Optimization of Polycrystalline CVD Diamond Seeding with the Use of sp3/sp2Raman Band Ratio
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2015-07-01 |
| Journal | Acta Physica Polonica A |
| Authors | Łukasz Gołuński, Michał Sobaszek, Mateusz Gardas, Marcin Gnyba, Robert Bogdanowicz |
| Institutions | Gdańsk University of Technology |
| Citations | 3 |
| Analysis | Full AI Review Included |
Executive Summary
Section titled “Executive Summary”- The study optimizes nanodiamond seeding of silicon substrates before microwave plasma-enhanced chemical vapor deposition (MPCVD) of polycrystalline diamond.
- Three seeding colloids were compared: deionized water, isopropanol, and DMSO, with dispersed grain sizes of 150-200 nm, 400-500 nm, and 30-35 nm, respectively.
- DMSO produced the highest diamond ideality factor in all tested conditions, consistent with its small dispersed particle size and high polarity index.
- Diamond growth was performed using a 1% CH4/H2 mixture at 50 Torr, 300 sccm total flow, 2.45 GHz microwave excitation, 1300 W source power, and a substrate temperature of 700°C.
- Growth durations of 30 and 120 minutes were evaluated with and without bias-enhanced nucleation (BEN).
- BEN applied at −250 V increased the resulting crystal size and sp3/sp2 Raman ratio, improving diamond phase quality.
- Raman spectroscopy identified the diamond sp3 peak at 1332 cm−1, the D band at 1355 cm−1, the C-H bending band at 1440-1480 cm−1, and the G band at approximately 1560 cm−1.
- The introduced diamond ideality factor, di, provides a rapid Raman-based estimate of film quality and relative sp3 content.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Substrate material | p-Si(100) | — | Silicon substrate used for seeding and diamond growth |
| Substrate resistivity | 0.001-0.005 | Ω·cm | Electrical resistivity of the p-type silicon wafers |
| Substrate pretreatment | 5 min in acetone followed by 5 min in isopropanol | min | Cleaning sequence before seeding |
| Seeding duration | 1 | h | Nanodiamond colloid treatment of silicon |
| Seeding rinse | Isopropanol | — | Rinse medium after the seeding process |
| Drying medium | Nitrogen | — | Drying under a nitrogen stream |
| DND powder grade | ND-50 | — | Detonation nanodiamond powder |
| Initial DND cluster size | Up to 50 | nm | Powder specification before dispersion |
| DMSO colloid grain size | 30-35 | nm | Dispersed grain size after multistage preparation |
| Water colloid grain size | 150-200 | nm | Dispersed grain size after high-power sonication |
| Isopropanol colloid grain size | 400-500 | nm | Dispersed grain size after high-power sonication |
| DMSO polarity index | 1 | — | Highest polarity among the tested media |
| Water polarity index | 0.88 | — | Intermediate polarity |
| Isopropanol polarity index | 0.55 | — | Lowest polarity |
| Initial chamber pressure | 10−4 | Torr | Vacuum level before process-gas introduction |
| Growth pressure | 50 | Torr | MPCVD operating pressure |
| CH4 concentration in H2 | 1 | % | Methane fraction in the process gas |
| Total gas flow | 300 | sccm | Hydrogen-methane mixture flow rate |
| Microwave frequency | 2.45 | GHz | Plasma excitation frequency |
| Microwave source power | 1300 | W | Source power used for diamond growth |
| Substrate temperature | 700 | °C | Sample-holder temperature during growth |
| BEN voltage | −250 | V | Negative bias applied to the sample holder |
| Growth duration | 30 or 120 | min | Tested deposition times |
| SEM accelerating voltage | 20 | kV | Voltage used for morphology imaging |
| Raman excitation wavelength | 532 | nm | Diode-pumped solid-state laser |
| Raman integration time | 20 | s | Integration time for each spectrum |
| Raman spectral range | 200-3500 | cm−1 | Spectral acquisition range |
| Diamond sp3 Raman peak | 1332 | cm−1 | Crystalline diamond phase |
| D band | 1355 | cm−1 | Disorder-related carbon band |
| C-H bending band | 1440-1480 | cm−1 | Hydrogenated carbon region |
| G band | Approximately 1560 | cm−1 | sp2-bonded carbon band |
| Best-performing seeding medium | DMSO | — | Highest di values in all tested cases |
| BEN effect | Increased crystal size and sp3/sp2 ratio | — | Bias-enhanced nucleation improved film quality |
Key Methodologies
Section titled “Key Methodologies”-
Prepare nanodiamond colloids
- Disperse detonation nanodiamond powder in deionized water, isopropanol, or DMSO.
- Use high-power sonication for the water- and isopropanol-based systems.
- Prepare DMSO colloid through a multistage chemical treatment involving dimethylformamide, allyl bromide, sodium carbonate, vacuum filtration, centrifugation, evaporation, and repeated DMSO addition.
-
Control colloid dispersion
- Target grain sizes of:
- 30-35 nm for DMSO.
- 150-200 nm for deionized water.
- 400-500 nm for isopropanol.
- Use freshly prepared aqueous and isopropanol colloids to limit precipitation.
- Target grain sizes of:
-
Clean silicon substrates
- Use p-Si(100) wafers with resistivity of 0.001-0.005 Ω·cm.
- Immerse sequentially in acetone and isopropanol for 5 minutes each.
- Dry the substrates under nitrogen.
-
Seed the substrates
- Expose the silicon wafers to the selected colloid for 1 hour.
- Rinse with isopropanol.
- Dry under nitrogen.
-
Load and evacuate the MPCVD chamber
- Place the seeded wafers in a Seki AX5400 CVD system.
- Reduce chamber pressure to 10−4 Torr.
-
Establish the growth atmosphere
- Introduce hydrogen and methane at a CH4:H2 ratio of 1%.
- Maintain total flow at 300 sccm.
- Set chamber pressure to 50 Torr.
-
Generate the plasma
- Use 2.45 GHz microwave radiation.
- Operate the microwave source at 1300 W.
- Maintain the sample holder at 700°C.
-
Apply optional BEN
- Apply a negative substrate bias of −250 V during growth.
- Prepare matched samples with BEN disabled to isolate the bias effect.
-
Grow microcrystalline diamond
- Use growth times of 30 and 120 minutes.
- Evaluate all combinations of colloid, growth time, and BEN condition.
-
Characterize the films
- Use SEM in secondary-electron mode at 20 kV to assess morphology and crystal coverage.
- Record Raman spectra from 200-3500 cm−1 using a 532 nm laser and 20 s integration time.
- Analyze the sp3, D, C-H, and G bands.
- Calculate the relative sp3/sp2 ratio and diamond ideality factor.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”Applicable Materials
Section titled “Applicable Materials”- Optical Grade SCD: Appropriate for applications requiring high crystalline quality, low disorder, and controlled optical or electronic behavior.
- High-Purity MPCVD PCD: Recommended for replicating or extending the study’s microcrystalline diamond growth on non-diamond substrates.
- High-Purity PCD with controlled nucleation: Suitable when dense seeding, continuous film coverage, and high sp3 content are the primary targets.
- Boron-Doped Diamond (BDD): Relevant for electrochemical, sensing, and electrode projects requiring conductive diamond while retaining CVD diamond’s chemical and electrochemical stability.
- Metallized diamond wafers: Applicable where subsequent device fabrication requires Au, Pt, Pd, Ti, W, or Cu contacts and patterned interfaces.
The closest 6CCVD match to this research is high-purity MPCVD PCD produced on seeded silicon or another compatible non-diamond substrate. The paper demonstrates that the quality of the final film depends strongly on seed dispersion, substrate pretreatment, growth duration, and nucleation bias; 6CCVD can support these process variables through controlled material specifications and custom deposition programs.
Customization Potential
Section titled “Customization Potential”- 6CCVD provides polycrystalline diamond plates and wafers up to 125 mm, enabling scale-up from laboratory coupons to larger process-development substrates.
- PCD thickness is available from 0.1 µm to 500 µm, covering the thin-film and free-standing regimes relevant to nucleation studies, sensors, electrodes, and protective coatings.
- Diamond substrates are available up to 10 mm thickness for applications requiring robust mechanical support or high-current thermal management.
- Material selection can be tailored among SCD, PCD, and BDD according to optical, electrical, thermal, and electrochemical requirements.
- Surface finishing supports Ra < 1 nm for SCD and Ra < 5 nm for inch-size PCD, allowing downstream characterization and bonding steps to be planned with controlled surface roughness.
- In-house metallization is available with Au, Pt, Pd, Ti, W, and Cu, supporting electrode fabrication and integration of diamond into MEMS, sensor, and semiconductor assemblies.
- Custom dimensions and diamond-on-silicon architectures can be specified for applications that require nucleation studies, thin-film coatings, or electrically active diamond layers.
- Laser cutting and related custom shaping services can be considered for defined geometries, device isolation, and packaged component formats.
Process and Engineering Recommendations
Section titled “Process and Engineering Recommendations”- Use DMSO-based or similarly finely dispersed nanodiamond seeds when the objective is to maximize nucleation density, film continuity, and relative sp3 content.
- Control seed agglomeration: the study indicates that smaller dispersed grain size is associated with better diamond ideality. 6CCVD engineering support can help specify colloid dispersion, seeding concentration, and substrate treatment procedures.
- Evaluate both 30-minute and 120-minute growth schedules to distinguish nucleation effects from grain-coalescence and film-thickness effects.
- Include a BEN-compatible process window when higher crystallinity and improved sp3/sp2 ratio are required. The reported −250 V condition provides a useful reference point, although actual bias optimization depends on reactor geometry, substrate conductivity, and plasma conditions.
- Monitor film quality by Raman spectroscopy: use the 1332 cm−1 diamond peak together with the D and G bands to track crystalline diamond content, disorder, and sp2-bonded carbon.
- For electrical or electrochemical applications, consider BDD or another engineered PCD grade rather than undoped microcrystalline diamond, particularly when conductivity and charge-transfer behavior are important.
- For optical or low-loss applications, specify high-purity SCD or optically controlled PCD and define surface roughness, thickness, and metallic-pattern requirements before deposition.
- 6CCVD’s in-house PhD team can assist with material selection for similar MPCVD diamond growth, thin-film diamond coating, sensor, electrode, and semiconductor integration projects, including recommendations on crystal grade, substrate, thickness, polishing, and metallization.
Representative Specification Checklist
Section titled “Representative Specification Checklist”| Project Requirement | Recommended 6CCVD Starting Point |
|---|---|
| High sp3 content and continuous PCD film | High-purity MPCVD PCD |
| Maximum crystalline and optical performance | Optical Grade SCD |
| Conductive diamond electrode or sensor | BDD |
| Laboratory-scale nucleation study | 0.1-500 µm PCD on custom substrate |
| Larger-area deposition or device development | PCD plate or wafer up to 125 mm |
| Low-roughness characterization surface | SCD Ra < 1 nm or inch-size PCD Ra < 5 nm |
| Electrical contact formation | Au, Pt, Pd, Ti, W, or Cu metallization |
| Mechanical support or thick diamond body | Diamond substrate up to 10 mm |
| Patterned device geometry | Custom dimensions and laser cutting |
For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
he in)uene of vrious nnodimond olloids used for seeding nondimond sustrtes in mirowve plsm enhned hemil vpour deposition dimond proess ws investigtedF golloids sed on deionized wterD isoE propnol lohol nd dimethyl sulfoxide @hwyA were used with di’erent grin size dispersionX ISHD RHH nd QS nmD respetivelyF he in)uene of growth time ws lso tken into onsidertion nd is enhned nuletionF wiroE rystlline dimond (lms were deposited on the seeded sustrtes in mirowve plsm hemil vpour deposition using hydrogen!methne gs mixtureF eeding e0ieny ws investigted y mens of snning eletron mirosopy nd mn spetrosopyF euthors de(ned the new ftor lled s dimond idelity ftor @diA whih n give quik estimtion of qulity of (lm nd reltive sp 3 ontentF pew min peks were identi(ed t the following wve numersX dimond sp 3 pek IQQP m -1 D D nd pek IQSS m -1 D g!r ending pek IRRH!IRVH m -1 nd G nd pek ISTH m -1 F he est di ws hieved for hwy sed olloid in ll sesF he pplition of is enhned nuletion inreses the dimond rystls size nd the sp 3 /sp 2 rtioF hysX IHFIPTWQGehysoleFIPVFIQT egX VIFISFqhD VIFHSFugD VPFVHFqkD TVFSSFe!