Skip to content

Solid-state maser with microwatt output power at moderate cryogenic temperatures

MetadataDetails
Publication Date2025-11-01
JournalAIP Advances
AuthorsYefim Varshavsky, Oleg Zgadzai, Aharon Blank
InstitutionsTechnion – Israel Institute of Technology
AnalysisFull AI Review Included
  • Breakthrough Output Power: The paper demonstrates a continuous-wave, diamond-based maser oscillator achieving > −30 dBm (1 µW) output power at ~14.5 GHz — a two-orders-of-magnitude improvement over previous diamond- or ruby-based solid-state maser oscillators.
  • Moderate Cryogenic Operation: Stable maser action achieved at ~180 K, enabled by Stirling-type cryocoolers without the need for liquid helium — a major practical advantage over ruby masers (~1.5 K).
  • Key Material Platform: Optically pumped [111]-oriented, NV-rich single-crystal diamond (SCD) integrated into a compact high-Q metallic microwave cavity (Q ~ 2460).
  • Optical Pumping Architecture: Sustained high-power green LED excitation (> 1 W per LED, ~1.2 W typical) with efficient light coupling and thermal dissipation grids.
  • Phase Noise Potential: Leeson-model projections indicate that coupling to an ultra-high-Q external sapphire resonator (Q ~ 108) could push single-sideband phase noise toward ~ −150 dBc at 50 K.
  • Engineering Roadmap Identified: Further enhancement requires NV-doping optimization, NV-center orientation control, resonator geometry refinement, magnetic field stabilization, and feedback locking to high-Q external resonators.
  • Application Target: Ultra-low phase noise microwave sources for metrology, radar, atomic clocks, and deep-space communication — especially attractive at frequency offsets below 104 Hz.
ParameterValueUnitContext
Operating Frequency (f0)~14.5GHzMaser oscillator center frequency
Output Power (sustained)> −30 dBm (1 µW)dBm / µW100× improvement over prior diamond masers
Output Power (prior best)~−54.1 dBmdBmReference 8 (Zollitsch et al., 2023)
Output Power (ruby maser, typical)~10−9 WWReference 10 — 1.5 K operation
Operating Temperature~180KModerate cryogenic, Stirling-cooler compatible
Projected Operation Temperature50 - 77KFuture Stirling-cooled operation
Resonator Q (in-house metallic cavity)~2460—Compact cylindrical cavity
External Coupling Q (Qext, projected)2 × 106 - 108—Sapphire resonator coupling
Spin Temperature (Tm)~0.65KApproaching quantum limit (Ref 3)
Maser Noise Temperature (Tmaser)~4.5KAt T0 = 77 K
System Noise Temperature (Tsys, nominal)81.5KFor Leeson-model estimates
LED Optical Excitation Power440 mW - 1.2 WWPer LED, 532 nm (green)
LED Threshold Power~60mWPer LED
Frequency Jitter (high excitation)~1MHzAt ~1.2 W LED excitation
Frequency Jitter (low excitation)~10kHzNear oscillation threshold
Coupling Factor (ε)0.05—Cavity Q ~ 20× Qm ~ 100
Flicker Corner Frequency (fc)300HzLeeson-model assumption
Ultimate Phase Noise Projection~−150dBcThermally limited at 180 K
Diamond Crystal Orientation[111]—NV-center alignment for optimal pumping
Amplifier Used (preamp)LNF-LNC6_20A—Low Noise Factory, Sweden
  1. Diamond Material Selection

    • Optically pumpable, NV-rich single-crystal diamond, [111]-oriented to align NV axes with the static magnetic field for maximum population inversion efficiency.
    • Diamond crystals characterized by ESR to confirm NV concentration and spin Hamiltonian parameters.
  2. Microwave Cavity Fabrication

    • Compact, high-Q (~2460) metallic cylindrical cavity machined to support the ~14.5 GHz maser mode.
    • Cavity designed with an optical grid / dielectric window for efficient green-light delivery and thermal dissipation channels to manage the high LED pump power.
  3. Optical Pumping Configuration

    • Cost-effective green LEDs (532 nm) with > 1 W sustained output per LED (typically 1.2 W operational).
    • Direct illumination through lid window onto the diamond sample positioned at the cavity’s H-field maximum.
  4. Magnet & Cooling Setup

    • Superconducting magnet in persistent mode for static field stability (replacing the noisier electromagnet).
    • Variable-temperature cryostat at ~180 K for maser oscillation tests; phase-noise projections target 77 K and 50 K with Stirling coolers.
  5. Signal Acquisition & Analysis

    • Frequency-domain: Spectrum analyzer sweeps across 14.47-14.48 GHz to verify oscillator output.
    • Time-domain: Direct oscilloscope capture of amplitude envelope and frequency jitter (~10 µs - 100 µs windows).
    • Phase-noise mode: LNA preamplification (LNF-LNC6_20A) required to overcome analyzer thermal noise floor when operating near threshold (~ −70 dBm).
  6. Phase-Noise Modeling (Leeson Equation)

    • Single-sideband phase noise:
      L(fm) = 10·log10[(F·kB·Tsys/2·Pin) · (1 + (f0/2·Qext·fm)2) · (1 + fc/fm)]
    • Assumes Pin = 0.1 µW, Qext = 2 × 106 (nominal) or 108 (ultimate), fc = 300 Hz.
    • Comparison benchmarked against ruby maser at ~2.6 GHz, Q ~ 109, 1.5 K.
Paper Requirement6CCVD Equivalent
[111]-oriented NV-rich single-crystal diamondOptical Grade SCD — custom-oriented single-crystal diamond substrates, [100] / [110] / [111] orientations available
High NV− density for spin inversionNV-Doped SCD — controlled N+ implantation + annealing services
Dielectric / low-loss diamond for cavity integrationHigh-Purity SCD (Ra < 1 nm polished) — minimal microwave loss tangent
Sample dimensions fitting cavity geometryCustom SCD dimensions up to 10 mm thickness, plates/wafers to 125 mm (PCD)
  • Recommended 6CCVD Stock: [111]-oriented HPHT or CVD-grown single-crystal diamond, electron-irradiated and annealed to render NV centers at the required density (typically 1-100 ppm). For ultra-low-loss MW operation, 6CCVD Optical Grade SCD with sub-ppm nitrogen is recommended as the bulk substrate, with a thin NV-enriched layer bonded to the cavity face.
  • Crystal Orientation: 6CCVD offers laser-cutting and dicing services to deliver [111]-oriented SCD substrates to the exact geometry required for the maser cavity’s H-field maximum.
  • Surface Engineering: NV centers require ultra-smooth, low-roughness surfaces to avoid dephasing. 6CCVD delivers Ra < 1 nm polish on SCD faces — directly matching the requirement for coherent spin ensembles.
  • Metalization: For hybrid integration with the metallic cavity or for bonding to a high-Q sapphire resonator mount, 6CCVD provides in-house metalization with Ti, Pt, Au, Pd, W, or Cu stacks via evaporation or sputtering.
  • Thickness Control: 6CCVD can produce SCD in the 0.1 µm - 500 µm range — ideal for thin diamond membranes where the cavity geometry demands a sub-millimeter sample.
  • Doping Profiles: Custom boron-doped or nitrogen-doped diamond (both SCD and PCD) is available for tailoring spin-resonance and conductivity properties.
  • In-House PhD Team: 6CCVD’s materials scientists can assist with NV-density optimization (N concentration, irradiation energy, annealing schedule) and crystal orientation selection for spin-photonic and quantum-microwave applications.
  • Material Selection Consultation: For experiments targeting higher-temperature maser operation (77 K, 50 K, or even room temperature), 6CCVD can advise on N-impurity concentrations, NV conversion efficiency, and isotopic purification (12C enrichment) to extend coherence times.
  • Cavity-Ready Diamond: 6CCVD can pre-shape and pre-polish diamond samples to integrate directly into the researcher’s existing microwave cavity, reducing in-house fabrication overhead.

For custom specifications, NV-center engineering, or material consultation for maser, quantum-sensing, or ultra-low-noise microwave oscillator projects, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

Solid-state masers are uniquely positioned to serve as ultra-low phase noise microwave sources due to their exceptionally low noise temperatures. However, their practical application has been historically limited by low output power and the need for deep cryogenic cooling. In this work, we present a novel design for a continuous-wave, diamond-based maser oscillator operating at ∼14.5 GHz and moderate cryogenic temperatures (∼180 K), achieving output power levels exceeding −30 dBm (1 μW). This performance represents a two-orders-of-magnitude improvement over previous diamond- or ruby-based maser oscillators. Our system integrates a high-Q (∼2460) compact metallic microwave cavity with optically pumped [111]-oriented NV-rich diamond crystals. The cavity supports efficient light coupling and thermal dissipation, enabling sustained high-power optical excitation (>1 W) using cost-effective green LEDs. We demonstrate stable maser operation with good spectral quality and validate its output through both frequency- and time-domain analysis with phase noise data when operated in “free-running” mode. In addition, we provide phase noise estimations based on Leeson’s model and show that, when coupled to a high-Q external resonator, such masers could approach thermally limited phase noise levels. These predictions suggest strong potential for diamond masers to outperform traditional ruby-based or similar maser systems, especially given their ability to operate at higher temperatures using rugged, He-free Stirling coolers. Despite current limitations related to frequency stability and jitter, this work establishes diamond-based masers as promising candidates for next-generation ultra-low phase noise microwave oscillators. Further engineering optimization—particularly in field stability, thermal regulation, and feedback locking—will be key to unlocking their full potential.

  1. 1964 - Microwave Solid-State Masers