1 3 C Nanocrystalline Diamond Capsules - Fabrication, Characterization, and Opportunities for High‐Energy‐Density Experiments
Paper details
Section titled “Paper details”| Field | Value |
|---|---|
| Journal | Advanced Functional Materials |
| Published | 2026-08-24 |
| Authors | Maxwell A. T. Marple, Sean Michael Hayes, Rajeev Kumar, T. Fehrenbach, Derrick C. Kaseman |
| DOI | 10.1002/adfm.77795 |
| Citations | 1 |
MPCVD produced isotopically enriched ¹³C nanocrystalline diamond coatings with a measured density of 3.64 g cm⁻³. The value was 8% above comparable ¹²C nanocrystalline diamond coatings made with the same process. SIMS found a ¹³C/¹²C ratio above 100 across the measured cross-section, and NMR gave approximately 93% diamond phase purity.
A denser ¹³C ablator
Section titled “A denser ¹³C ablator”Natural diamond has a density of 3.3 to 3.5 g cm⁻³, compared with about 1 g cm⁻³ for glow discharge polymer ablators. Higher density permits a thinner capsule for a given ablator mass and shortens shock transit time. The ¹³C design adds density because the heavier isotope raises the expected density of isotopically pure ¹³C nanocrystalline diamond.
A simple ablative rocket model compared designs with equal final mass and implosion velocity. It predicted that ¹³C required 2.4% more initial mass, but its higher density produced a roughly 5% thinner shell. The model also gave a roughly 8% higher mass ablation rate and a shorter laser pulse. The higher mass-to-charge ratio slightly reduced theoretical rocket efficiency. These are model results, not measured implosion gains. The shorter timing could improve symmetry control, but the authors did not quantify potential gains.
MPCVD growth and density metrology
Section titled “MPCVD growth and density metrology”Uniform 10 to 40 µm coatings were grown on 2.1 mm diameter spherical Si mandrels. Typical conditions were 4% ¹³CH₄ in H₂, 50 to 100 mbar, 4 to 6 kW, and 700 °C. The growth rate was about 0.35 µm/h. Purge-pump cycles and a 20 sccm ¹³CH₄ flow reduced residual ¹²C contamination.
The density batch used 26 coated spheres with 36 µm coatings and four uncoated references. Polishing reduced as-grown Sa from about 85 nm to below 5 nm. A 0.1 µg balance measured mass difference, while a custom micrometer had 0.6 µm accuracy and 0.08 µm repeatability. The calculated density error was ±0.006 g cm⁻³, or 0.16%, and measured standard deviation was ±0.024 g cm⁻³, or 0.65%.
The 3.64 g cm⁻³ result agreed with the 3.63 g cm⁻³ expectation from 13/12 times 3.35 g cm⁻³. It exceeded the 3.35 g cm⁻³ density of ¹²C nanocrystalline diamond made with the same process.
Isotopic purity and phase verification
Section titled “Isotopic purity and phase verification”SIMS used a 20 nA Cs⁺ beam at 20 keV to sputter a 50 by 50 µm² surface. Data from the central 33 µm region showed a ¹³C/¹²C ratio above 100 throughout the cross-section. This corresponds to more than 99% ¹³C in the paper’s interpretation.
Raman spectroscopy with 455 nm excitation shifted the diamond peak from 1332 cm⁻¹ for ¹²C to 1278 cm⁻¹ for ¹³C. A static ¹³C NMR doublet with a 10.8 kHz full width at half maximum also supported near-total enrichment.
The Raman diamond peak contributed only 1% of total intensity because visible excitation overweights sp² carbon. The low Raman contribution therefore did not represent the NMR phase fraction. The stronger fluorescence background of the nanocrystalline coatings suggested a higher defect density than the microcrystalline references.
Grain structure and nanovoids
Section titled “Grain structure and nanovoids”HAADF-STEM at 200 kV found elongated ordered regions several micrometers long, aligned with the growth direction. High-resolution images and FFT analysis showed sub-100 nm grains with frequent twin or small-angle boundaries. Under-focus TEM and selected-area diffraction confirmed a broad grain distribution, with 10 to 20 nm grains dominant. Carbon K-edge EELS showed predominantly sp³ bonding and minimal sp² contribution.
Thickness maps found about 0.3 mean-free-path variations, with a 100 nm mean free path at 200 keV. These regions were interpreted as nanovoids formed when nonaligned grains collide during growth. Most measured nanovoids were 15 to 20 nm across, and only a small fraction reached 30 to 40 nm.
They occupied 2 to 3.5% of the TEM image area and 0.3 to 0.5% of volume for a 100 nm lamella. Nanovoids contributed to the roughly 5% density deficit relative to single-crystal diamond but did not explain it fully.
NMR quantifies grain-boundary chemistry
Section titled “NMR quantifies grain-boundary chemistry”NMR measurements were conducted at 298 K with 12.5 kHz magic-angle spinning. Direct-polarization ¹³C spectra were quantitative for nanocrystalline diamond because its short relaxation time allowed full signal recovery. The paper reports approximately 93% diamond phase purity.
Deconvolution assigned 74.82 ± 1.49% and 17.82 ± 1.55% to two bulk sp³-C components. Their widths were 3.17 and 6.34 ppm. The authors hypothesized that these components represent unstrained and strained lattice regions. The 28.9 ppm shoulder accounted for 3.50% and was assigned to stacking faults and twin boundaries.
Protonated sp³ carbon accounted for 2.9%, divided between peaks at 35.0 and 43.8 ppm. The broader 43.8 ppm signal was consistent with high-angle boundaries. The narrow signal was consistent with low-angle boundaries or faceted hydrogen-terminated nanovoid surfaces.
The 65 ppm ta-C assignment remained tentative at 0.4%. Graphitic sp²-C at 140.7 ppm was assigned 0.5%. Previous SIMS of ¹²C coatings found oxygen below about 10 ppm, which ruled out oxygen-bonded carbon as the explanation for the 65 ppm peak. HETCOR placed proton shifts between 0 and 2.6 ppm, typical of methine environments.
Defects and density reconciliation
Section titled “Defects and density reconciliation”Continuous-wave EPR at 9.86 GHz produced a broad singlet with g = 2.00589, attributed mainly to dangling carbon bonds. Spin counting gave 8.5 × 10¹⁸ spins/g in ¹³C nanocrystalline diamond and 1.5 × 10¹⁷ spins/g in ¹³C microcrystalline diamond. Although SIMS found about 60 ppm nitrogen, no nitrogen triplet appeared even at 1 µW microwave power. The authors concluded that nitrogen-related centers were below the EPR detection limit.
Saturation recovery gave a 3.6 s ¹³C T₁ under magic-angle spinning and 2.0 s under static conditions. The microcrystalline value was about 1900 s, but incomplete recovery made it a lower bound. Those results support direct and spin-diffusion relaxation in the more defective nanocrystalline sample. The authors estimated that paramagnetic sites made 0.34% of sample volume unobservable by NMR, so the speciation remained representative.
The NMR density model assigned 92.2 vol.% to diamond lattice sites, 6.5% to sp³-CH, 0.5% to ta-C, and 0.8% to sp²-C. These fractions produced 3.37 g cm⁻³ for ¹²C nanocrystalline diamond. Correcting for the 0.4% nanovoid fraction reduced the prediction to 3.36 g cm⁻³, close to the measured 3.35 g cm⁻³. The grain-boundary volume was below 10%, which sets a 0.35 nm upper bound on average thickness for 10 nm grains.
Implications for target engineering
Section titled “Implications for target engineering”The paper identifies three target-engineering opportunities. First, density gradients across nanocrystalline and W-doped nanocrystalline diamond interfaces may support implosion stability. Second, the modeled 5% thinner ¹³C shell provides the same ablator mass with shorter shock transit and may aid symmetry control. Third, an integrated ¹³C layer can support ¹³N production through ¹³C(p,n)¹³N.
The paper’s diagnostic example uses 14.7 MeV protons produced by ³He plus D fusion reactions. Detection could use the NIF Radiochemical Analysis of Gaseous Samples system to study yield and fuel-ablator mix. The first shells for this test are described as being fabricated, so the paper does not demonstrate diagnostic performance.
The ablative rocket model was illustrative, and quantitative gains remain outside the study. Simulation-driven design and experimental validation are still required. Higher density does not guarantee stability because it can increase or decrease resistance to shell perturbations.
For material selection, isotope purity and phase content are only part of the specification. Density, grain-boundary chemistry, defect concentration, and surface roughness also affect shock timing, stability, and diagnostics. The NMR framework is being applied to W concentration and molecular-dynamics models for shock propagation.
Materials and support
Section titled “Materials and support”The paper requires an MPCVD-grown ¹³C-enriched polycrystalline diamond ablator coating, 10 to 40 µm thick on 2.1 mm spherical Si mandrels, with polished Sa below 5 nm. The 6CCVD diamond materials catalog lists single-crystal and polycrystalline diamond grown by MPCVD, with thickness from 0.1 to 500 µm, which matches the listed coating family and thickness range. It does not list ¹³C isotopic enrichment or spherical capsule geometry, so those requirements should be confirmed through engineering support before specifying capsule material.
View Original Abstract
ABSTRACT Nanocrystalline diamond (NCD) targets have recently enabled inertial confinement fusion (ICF) ignition at the National Ignition Facility (NIF), with gains exceeding the input laser energy. Achieving ignition requires NCD targets with carefully tuned density profiles and high material uniformity to minimize fuel‐ablator mix. Here, we report on the fabrication of high‐isotopic‐purity 13 C‐NCD capsules with a 13 C/ 12 C ratio greater than 100 and a density of 3.64 g cm −3 , 8% higher than comparable 12 C‐NCD coatings. The higher density shortens shock transit times, offering symmetry control advantages and enabling density gradient tuning across NCD/W‐NCD interfaces for improved implosion stability. 13 C‐NCD also opens a new diagnostic platform for studying fuel‐ablator mix and yield in NIF ICF experiments through 13 N production via the 13 C(p,n) 13 N reaction. Leveraging high isotopic purity of 13 C‐NCD coatings, we perform quantitative characterization of non‐diamond carbon phases using solid‐state direct‐polarization nuclear magnetic resonance (NMR) spectroscopy. This reveals the presence of hydrogenated carbon (2.9 at.%), graphitic carbon (0.5 at.%), and tetrahedral amorphous carbon (0.4 at.%), yielding previously unavailable insight into NCD ablator composition and structure. This work clarifies the nature of NCD ablator shells and lays the foundation for new target designs that exploit 13 C‐NCD’s higher density and enable diagnostics for ICF experiments.
Boron Doped Single Crystal Diamond Plate
View Specs →
Electronic Grade Intrinsic Diamond Epitaxial Wafer H Terminated Superior 100 Mosfet Ready Substrate
View Specs →
High Concentration Quantum Grade Single Crystal Diamond
View Specs →References we cover
Section titled “References we cover”- Magnetic Resonance Study of Bulky CVD Diamond Disc
- Structural, Raman and photoluminescence studies on nanocrystalline diamond films - Effects of ammonia in feedstock