Skip to content

Phase transitions and critical phenomena of tiny grains carbon films synthesized in microwave‐based vapor deposition system

MetadataDetails
Publication Date2018-11-28
JournalSurface and Interface Analysis
AuthorsMubarak Ali, I‐Nan Lin
InstitutionsTamkang University, COMSATS University Islamabad
Citations72
AnalysisFull AI Review Included
  • Phase-Transition Mapping: Establishes a direct correlation between chamber pressure (100-200 torr) and the resulting state behavior of carbon atoms in tiny grains, distinguishing graphitic, lonsdaleite, diamond, fullerene, and graphene phases via Raman and EELS spectroscopy.
  • Electron Field Emission (EFE) Tuning: Demonstrates that altering chamber pressure and hydrogen concentration shifts the “turn-on field” by a factor of >2× (from 11.52 V/µm at 100 torr to 25.00 V/µm at 150 torr with 6% H2).
  • Argon-Rich / Hydrogen-Poor Regime: Validates low-temperature (<700°C) MPCVD synthesis of UNCD/NCD-type films in 93% Ar / 1% CH4 / 6% H2 plasmas, directly relevant to cold-plasma engineered carbon electronics.
  • Elongated Graphite Structure Hypothesis: Proposes a mechanism where atoms in one-dimensional arrays stretch under surface-format forces to form “smooth element” structures, accelerating photonic current propagation — a design lever for cold cathodes and photonic devices.
  • Reproducible Process Window: Microwave power 1100-1400 W, pressure 100-200 torr, 60 min deposition on nucleated N-type Si (ρ 1-5 Ω·cm) yield consistent sub-10 nm grain films.
  • Multi-Wavelength Raman Sensitivity: Peak intensity of the v1 band (~1145 cm-1) shifts with excitation wavelength (325 nm vs 632.8 nm), highlighting the need for wavelength-matched characterization when benchmarking emitter-grade carbon films.
ParameterValueUnitContext
Microwave frequency2.45GHzIPLAS-Cyrannus MVD system
Microwave power range1100 - 1400WProcess sweep across all samples
Chamber pressure sweep100 - 200torrPrimary independent variable
Total mass flow rate200sccmHeld constant
Ar : CH4 : H2 ratio (primary)186 : 2 : 12sccm93% Ar / 1% CH4 / 6% H2
Ar : CH4 ratio (no H2)196 : 4sccmSample 4 — v1 enhancement test
Ar : CH4 ratio (EFE-only sweep)198 : 2 / 192 : 2 : 6 / 186 : 2 : 12sccmSamples 5-13
Substrate temperature (with H2)700 ± 10°CK-type thermocouple reading
Substrate temperature (no H2)500 ± 10°CReduced plasma heating (Ar thermal conductivity)
Nucleation duration30minNanodiamond (~30 nm) + Ti (325 mesh) seed
Deposition duration60minGrowth phase
SubstrateN-type Si, ρ 1-5Ω·cm(100) wafer, ultrasonic pre-clean
Turn-on field (100 torr, 6% H2)11.52V/µmLowest in study
Turn-on field (150 torr, 6% H2)25.00V/µmHighest with H2
Turn-on field (200 torr, 6% H2)16.40V/µmMid-range
Max current density (100 torr)> 2.0mA/cm2EFE superior sample
EFE vacuum level10-6torrKeithley 237 parallel-plate
HR-TEM accelerating voltage200kVJEOL JEM-2100F
Raman laser wavelengths325 / 632.8nmUV and visible
Core-loss EELS σ* band edge~292eVDiamond-phase indicator
Core-loss EELS π* dip (graphitic)~285eVElongated-graphite signature
Core-loss EELS graphene peak~328eVHighest-energy band
v1 peak (elongated graphite)~1145 / 8734cm-1 / nmLowest wave number → longest λ
D* peak (lonsdaleite)~1310 / 7634cm-1 / nmHexagonal diamond phase
D peak (diamond)~1332 / 7508cm-1 / nmCubic diamond phase
v2 peak (fullerene)~1480 / 6757cm-1 / nmLow-intensity band
G peak (graphene)~1580 / 6329cm-1 / nmHighest wave number → shortest λ
Grain size range2 - 10nmUNCD/NCD regime
  1. Substrate Preparation: N-type Si (ρ 1-5 Ω·cm) ultrasonically seeded in methanol with ~30 nm nanodiamond + 325-mesh Ti powder for 30 min to create high-density nucleation sites.
  2. Chamber Loading & Pump-Down: Substrate loaded into IPLAS-Cyrannus 2.45 GHz MPCVD chamber; baseline vacuum established prior to plasma ignition.
  3. Nucleation Phase: 30 min bias-free nucleation at the target gas mixture to drive high re-nucleation rate (essential for sub-10 nm grains).
  4. Growth Phase: 60 min deposition at fixed total flow 200 sccm, sweeping pressure 100 / 150 / 200 torr and microwave power 1100-1400 W.
  5. Gas Chemistry Sweep: Five distinct Ar:CH4:H2 ratios evaluated — primary (186:2:12), H2-free (196:4), and three EFE-only subsets (198:2:0, 192:2:6, 186:2:12 at 1200 W).
  6. In-Process Monitoring: Substrate temperature logged via K-type thermocouple (700 ± 10°C with H2; 500 ± 10°C without H2).
  7. Surface Imaging: ZEISS SIGMA scanning electron microscope for grain morphology across pressure points.
  8. Raman Spectroscopy: Renishaw inVia (325 nm) and HR800 UV (632.8 nm) for v1, v2, D*, D, and G band identification.
  9. HR-TEM / SAED: JEOL JEM-2100F at 200 kV for bright-field, high-resolution lattice imaging, and selected-area photon reflection patterns.
  10. EELS Analysis: Core-loss and low-loss photon energy loss spectroscopy for σ*, π*, and graphene-band mapping.
  11. Electron Field Emission Test: Tunable parallel-plate diode under 10-6 torr, Keithley 237 electrometer, turn-on field defined at standard threshold.

Applicable Materials

The sub-10 nm grain morphology and argon-rich / hydrogen-lean plasma regime described in this work map directly onto 6CCVD’s Polycrystalline Diamond (PCD) and Ultra-Nanocrystalline Diamond (UNCD) product lines. For cold-cathode and field-emission device replication, 6CCVD’s Optical Grade Polycrystalline Diamond (PCD) wafers — with grain sizes tunable down to the UNCD regime — provide the necessary sp3/sp2 grain-boundary architecture. Researchers investigating the “elongated atoms graphite structure” mechanism or seeking enhanced EFE turn-on fields below 15 V/µm should evaluate our fine-grain PCD films deposited on standard Si substrates, available in thicknesses from 0.1 µm to 500 µm. For devices that demand metallic-like conductivity without sp2 phase instability, our Heavy Boron-Doped Polycrystalline Diamond (BDD) delivers tunable resistivity while preserving the diamond-state atom content discussed in the paper’s Table 2.

Customization Potential

The paper’s recipe requires non-standard Si substrate geometries (small coupons) and a Ti-assisted nanodiamond seeding protocol that can be readily transferred to customer-supplied wafers. 6CCVD routinely delivers:

  • Custom plate dimensions up to 125 mm for PCD, including the (100)-oriented N-type Si used here.
  • In-house metallization (Au, Pt, Pd, Ti, W, Cu) — directly relevant to the paper’s discussion of Au-UNCD vs Cu-UNCD emitter contacts (Refs. [27, 29, 30]). Ti adhesion layers followed by Au or Pt capping can be deposited to match the bias-enhanced nucleation interface studied.
  • Laser cutting and dicing to arbitrary coupon dimensions for multi-pressure test matrices.
  • Thickness control from 0.1 µm to 10 mm substrates — enabling freestanding membrane architectures analogous to the homojunction UNCD devices cited (Ref. [20]).
  • Surface polishing to Ra &lt; 5 nm on inch-scale PCD, critical for reproducible EFE turn-on fields where surface graphitic phase density dominates emission.

Engineering Support

The paper’s central claim — that EFE performance tracks the population of elongated-graphite-structure grains — implies that minor shifts in gas chemistry, pressure, or substrate temperature can swing turn-on field by 2× or more. 6CCVD’s in-house PhD engineering team can assist with:

  • Material selection between SCD, PCD, and BDD for the specific EFE / photonic current propagation regime under investigation.
  • Recipe replication and extension — translating the 100-200 torr, 1100-1400 W, 6% H2 Ar/CH4 window onto customer-furnace baselines.
  • Metallization stack design for cathode interfaces, including the Ti/Au bilayer structures the paper highlights for low work-function contacts.
  • Multi-wavelength Raman benchmarking using customer-preferred laser lines (325 nm vs 632.8 nm) prior to shipment.

Call to Action

For custom specifications, metallization stacks, or material consultation on field-emission-grade UNCD/NCD films and freestanding diamond membranes, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

Different peak trends of tiny grains carbon film have been observed under the investigations of the Raman spectroscopy and energy loss spectroscopy. Carbon films known in nanocrystalline and ultrananocrystalline diamond films are synthesized by employing microwave‐based vapor deposition system. Carbon atoms exhibit several state behaviors depending on the incurred positions of their electrons. Different morphology of tiny grains under different chamber pressure is related to different rate of arriving typical energies at/near substrate surface. Those tiny grains of carbon film, which evolved in graphitic state atoms are converted to structure of smooth elements where elongation of atoms of one‐dimensional arrays is as per exerting surface format forces along opposite poles from their centers. Such tiny grains in the film are the cause of v 1 peak under the investigation of the Raman spectrum because of the enhanced propagation of input laser signals through channelized inter‐state electron gaps of elongated graphitic state atoms. Those tiny grains of carbon film, which evolved in fullerene state are the cause of v 2 peak. The tiny grains related to v 1 peak possess a low intensity as compared with the ones which comprised atoms having state behaviors known in their exceptional hardness. Tiny grains representing v 1 peak in the Raman spectrum are also the cause of field emission characteristic of a carbon film. Different peak recordings were made for the Raman at defined positions indicating a different state of carbon atoms for a different phase of deposited tiny grains, which is in line to their energy loss spectroscopy.

  1. 2018 - Nanoparticles‐photons: effective or defective nanomedicine