Skip to content

DIAMOND DETECTOR TECHNOLOGY - STATUS AND PERSPECTIVES

MetadataDetails
Publication Date2018-01-01
JournalRAD Association Journal
AuthorsDmitry Hits
InstitutionsBoard of the Swiss Federal Institutes of Technology, ETH Zurich
AnalysisFull AI Review Included

Diamond Detector Technology: Status and Perspectives — Technical Documentation

Section titled “Diamond Detector Technology: Status and Perspectives — Technical Documentation”
  • Context: RD42 collaboration (CERN) evaluates CVD diamond for high-radiation, high-rate particle detection in collider environments (HL-LHC era).
  • Radiation Hardness: Damage model Qcoll = Q0 (1 − exp(−c·Φ)) validated across protons, neutrons, pions, and mixed fields; results from all species scale onto a single curve via relative damage factors.
  • Rate Performance: Un-irradiated polycrystalline CVD (pCVD) shows <5% pulse-height variation from 10 kHz/cm2 to 10 MHz/cm2; irradiated samples (<1% variation) remain stable across the full pion flux range (2 kHz/cm2 to 20 MHz/cm2).
  • 3D Pixel Demonstrator: First 3D laser-fabricated electrode structure in pCVD diamond with pixel readout, achieving 99.2% efficiency at -55 V bias in a 67 kHz/cm2 pion beam.
  • Electronics Integration: Custom readout with 6 ns peaking time, 20 ns return-to-baseline, 2 GS/s DRS4 digitization — proves diamond is compatible with high-luminosity, low-latency architectures.
  • Strategic Value: Diamond combines wide bandgap, high displacement threshold, low dielectric constant, and thermal conductivity — uniquely suited for 4D tracking, beam monitoring, and luminosity measurement beyond silicon’s operational envelope.
  • Key Result: Both planar (pad) and 3D (pixel) geometries function post-irradiation, making diamond a viable candidate for innermost tracker layers where radiation fluence exceeds silicon tolerance.

ParameterValueUnitContext
Particle species testedp, π+, n—Protons (24 GeV/c), pions (260 MeV/c), neutrons (reactor spectrum)
Particle flux range (rate scan)2 × 103 to 2 × 107Hz/cm2Pad detector rate dependence study
Pulse-height variation, un-irradiated&lt;5 (≈2)%Over 10 kHz/cm2 - 10 MHz/cm2
Pulse-height variation, irradiated&lt;1%Over 10 kHz/cm2 - 10 MHz/cm2
Neutron fluence range5 × 1013 to 4 × 1015n/cm2Irradiated sample set
Proton fluence range0 - ~8 × 1015p/cm224 GeV/c protons
Readout peaking time6nsCharge-sensitive amplifier
Return-to-baseline20nsAmplifier settling
Digitizer sampling rate2GS/sDRS4 evaluation board
Pad electrode geometry3.5 × 3.5mm2With guard ring
3D detector dimensions5 × 5 × 0.5mm3pCVD substrate
3D electrode column diameter&le;1µmFemtosecond laser focal spot
Laser wavelength / pulse800 / 100nm / fsFemtosecond laser graphitization
Laser scan speed10µm/sSample translation through focal volume
Electrode bulk resistivity0.1 - 1Ω·cmLaser-induced graphitic columns
Electrode termination depth15µmBelow opposite surface (avoids shorting)
3D cell pitch50 × 50µm24 bias + 1 readout per cell
Active 3D area3.0 × 3.1mm260 × 62 cells
Readout electrode ganging6cellsPitch-matched to PSI46dig chip (150 / 100 µm)
Readout chip threshold1500e-PSI46dig
3D detector bias-55VOperating voltage
3D detector efficiency99.2%At 67 kHz/cm2 pion flux
Hit position resolution~100µmLimited by multiple scattering at PSI
Damage constant λ0 (fit)species-dependentµmMean free path at zero fluence
Damage factor relative to 24 GeV pTabulated—24 GeV p normalized to 1.00

  1. Material Selection: Optical / detector-grade polycrystalline CVD diamond from industrial suppliers; pre-selected on leakage current and CCD (charge collection distance) performance.
  2. Planar Pad Fabrication: Double-side metallization with a 3.5 × 3.5 mm2 pad electrode surrounded by a guard ring; contacts stripped prior to irradiation, re-metallized post-irradiation.
  3. Irradiation Protocol: Sequential exposures at Jožef Stefan Institute (reactor neutrons) and CERN PS (24 GeV/c protons); contacts removed between irradiations to accelerate polarization “pumping” (cool-down).
  4. Damage Model Fitting: Exponential saturation law Qcoll = Q0(1 − exp(−Φ/Φ0)); data from all species scaled by relative damage factor onto a universal curve.
  5. Beam Test (Rate Scan): πM1 beamline at PSI HIPA accelerator, π+ momentum 260 MeV/c; flux varied from 2 kHz/cm2 to 20 MHz/cm2 via two collimator sets; pulse height normalized to lowest-rate anchor point.
  6. Tracking Reference: 4-plane beam telescope (2 upstream + 2 downstream) with PSi46v2 analog pixel readout; hit resolution ~100 µm at DUT plane.
  7. 3D Electrode Fabrication: Femtosecond laser (100 fs, 800 nm, ≤1 µm spot, 10 µm/s scan) writes graphitic columns (0.1-1 Ω·cm) directly into the diamond bulk; bias and readout columns offset so each terminates 15 µm below the opposite surface.
  8. 3D Cell Geometry: Four bias columns arranged in 50 × 50 µm2 square with a single readout column at the cell center; columns ganged 6:1 to match PSI46dig chip pitches.
  9. Signal Chain: Broadband amplifier (6 ns peaking) → DRS4 digitizer (2 GS/s) → offline pulse-height extraction; threshold 1500 e- for pixel efficiency counting.
  10. Efficiency Definition: Hit within ~1000 µm of predicted telescope position inside fiducial region (excludes hot/dead pixels and bump-bonding defects).

The RD42 results place extreme, highly specific demands on diamond material — demands that map directly onto 6CCVD’s production portfolio.

  • Polycrystalline CVD Diamond (PCD), Optical / Detector Grade: Required for both the planar pad geometry (3.5 × 3.5 mm2) and the 5 × 5 × 0.5 mm3 3D pixel substrate. 6CCVD supplies inch-class free-standing PCD wafers with Ra < 5 nm post-polish, well within the surface-quality window needed for uniform metallization and reproducible laser graphitization.
  • Single Crystal CVD Diamond (SCD): Referenced as the prior benchmark for 3D devices. 6CCVD optical-grade SCD (Ra < 1 nm) is suitable when charge collection uniformity at the level of a few µm matters more than raw area.
  • Boron-Doped Diamond (BDD): For groups extending this work into fully ohmic pixel architectures or strip detectors, our heavy-boron p-type PCD/SCD provides low-resistivity contact-grade material.
  • Geometry & Thickness: Planar pads in this work are 300-500 µm; 3D substrates are 500 µm. 6CCVD ships PCD and SCD from 0.1 µm to 500 µm and substrates up to 10 mm, with free-standing plates/wafers to 125 mm — meaning 3D detector arrays can be scaled well beyond the 3.0 × 3.1 mm2 active area demonstrated here.
  • Metallization (Internal Capability): The paper uses single-pad metallization with guard rings; pad and pixel layouts typically require Ti/Pt/Au or Cr/Au stacks with patterned photolithography. 6CCVD offers in-house Au, Pt, Pd, Ti, W, Cu metallization with custom pad, pixel, or guard-ring geometries — no foundry hand-off required.
  • Laser Cutting & Shaping: Pixelated and small-format samples need low-damage dicing. 6CCVD’s laser cutting service delivers clean edges on free-standing diamond down to sub-mm dimensions, suitable for individual pixel modules or hybrid bump-bonding layouts (50 × 50 µm2 cell pitch compatible).
  • Bulk Electrode Machining Path: 3D graphitic columns were written here by femtosecond laser. While 6CCVD’s core offering is material supply and metallization, we can supply pre-qualified pCVD coupons matched to the 0.1-1 Ω·cm column resistivity specification and partner with femtosecond-laser houses for full 3D fabrication.
  • Material Selection Consultation: Whether your project demands the planar pad geometry of Section 3 or the laser-patterned 3D cell architecture of Section 4, 6CCVD’s in-house PhD engineering team can advise on:
    • PCD vs. SCD selection based on CCD, leakage current, and operating bias (this paper operates at -55 V; thin SCD supports equivalent fields at lower voltage).
    • Thickness vs. active-area trade-offs for high-rate MIP detection.
    • Metallization stack compatibility with bump-bonding processes (PSI46dig-class pixel readout).
  • Radiation Hardness Studies: Our materials are characterized for displacement-damage-relevant defects; we can supply matched unirradiated/irradiated test splits for groups replicating the RD42 protocol.
  • Detector-Grade Quality Control: 6CCVD can deliver pre-screened material with documented leakage current and CCD maps, removing the “pre-selection” yield loss the paper describes.
RD42 ComponentRecommended 6CCVD Product
Planar pad detector (3.5 × 3.5 mm2)PCD plate, 300-500 µm, polished both sides, custom Ti/Pt/Au pad + guard-ring metallization
3D pixel substrate (5 × 5 × 0.5 mm3)Free-standing optical-grade PCD, 500 µm, Ra < 5 nm, laser-diced to size
Irradiation-control comparisonMatched pair: un-irradiated + pre-irradiated BDD or PCD samples
4D / beam-monitoring variantSCD membrane, 50-100 µm, custom pixel metallization

For custom specifications, metallization layouts, detector-grade PCD/SCD sourcing, or material consultation, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

The radiation tolerance of chemical vapor deposition (CVD) diamond against different particle species and energies has been studied in beam tests and is presented. We also present beam test results on signal size as a function of incident particle rate in charged particle detectors based on un-irradiated and irradiated poly-crystalline CVD diamond over a range of particle fluxes from 2 kHz/cm 2 to 20 MHz/cm 2 . The pulse height of the sensors was measured using readout electronics with a peaking time of 6 ns. In addition, the functionality of poly-crystalline CVD diamond 3D devices is demonstrated in beam tests and 3D diamond detectors are shown to be a promising technology for applications in future high rate/high intensity experiments.