Field Assisted Photoemission from Nanocrystalline Diamond and Diamond Field Emitter Arrays
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2018-08-01 |
| Authors | Vitaly Pavlenko, Heather Andrews, Robert Aragonez, Ryan Fleming, Chengkun Huang |
| Institutions | Los Alamos National Laboratory |
| Analysis | Full AI Review Included |
Executive Summary
Section titled “Executive Summary”- The study evaluates field-assisted photoemission from nanocrystalline diamond and diamond field-emitter arrays (DFEAs) for potential dielectric laser accelerator (DLA) electron sources.
- Diamond combines strong UV photoemission with a low electron affinity, enabling measurable electron emission near the diamond band-gap energy.
- A Xe-lamp/monochromator system was developed to measure quantum efficiency (QE) across 195-270 nm, with electric fields extending to 2.6 MV/m in the reported comparative data.
- The tested field range was selected to remain below the regime where strong DC field emission produces continuous background current; fields above several MV/m were therefore not investigated in this study.
- Samples included a flat nanocrystalline diamond cathode and a DFEA containing thousands of micron-scale pyramids with nanometer-scale emitting tips. The DFEA pyramid base size was 20 µm.
- The work provides a basis for engineering photo-gated, bright, coherent electron beams, while identifying the need for further investigation of individual diamond tips and their response under focused laser excitation.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Wavelength scan range | 195-270 | nm | Spectral response of diamond and DFEA samples |
| Photon-energy range, approximate | 4.6-6.4 | eV | Corresponding to 270-195 nm |
| Maximum investigated electric field | 2.6 | MV/m | Highest field shown for comparative field-assisted photoemission data |
| Maximum selectable cathode bias | 650 | V | Battery-powered source in the experimental system |
| Initial conventional field limit | 1 | kV/m | Earlier low-field photoemission setup |
| Field range originally specified for system | Up to 5 | MV/m | Design capability of the field-assisted setup |
| Illumination spot | Approximately 1 × 1 | mm | Imaged onto the cathode through the chamber viewport |
| Flat diamond sample size | Approximately 5 × 5 | mm | Used for comparison with the DFEA |
| DFEA pyramid base size | 20 | µm | SEM-observed emitter geometry |
| DFEA sample architecture | Thousands of pyramids | — | Designed to provide sufficient emission area for tunable-source testing |
| Monochromator output calibration | Performed before QE measurements | — | Required because the output included a broad-spectrum parasitic component |
| Optical modulation | Chopper and lock-in amplifier | — | Used because UV output power was very low, especially at short wavelengths |
| Illumination configuration | Xe lamp coupled to monochromator | — | Tunable, incoherent UV excitation |
| Emission regime | Field-assisted photoemission | — | Near the photoelectric threshold, with expected Schottky enhancement |
| Potential crossover regime | Several MV/m and above | — | Strong DC field emission may produce undesirable continuous background current |
| Reported sample fabrication method | Same diamond deposition process for flat and DFEA samples | — | Enables comparative material testing |
| Photoelectric threshold example | Approximately 5.4 | eV | Fowler-plot fit for flat nanocrystalline diamond |
| Relevant diamond band-gap energy | Approximately 5.4-5.5 | eV | Consistent with the observed photoemission threshold |
Key Methodologies
Section titled “Key Methodologies”-
Sample preparation
- Fabricate flat nanocrystalline diamond and DFEA samples using the same diamond deposition process.
- Fabricate the DFEA with thousands of pyramidal emitters, each having a 20 µm base and a nanoscale tip.
-
Initial photoemission characterization
- Characterize conventional photoemission using a low-field setup with electric fields up to 1 kV/m.
- Analyze the spectral response using a simplified Fowler plot.
- Determine a representative photoemission threshold of approximately 5.4 eV, close to the diamond band gap.
-
Field-assisted test assembly
- Use a negatively biased diamond cathode positioned close to a transparent metal-mesh anode.
- Select cathode bias up to 650 V using a battery-powered source.
- Control the anode-cathode spacing to achieve fields in the MV/m range.
- Align the cathode and mesh precisely using micrometer adjustments and microscope-camera observation.
-
UV excitation
- Use a tunable Xe lamp coupled to a single-grating monochromator.
- Scan the wavelength from 195 to 270 nm.
- Image the monochromator output slit onto the sample through the chamber viewport.
- Maintain an illumination spot of approximately 1 mm².
-
Power and signal measurement
- Calibrate the monochromator output before calculating QE.
- Separate the selected UV line from the substantial longer-wavelength parasitic component.
- Modulate the incident optical power with an optical chopper.
- Detect the resulting photocurrent with a lock-in amplifier.
- Account for reduced measurement accuracy from 230-270 nm because chromatic aberration caused illumination-spot expansion and defocusing.
-
Comparative measurement
- Measure flat nanocrystalline diamond and DFEA samples under matched deposition and optical conditions.
- Compare QE as a function of wavelength, photon energy, and applied electric field.
- Evaluate field enhancement while limiting the field to 2.6 MV/m for the presented data to avoid continuous DC field-emission background.
-
Mechanistic interpretation
- Compare the response with the three-step photoemission model expected for a wide-bandgap semiconductor with low electron affinity.
- Evaluate the expected contribution of the Schottky effect at field-enhanced emitter tips.
- Consider the crossover between photoemission and field emission at higher electric fields.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”Applicable Materials
Section titled “Applicable Materials”| Research requirement | Recommended 6CCVD material | Rationale |
|---|---|---|
| Flat nanocrystalline diamond reference cathode | Optical-grade nanocrystalline PCD | Provides a planar diamond surface suitable for QE baseline and UV spectral-response measurements |
| Diamond field-emitter arrays | Patterned nanocrystalline PCD with engineered emitter geometry | Supports arrays of pyramidal or tip-enhanced structures requiring micron-scale control |
| Enhanced emission near the diamond photoelectric threshold | UV-optimized SCD or optical-grade PCD | Low electron affinity and strong UV response are central to field-assisted photoemission |
| Stable high-field operation | High-quality SCD or engineered PCD | Material selection can be optimized for mechanical integrity, surface quality, and emission stability |
| Integrated electrical contacts | Metalized SCD or PCD | In-house metalization supports defined cathode interfaces and biasing |
| Higher-current or surface-conduction applications | Boron-doped diamond, or BDD PCD | Doping can be considered when conductivity and charge transport are critical |
For a direct replication of the paper’s comparative study, optical-grade nanocrystalline PCD is the most appropriate starting material. For single-emitter or reduced-area photocathode development, SCD may offer advantages where controlled surface quality, low defect density, and predictable electronic behavior are priorities.
Recommended 6CCVD Specification Path
Section titled “Recommended 6CCVD Specification Path”| Specification category | 6CCVD capability | Recommended design consideration |
|---|---|---|
| Material | SCD, PCD, and BDD | Select according to optical response, conductivity, emitter geometry, and required surface quality |
| Plate or wafer dimensions | Up to 125 mm for PCD | Enables larger-area comparison studies, multi-sample arrays, and scalable emitter layouts |
| Diamond thickness | SCD: 0.1-500 µm; PCD: 0.1-500 µm | Supports thin free-standing photocathodes and thicker mechanically stable substrates |
| Substrate thickness | Up to 10 mm | Useful for robust mounting and high-voltage handling |
| Surface finish | SCD Ra < 1 nm; inch-size PCD Ra < 5 nm | Important for minimizing surface contamination, uncontrolled work-function variation, and optical scattering |
| Electrical metalization | Au, Pt, Pd, Ti, W, and Cu | Supports cathode electrodes, contact pads, shielding, and anode/cathode integration |
| Patterning and shaping | Custom dimensions and laser cutting | Enables tailored DFEA footprints, isolation features, electrode openings, and multiple test coupons on one diamond plate |
| Quantity and format | Custom plate, wafer, or component format | Can support research samples, development arrays, and pilot-scale production |
| Global delivery | DDU by default; DDP available | Facilitates international delivery of experimental and prototype components |
Customization Potential
Section titled “Customization Potential”The experiment requires precise control of:
- Emitter geometry: Pyramid base size, tip radius, pitch, array density, and active area.
- Surface condition: Surface termination, roughness, contamination level, and optical quality.
- Electrical architecture: Cathode contact material, contact geometry, spacing, and mesh integration.
- Optical geometry: Active-area dimensions, illumination alignment, and sample flatness.
- Field handling: Gap uniformity, substrate thickness, edge quality, and dielectric or conductive behavior.
6CCVD can provide custom SCD or PCD plates, selected metalization stacks such as Ti/Pt/Au, and laser-cut outlines or isolation features. A typical development sequence could begin with planar optical-grade PCD reference coupons, followed by patterned DFEA prototypes and then larger-area array designs.
Engineering Support
Section titled “Engineering Support”6CCVD’s in-house PhD team can assist with material selection for similar field-assisted diamond photocathode and dielectric laser accelerator projects, including:
- Defining SCD versus PCD based on optical and electronic requirements.
- Selecting the appropriate surface roughness and thickness.
- Designing metalization layouts for high-voltage cathode operation.
- Recommending emitter-array dimensions and active-area formats.
- Evaluating whether boron doping is needed for conductivity or charge extraction.
- Supporting custom sample layouts for wavelength-dependent QE measurements.
- Advising on the transition from millimeter-scale DFEA testing to single-tip or focused-beam experiments.
Recommended Development Approach
Section titled “Recommended Development Approach”| Phase | Proposed activity | 6CCVD contribution |
|---|---|---|
| 1. Baseline calibration | Fabricate planar optical-grade PCD reference samples | SCD/PCD thickness, size, and Ra specification control |
| 2. Electrical integration | Add cathode contacts and optical opening | Ti, Pt, Au, Pd, W, or Cu metalization options |
| 3. DFEA prototype | Produce patterned emitter arrays with controlled pyramid geometry | Custom PCD patterning, laser cutting, and dimensional engineering |
| 4. Comparative QE testing | Measure planar and DFEA samples over 195-270 nm and up to 2.6 MV/m | Material and geometry iteration support |
| 5. Single-tip development | Reduce active area for focused UV or laser excitation | Small-feature SCD/PCD preparation and custom contact design |
| 6. Scale-up | Increase array area while preserving field uniformity | PCD plates up to 125 mm and custom laser-cut layouts |
For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
Field emission from nanocrystalline diamond and especially from diamond field emitters is known to have an onset at low electric fields of a few MV/m, although the discussion on the agreement of the results with the classical Fowler-Nordheim model is still pending. While measurements of pure photoemission from flat nanocrystalline diamond agree reasonably well with the 3-step photoemission model for the wide bandgap semiconductor with low electron affinity, we are not aware of systematic studies of photoemission in the ~0.1-5 MV/ m range, where the electron emission mechanism is expected to be affected by the Schottky effect and crossover with the field emission. In order to understand applicability of field enhanced photoemission from diamond to generation of bright coherent photo-gated electron beams suitable for dielectric laser accelerators, we have designed a system to measure spectral response (quantum efficiency vs wavelength) of ~mm-sized samples with up to 5 MV/ m electric field in the anode-cathode gap. The system is based on an incoherent Xe lamp-based tunable ultaviolet light source, therefore relatively large and dense diamond field emitter arrays are required for comparative studies of arrays versus flat nanocrystalline diamond samples. We present the results of our original measurements in the range between 195 nm and 270 nm. Potential schemes of laser-triggered photoemission from a single diamond field emitter tip are discussed in view of the obtained results.
Tech Support
Section titled “Tech Support”Original Source
Section titled “Original Source”References
Section titled “References”- 1965 - Ionization in the Field of a Strong Electromagnetic Wave
- 2013 - Demonstration of electron acceleration in a laser-driven dielectric microstructure [Crossref]