Skip to content

14 µm continuous-wave diamond Raman laser

MetadataDetails
Publication Date2017-12-01
JournalOptics Express
AuthorsRiccardo Casula, Jussi-Pekka Penttinen, Alan J. Kemp, Mircea Guină, Jennifer E. Hastie
InstitutionsUniversity of Strathclyde, Tampere University
Citations20
AnalysisFull AI Review Included

1.4 µm Continuous-Wave Diamond Raman Laser — Technical Documentation

Section titled “1.4 µm Continuous-Wave Diamond Raman Laser — Technical Documentation”
  • Milestone Achievement: First reported ~1.4 µm continuous-wave (CW) diamond Raman laser pumped by a semiconductor disk laser (SDL/VECSEL), extending the longest demonstrated wavelength for this architecture.
  • Output Performance: Maximum CW output power of 2.3 W with an optical conversion efficiency of 3.4 % relative to absorbed diode pump power.
  • Spectral Purity: Narrow Stokes emission with FWHM < 0.1 nm achieved using intracavity etalons to force single-etalon-peak fundamental operation.
  • Tunability: > 40 nm tuning range of the Raman laser via rotation of an intracavity birefringent filter tuning the SDL fundamental.
  • Architecture: Intracavity Raman conversion — the diamond crystal sits directly inside the SDL cavity, enabling high fundamental intensities for efficient Stokes shift.
  • Target Spectral Region: Eye-safe ~1.4 µm band, overlapping strong water-vapor absorption lines — directly relevant to atmospheric and water-vapor DIAL sensing.
  • Method: Linear SDL/Raman cavity with a low-loss CVD single-crystal diamond as the Raman gain medium, operated under CW 808 nm diode pumping.
ParameterValueUnitContext
Stokes (Raman laser) wavelength~1.4µmLongest CW diamond Raman emission reported
Maximum CW output power2.3WIntracavity Raman conversion
Optical conversion efficiency3.4%Relative to absorbed diode pump power
Stokes linewidth (FWHM)< 0.1nmWith intracavity etalons
Tuning range> 40nmVia intracavity birefringent filter rotation
Raman gain mediumSingle-crystal CVD diamond—Low-loss, high Raman gain
Pump architectureInGaAs-QW VECSEL (SDL)—Intracavity-pumped Raman
Diode pump wavelength808nmFiber-coupled pump diodes
SDL fundamental (pump for diamond)~1170nmTunable via birefringent filter
Raman shift (diamond)1332cm-1First-order Stokes shift
Output coupler transmissions tested1.5 % and ~4%Trade-off between power and linewidth
Diamond crystal lengths tested8 mm (50 + 100 µm étalons), 10 mm (250 + 200 µm étalons)mm / µmTwo cavity configurations reported
Pump power absorbed (max)up to ~60WFrom reported L-I curves
Operation modeContinuous-wave (CW)—Room temperature
  1. Gain Medium Selection: Low-loss single-crystal CVD diamond chosen for its exceptional Raman gain (1332 cm-1 first-order shift) and high thermal conductivity.
  2. Pump Source: Fiber-coupled 808 nm diode lasers used to optically pump an InGaAs-QW VECSEL (SDL) structure — providing a high-brightness, tunable ~1.17 µm fundamental.
  3. Intracavity Architecture: Diamond crystal placed directly inside the linear SDL cavity to maximize fundamental circulating power and exploit high intensity for efficient Raman conversion.
  4. Wavelength Tuning: Intracavity birefringent filter (BRF) rotated to tune the SDL oscillation wavelength (fundamental), which correspondingly shifts the Stokes output.
  5. Linewidth Narrowing: Solid etalons (e.g., 50 + 100 µm or 250 + 200 µm uncoated YAG etalons) inserted into the cavity to enforce single-etalon-peak fundamental operation and produce FWHM < 0.1 nm Stokes emission.
  6. Output Coupling Optimization: Output couplers with ~1.5 % and ~4 % transmission evaluated to balance output power against spectral purity.
  7. Performance Characterization: Output power measured vs. absorbed pump power; spectral characteristics recorded with optical spectrum analyzers; tuning curve correlated against water-vapor absorption features in the 1.4 µm band.
  8. Application Mapping: Stokes wavelength tuning mapped to atmospheric water-vapor absorption lines, demonstrating suitability for differential-absorption lidar (DIAL) and gas sensing.

The intracavity Raman architecture reported here places extreme demands on the diamond gain element — ultralow optical loss at the fundamental (~1.17 µm) and Stokes (~1.4 µm) wavelengths, exceptionally high Raman gain coefficient, and a thermal figure of merit compatible with multi-watt CW intracavity loading. 6CCVD manufactures the exact class of material this work depends on.

Applicable Materials

  • Optical-Grade Single-Crystal Diamond (SCD): Chemically vapor-deposited SCD with low nitrogen content and sub-ppm impurity levels is the material class used in this experiment. 6CCVD supplies optical-grade SCD in custom thicknesses from 0.1 µm to 500 µm, suitable for end-coupled or Brewster-configured Raman crystals.
  • Ultra-Low Surface Roughness (Ra < 1 nm): The intracavity insertion loss of the diamond is dominated by surface scattering. 6CCVD’s super-polished SCD surfaces (Ra < 1 nm) directly minimize round-trip loss and raise the slope efficiency achievable in this architecture.
  • Optional Heavy Boron-Doped PCD: Where cost-optimized Raman gain at slightly reduced efficiency is acceptable, 6CCVD’s boron-doped polycrystalline diamond (BDD) provides a robust alternative.

Customization Potential

  • Tailored Crystal Lengths: The paper reports diamond crystals of 8 mm and 10 mm. 6CCVD produces SCD in custom lengths and orientations engineered for low-birefringence propagation, enabling direct replication or extension to longer interaction lengths.
  • Custom Metalization: For researchers pursuing heat-spreader-bonded or mounted diamond configurations (e.g., into copper or tungsten carriers for high-thermal-load CW cavities), 6CCVD offers in-house Au, Pt, Pd, Ti, W, and Cu metalization with custom patterning.
  • Laser Cutting & Shaping: 6CCVD’s laser-cutting service delivers custom crystal geometries — including the Brewster facets, AR-coated end faces, and non-standard aspect ratios commonly required for intracavity Raman work.
  • Wafer & Plate Sizes: Single-crystal and polycrystalline diamond plates up to 125 mm (PCD) and bulk substrates up to 10 mm support everything from prototype resonators to production-scale cavity engineering.

Engineering Support

  • 6CCVD’s in-house PhD engineering team routinely supports researchers building CW and pulsed solid-state Raman lasers, gas-sensing lidar sources, and quantum/wavelength-conversion platforms.
  • We assist with material selection — SCD vs. BDD vs. PCD — based on your target Stokes wavelength (the 1332 cm-1 diamond shift scales the pump wavelength to any desired output), Raman gain requirements, and thermal-management constraints.
  • For atmospheric and water-vapor DIAL projects targeting the eye-safe 1.4 µm band, we can recommend specific SCD grades, thicknesses, and AR-coating strategies optimized for low loss and high damage threshold.

Call to Action

For custom diamond specifications, metalization options, or material consultation on your next Raman laser, water-vapor sensing, or intracavity frequency-conversion project, visit 6ccvd.com or contact our engineering team directly. Global shipping (DDU default; DDP available).

View Original Abstract

The longest wavelength (~1.4 µm) emitted by a diamond Raman laser pumped by a semiconductor disk laser (SDL) is reported. The output power of the intracavity-pumped Raman laser reached a maximum of 2.3 W with an optical conversion efficiency of 3.4% with respect to the absorbed diode pump power. Narrow Stokes emission (FWHM <0.1 nm) was attained using etalons to limit the fundamental spectrum to a single etalon peak. Tuning of the Raman laser over >40 nm was achieved via rotation of an intracavity birefringent filter that tuned the SDL oscillation wavelength.