Skip to content

Seawater Oxidation on Boron-Doped Diamond Electrodes

FieldValue
JournalJournal of The Electrochemical Society
Published2026-07-02
AuthorsOlga Baturina, Graham T. Cheek, Rachel Nixon, Dagmar H. Leary, Christopher Katilie
DOI10.1149/1945-7111/ae8581

Commercial freestanding polycrystalline boron-doped diamond generated hypochlorite as the dominant chlorine oxidation product in synthetic ASTM seawater at pH 8.2. Its average Faradaic efficiency was about 85%. After 10 minutes, hypochlorite exceeded chlorate by two orders of magnitude and perchlorate by five orders.

Electrooxidation tests used current densities from 1 to 100 mA cm⁻² for 10 minutes in synthetic seawater and 0.5 M NaCl at pH 8.2. Hypochlorite concentration increased linearly with current density in both electrolytes. At 100 mA cm⁻², the hypochlorite concentration was about 30% higher in NaCl. Chlorate concentration was also about 30% higher in NaCl. Its increase was noticeable only at or above 25 mA cm⁻². Perchlorite concentration plateaued from 1 to 50 mA cm⁻² and rose slightly above 50 mA cm⁻². Chlorite was not detected. Seawater produced more perchlorate above 50 mA cm⁻², but its concentration was close to the 10⁻⁸ M LC-MS detection limit. The authors therefore could not establish preferential perchlorate formation in seawater.

The commercial Element Six electrodes were square, 15 mm by 15 mm, and exposed 0.503 cm² in the cell. SEM showed ridges and 10 to 20 µm grains. Raman peaks at 1332 and 1210 cm⁻¹ confirmed diamond and substitutional boron. A 1530 cm⁻¹ peak indicated graphitic sp² carbon at grain boundaries. SIMS measured 2.1 × 10²⁰ atoms B cm⁻³ near the surface and 1.9 × 10²⁰ atoms B cm⁻³ at 4 µm. No nitrogen, oxygen, or silicon dopants were detected. The lower Raman estimate of substitutional boron was 1.6 × 10²⁰ atoms B cm⁻³, consistent with interstitial boron. XPS of acid-treated material gave an sp³-to-sp² peak area ratio of 51.97.

Before testing, the electrodes were treated for 10 minutes with hot concentrated acids. The acid mixture was 3 mL HCl, 2 mL HNO₃, and 2 mL H₂SO₄. After rinsing, ultrasonication for 5 minutes, and drying, they were activated at −3 V vs RHE for 30 minutes in 0.5 M H₂SO₄. Cyclic voltammetry then showed about 10 mA cathodic current at −0.6 V vs RHE.

Synthetic seawater was prepared from 41.95 g of ASTM powder per liter of 18.2 MΩ cm water. The mixture was stirred for 48 hours, filtered, and adjusted to pH 8.2 with HCl. Milli-Q water had 18 MΩ cm resistivity and less than 5 ppb total organic carbon.

The flat cell was open to air and used a Viton O-ring, platinum foil counter electrode, and Ag/AgCl reference electrode with 3 M KCl. Most runs used an undivided configuration. A cell separated by a Nafion 112 membrane was used for more accurate assessment of the working electrode. Each current density was tested for 10 minutes in fresh electrolyte.

Hypochlorite was measured by N,N-diethyl-p-phenylenediamine colorimetry and reported as mg Cl₂/L. Readings were converted assuming one mole of Cl₂ equaled one mole of ClO⁻. LC-MS with multiple reaction monitoring quantified chlorite, chlorate, and perchlorate. NMR detected perchlorate near 10⁻⁴ M during the 24 and 48 hour tests.

Linear sweep voltammetry gave the same 2.4 V vs RHE onset in both electrolytes, while Tafel analysis placed onset at 1.83 V vs RHE. Below 4 mA cm⁻², both solutions had a 120 mV Tafel slope. This supports similar chloride oxidation mechanisms and slow electron transfer. A slope change above 4 mA cm⁻² indicated a mechanism change. Steady-state polarization agreed with 1 mV s⁻¹ voltammetry below about 11 mA cm⁻². At higher currents, voltammetry gave higher currents than steady state, likely because of surface oxidation.

Faradaic efficiency was calculated using a two-electron hypochlorite formation assumption. In 0.5 M NaCl, efficiency exceeded 100% above 5 mA cm⁻². The authors interpret this as evidence for oxidation involving fewer than two electrons. They suggest a near-surface reaction between one-electron products and chloride contributes to hypochlorite formation. Seawater Faradaic efficiency averaged 85%.

Adding sodium bicarbonate and boric acid to 0.5 M NaCl at pH 8.2 did not change efficiency. This result did not support the proposed radical-scavenging explanation. Divided and undivided cells gave similar efficiencies, so counter-electrode reduction was not significant. The authors instead attribute the lower seawater efficiency to reactions of ClO⁻ with trace elements and organic impurities omitted from Table S1.

Earlier highly doped BDD electrodes produced chlorine with 60% to 65% Faradaic efficiency in diluted NaCl and 0.6 M NaCl at pH 2 and 7. Oxygen efficiency was about 3% at pH 2 and 10% at pH 7. At pH 12, chloride oxidation was inhibited and oxygen efficiency reached 40% to 50%. The present work addressed the untested interval at seawater pH 8.2 and 0.5 M chloride.

Santos and coworkers reported similar concentrations of ClO⁻, ClO₃⁻, and ClO₄⁻ in 0.06 M NaCl. The paper found a two-order excess over chlorate and a five-order excess over perchlorate, unlike that earlier pattern. Vacca and coworkers found that raising chloride from 0.14 to 0.57 M suppressed ClO₃⁻ and BrO₃⁻ at 2.5 to 5 mA cm⁻². They detected no perchlorate.

The commercial freestanding electrode had a 2.2 V stability window in 0.1 M HClO₄. A BDD film on silicon had a reported 3.1 V window, showing the effect of manufacturing route.

A 48 hour test at 100 mA cm⁻² measured electrode and electrolyte behavior. In 0.5 M NaCl, potential rose from 4.4 to 4.9 V vs RHE. The average increase was about 10 mV h⁻¹. In seawater, potential reached 5.1 V after 24 hours and 5.7 V after 48 hours. Its average increase was 27 mV h⁻¹, which was 2.7 times the NaCl rate.

Perchlorate increased monotonically to 0.7 mM in NaCl and 0.82 mM in seawater. The final values differed by only 15%. Under a linear-growth assumption, the 10 minute LC-MS result gave 3 × 10⁻⁶ mM min⁻¹. The 48 hour NMR result gave 2.85 × 10⁻⁴ mM min⁻¹. The authors used this two-order difference to infer that perchlorate accumulation was not linear.

After 10 minutes, the C-O-C/C-OH peak area to combined C=O and O-C=O area rose from 0.97 for acid-treated material to 1.24 in NaCl and 1.69 in seawater. After 48 hours, the sp³-to-C* ratio fell from 1.98 for acid-treated material to 1.55 in NaCl and 1.40 in seawater. XPS indicated that most oxygen groups were C-OH. The authors could not identify C* conclusively.

XPS also found 1.4 at% iron after 48 hours of seawater oxidation and a metal-oxygen bond. They suggest contamination, iron oxide formation, and surface oxidation contributed to higher overpotentials.

The measured selectivity supports boron-doped diamond anodes for seawater electrochlorination near pH 8.2. The authors identify reverse osmosis feed disinfection and naval ballast seawater treatment as target uses. This study did not measure microbial inactivation, so it establishes product selectivity and electrode behavior rather than treatment performance.

Electrolyte composition affects both efficiency and performance decay. The seawater matrix had lower hypochlorite efficiency and faster potential drift than the NaCl reference. The authors linked trace constituents in seawater to parasitic hypochlorite loss. The 48 hour test does not establish an industrial service life. Potential fluctuations above 50 mA cm⁻² were attributed to extensive bubble generation.

Perchlorate was near the LC-MS limit after 10 minutes, while the 48 hour test produced 0.82 mM. A short byproduct assay can therefore miss longer-term accumulation. The efficiency above 100% in NaCl also shows that the two-electron model does not capture the full reaction network.

The tested seawater electrolysis anode uses freestanding polycrystalline boron-doped diamond. 6CCVD offers boron-doped diamond grown by MPCVD in its diamond materials catalog, which matches the paper’s conductive electrode material family. Its engineering support service can be used to assess electrode preparation and cell requirements for this application.

View Original Abstract

Herein, we explore selectivity toward generation of ClO x ( x = 1-4) anions and durability of commercial polycrystalline free-standing boron-doped diamond (BDD) electrodes in synthetic ASTM seawater oxidation. 10 min electrooxidation experiments at current densities from 1 to 100 mA cm −2 revealed formation of ClO − , <mml:math xmlns:mml=“http://www.w3.org/1998/Math/MathML” overflow=“scroll”> <mml:mrow> <mml:msubsup> <mml:mrow> <mml:mtext>ClO</mml:mtext> </mml:mrow> <mml:mn>3</mml:mn> <mml:mo>−</mml:mo> </mml:msubsup> </mml:mrow> </mml:math> , and <mml:math xmlns:mml=“http://www.w3.org/1998/Math/MathML” overflow=“scroll”> <mml:mrow> <mml:msubsup> <mml:mrow> <mml:mtext>ClO</mml:mtext> </mml:mrow> <mml:mn>4</mml:mn> <mml:mo>−</mml:mo> </mml:msubsup> </mml:mrow> </mml:math> anions. ClO − anions were found to be the dominant reaction product, with concentrations exceeding those of <mml:math xmlns:mml=“http://www.w3.org/1998/Math/MathML” overflow=“scroll”> <mml:mrow> <mml:msubsup> <mml:mrow> <mml:mtext>ClO</mml:mtext> </mml:mrow> <mml:mn>3</mml:mn> <mml:mo>−</mml:mo> </mml:msubsup> </mml:mrow> </mml:math> and <mml:math xmlns:mml=“http://www.w3.org/1998/Math/MathML” overflow=“scroll”> <mml:mrow> <mml:msubsup> <mml:mrow> <mml:mtext>ClO</mml:mtext> </mml:mrow> <mml:mn>4</mml:mn> <mml:mo>−</mml:mo> </mml:msubsup> </mml:mrow> </mml:math> by two and five orders of magnitude, respectively. The same trend was observed in 0.5 M NaCl at pH 8.2 that was used as a reference, although the <mml:math xmlns:mml=“http://www.w3.org/1998/Math/MathML” overflow=“scroll”> <mml:mrow> <mml:msubsup> <mml:mrow> <mml:mtext>ClO</mml:mtext> </mml:mrow> <mml:mn>3</mml:mn> <mml:mo>−</mml:mo> </mml:msubsup> </mml:mrow> </mml:math> concentration was found to be ca 30% higher. ClO − ions were generated in seawater with ca 85% Faradaic efficiency (FE), which was lower than that in 0.5 M NaCl. This difference was attributed to parasitic reactions of ClO − with trace elements and organic impurities present in seawater. We demonstrated that radical scavengers such as H 3 BO 3 and <mml:math xmlns:mml=“http://www.w3.org/1998/Math/MathML” overflow=“scroll”> <mml:mrow> <mml:msubsup> <mml:mrow> <mml:mtext>HCO</mml:mtext> </mml:mrow> <mml:mn>3</mml:mn> <mml:mo>−</mml:mo> </mml:msubsup> </mml:mrow> </mml:math> present in seawater do not affect FEs of the ClO − production. The 48 h durability tests demonstrated a slight performance decay, more pronounced in seawater. Performance decay was accompanied by the BDD surface oxidation with formation of carbonyl, carboxyl and hydroxyl groups, dominated by OH groups.