Superconducting boron doped nanocrystalline diamond on boron nitride ceramics
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2019-01-01 |
| Journal | Nanoscale |
| Authors | Soumen Mandal, Henry A. Bland, Jerome A. Cuenca, Malcolm Snowball, Oliver A. Williams |
| Institutions | BioTransformations (United Kingdom), Cardiff University |
| Citations | 16 |
| Analysis | Full AI Review Included |
Executive Summary
Section titled “Executive Summary”- Superconducting diamond on ceramics achieved: Heavy boron-doped nanocrystalline diamond (BDD) was successfully grown on hexagonal boron nitride (h-BN) ceramic substrates via microwave plasma chemical vapor deposition (MPCVD), retaining superconducting properties with a transition temperature of approximately 3.4 K and a transition width of 1 K.
- Surface-charge-driven seeding strategy: The negative zeta (ζ) potential of the BN ceramic in the pH range of 6-7 dictated the selection of hydrogen-terminated, positively charged nanodiamond seeds for effective electrostatic seeding.
- Hygroscopic substrate challenge solved: A mandatory 120 °C pre-bake for 12 hours was required to eliminate absorbed moisture and prevent blister formation during initial plasma exposure — directly addressing the hygroscopic nature of the boric oxide binder.
- Dielectric property enhancement: The diamond-on-BN hybrid achieved a dielectric constant of 9.5 ± 0.3 with a loss tangent of 0.01 ± 0.002, compared to 3.9 ± 0.1 for the bare ceramic, attributed to Maxwell-Wagner-Sillars interfacial polarization.
- High-quality nanocrystalline film confirmed: Raman spectroscopy revealed a sharp diamond peak at 1332 cm-1 with no non-diamond carbon signatures in the undoped layer, confirming pinhole-free growth.
- Practical scalability validated: Dense, continuous 5 µm thick diamond layers were achieved via colloid-based seeding, demonstrating the potential for large-scale superconducting diamond-on-ceramic devices in electrochemistry and supercapacitor applications.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Substrate | h-BN ceramic (boric oxide binder) | — | 10 × 10 mm, 0.5 mm thickness |
| Substrate dielectric constant | 3.9 ± 0.1 | — | Bare BN ceramic at 1 kHz-1 MHz |
| Hybrid dielectric constant | 9.5 ± 0.3 | — | Diamond-on-BN composite |
| Loss tangent | 0.01 ± 0.002 | — | Diamond-on-BN composite |
| Diamond film thickness | ~5 | µm | Measured via SEM cross-section |
| Superconducting transition temperature (Tc) | ~3.4 | K | Heavy boron-doped nanocrystalline diamond |
| Transition width (ΔTc) | 1 | K | 99%-1% of normal state resistance |
| B/C ratio in gas mixture | 12,820 | ppm | Heavy doping regime |
| CH4 concentration | 3 | % | In H2/CH4/TMB mixture |
| TMB source concentration | 2000 | ppm | Premixed H2/TMB gas |
| Microwave power | 4 | kW | Seki Technotron AX6500 |
| Gas pressure | 50 | Torr | During diamond growth |
| Substrate temperature | ~800 | °C | Williamson dual-wavelength pyrometer |
| Initial plasma power | 1.5 | kW | Low-power ignition stage |
| Initial plasma pressure | 5 | Torr | Low-power ignition stage |
| Pre-bake temperature | 120 | °C | Hotplate dehydration step |
| Pre-bake duration | 12 | hours | Moisture expulsion from ceramic |
| ζ-potential of BN ceramic | Negative (IEP ≈ pH 2.6) | mV | Measured across pH 3-9 |
| Nanodiamond seed size | 5 | nm | Hydrogen-terminated colloid |
| Raman diamond peak | 1332 | cm-1 | Characteristic sp3 signature |
| BDD Fano shoulder (DF) | 1285 | cm-1 | Boron-induced redshift |
| BDD broad band (B peak) | 1220 | cm-1 | Locally distorted lattice |
| Excitation current (4-probe) | 5 | µA | van der Pauw configuration |
| Electrolyte (ζ-potential) | 10-3 M KCl | — | Streaming channel measurement |
Key Methodologies
Section titled “Key Methodologies”- Substrate preparation: 10 × 10 mm × 0.5 mm h-BN ceramic squares with boric oxide binder were pre-baked at 120 °C for 12 hours to expel absorbed moisture, then directly transferred to the reactor.
- Zeta potential characterization: Streaming potential was measured using a Surpass™ 3 electrokinetic analyser with 10-3 M KCl electrolyte; channel width held at 100 µm; pH varied across 3-9 using 0.1 M HCl/NaOH titrant.
- Seeding: Positively charged hydrogen-terminated 5 nm nanodiamond aqueous colloid applied via brief immersion (not agitation, to prevent ceramic dissociation); substrates then rinsed in DI water and blow-dried.
- Diamond growth (MPCVD): Seki Technotron AX6500 reactor at 4 kW microwave power, 50 Torr pressure, ~800 °C substrate temperature.
- Gas chemistry — undoped: H2 + CH4 (3% methane).
- Gas chemistry — boron-doped: H2 + CH4 (3%) + TMB (B/C = 12,820 ppm).
- Characterization stack: SEM (Hitachi SU8200, 20 kV), Raman (514 nm excitation, inVia Renishaw), dielectric measurement (Keysight 16451B + E4991A, 1 kHz-1 MHz), superconductivity (Quantum Design PPMS, 2-10 K, van der Pauw).
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”-
Applicable Materials:
- Heavy Boron-Doped Nanocrystalline PCD (BDD): Directly maps to the superconducting layer in this study. 6CCVD’s heavy doping capability (B/C ratios in the thousands of ppm) is well-suited for replicating Tc values near 3-4 K.
- Intrinsic Nanocrystalline PCD: For the undoped reference film demonstrating high Raman quality and pinhole-free coverage on non-diamond substrates.
- Substrate offerings: While the study used h-BN ceramics, 6CCVD can deposit BDD on alternative machinable dielectric substrates (Si, SiO2, AlN, Mo, WC-Co) with thicknesses from 0.1 µm to 500 µm for thin films and up to 10 mm for bulk substrates.
-
Customization Potential:
- Pre-bake/moisture-management protocols: Given the critical 120 °C / 12-hour pre-bake identified in the paper, 6CCVD can provide pre-conditioned substrates with verified moisture levels to streamline downstream MPCVD processing.
- Custom metalization: For four-point van der Pauw contacts used in superconducting measurements, 6CCVD offers in-house deposition of Ti, W, or Au contact pads — eliminating the need for silver paste and enabling permanent, low-resistance ohmic contacts to BDD.
- Laser cutting & dicing: 10 × 10 mm squares used here can be custom-diced from wafers up to 125 mm (PCD) to your required geometry with tight dimensional tolerances.
- Surface engineering: Ra < 5 nm polishing on polycrystalline surfaces ensures reliable ζ-potential measurements and uniform seeding density.
-
Engineering Support:
- The paper highlights a non-trivial challenge: matching seed surface charge to substrate ζ-potential to avoid blistering and sparse coverage. 6CCVD’s in-house PhD engineering team can advise on seeding protocols — including hydrogen- vs. oxygen-terminated nanodiamond colloids, agitation parameters, and pre-bake sequences — for your specific ceramic or non-diamond substrate.
- For electrochemistry, supercapacitor, or cryogenic device projects requiring BDD-on-ceramic or BDD-on-metal architectures, 6CCVD provides consultation on gas chemistry (CH4/TMB ratios), microwave power tuning, and substrate-fixture design to achieve superconducting or highly conductive diamond coatings.
-
Call to Action: For custom specifications, heavy doping consultation, or substrate-matched diamond seeding advice, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
In this work we have demonstrated the growth of nanocrystalline diamond on boron nitride ceramic. We measured the zeta potential of the ceramics to select the diamond seeds. Diamond was then grown on the seeded ceramics using a microwave chemical vapour deposition system. A clear difference was found between the samples which were seeded with nanodiamond and the ones not seeded before growth. Raman spectroscopy confirmed the excellent quality of the diamond film. Dielectric measurements showed an increase in the dielectric constant of the material after diamond growth. The diamond was also doped with boron to make it superconducting. The film had a transition temperature close to 3.4 K. Similar strategies can be applied for the growth of diamond on other types of ceramics.
Tech Support
Section titled “Tech Support”Original Source
Section titled “Original Source”References
Section titled “References”- 2002 - High Performance Non-Oxide Ceramics II, Structure and Bonding