result concerns the metal coating around synthetic diamond grains, not the nanodiamond-modified SFP-012A binder rings.

The conclusion gives another 27% result with a different metric. Replacing a compound alloy dominated by Mn with one dominated by Ni reduced the calculated probability of grain failure under force and thermal load by 27%. The coating test and calculation address the metal-binder interface. The 96 HV result comes from a separate polymer-bond experiment and should not be treated as evidence of the same performance gain.

Pulverbakelite was mixed with an aqueous nanodiamond suspension to avoid agglomeration and distribute the particles through SFP-012A. The resulting emulsion was dried completely and then mixed with ultrasonic vibration. The composite was sintered using the standard process for manufacturing polymer-bond diamond wheels.

The control was B2-01, based on SFP-012A with 6% by weight urotropine, also called hexamethylenetetramine. A similar modified composition contained SFP-012A, filler, 6 wt% GMTA, and nanodiamond additions of 0.5%, 1%, and 2% by weight. The authors sintered rings measuring 125 × 3 × 3 mm.

Hardness was measured on a PMT-3 device at a 50 g load. The indenter was a diamond pyramid with a 136° apex angle. The control reached 78 HV. The reported 0.5%, 1%, and 1.5% formulations reached 91 HV, 96 HV, and 93 HV, respectively. These values measure composite microhardness rather than wheel life or grinding performance.

Earlier studies cited in the paper show that nanodiamond can modify several polymer systems. Filling phenylon C-2 increased abrasive wear resistance by 3.5 times, elastic modulus by 104.5 MPa, and compression yield strength by 6.5 MPa. Other cited systems showed large changes in tensile behavior.

Polymer systemModulus without nanodiamond, MPaModulus with nanodiamond, MPaTensile strength without nanodiamond, MPaTensile strength with nanodiamond, MPa
Fluoroelastomer8.59215.7173
Polysilicon195352154
Isoprene rubber7.712.320.528.2

These results support nanodiamond as a general polymer modifier. They do not establish the wear resistance or grinding life of SFP-012A because the cited work used different polymers, loadings, and test endpoints. The 23% hardness increase also cannot be compared directly with the reported 20% limit on abrasive potential. The measurements address different properties.

Limits and grinding wheel design implications

Section titled “Limits and grinding wheel design implications”

The hardness result has several boundaries. The paper gives no replicate count, error bars, nanodiamond particle size distribution, or direct image of particle dispersion. It lists 2% nanodiamond in the formulation but reports the hardness of a 1.5% sample without giving a result for 2%. The proposed effect on grinding-zone temperature and constant thermal conductivity remains theoretical for the polymer composition.

The metal coating recommendations are more specific. The paper describes conventional coating thickness as 56 to 100 wt.%. It recommends 175 to 200% for 50/40 to 80/63 grit and 150 to 175% for 100/80 to 160/125 grit. For 200/160 to 400/315 grit, it gives a coating value of 125 wt.%. These are coating design values, not nanodiamond concentrations.

For wheel designers, 1 wt% is the strongest supported laboratory starting point for SFP-012A because it produced 96 HV. Production adoption still requires wheel-life, grinding-force, temperature, and workpiece-quality tests at the intended grit and concentration. The measured result supports binder modification through microhardness. It does not establish a measured increase in grinding productivity for the polymer-bond wheel.

View Original Abstract

The article presents one of the options for developing scientifically based recommendations for choosing a rational combination of the strength of the binder, the size of the diamond grain, the concentration of diamond grains with the physical and mechanical properties of different types of binders in the manufacture of diamond grinding wheels. The conducted studies have shown the feasibility of using detonation nanodiamond powders as a modifier of the polymer binder. The introduction of nanopowder into the polymer leads to an increase in microhardness by 23%, and the recommended mass fraction of nanodiamond should be about 1% of the weight of the binder. It is possible to use such polymer compositions in the diamond layer of standard grades, which theoretically will increase their hardness due to constant thermal conductivity.