Skip to content

Transitions in polycrystalline diamond probed by steady state, modulated and transient surface photovoltage spectroscopy

MetadataDetails
Publication Date2022-11-30
JournalSemiconductor Science and Technology
AuthorsThomas Dittrich, Steffen Fengler
InstitutionsHelmholtz-Zentrum Berlin für Materialien und Energie, Helmholtz-Zentrum Hereon
Citations7
AnalysisFull AI Review Included

Transitions in Polycrystalline Diamond Probed by Surface Photovoltage Spectroscopy

Section titled “Transitions in Polycrystalline Diamond Probed by Surface Photovoltage Spectroscopy”
  • Core Achievement: Highly sensitive Surface Photovoltage (SPV) spectroscopy across dc (Kelvin probe), ac (modulated), and ac (transient) regimes maps electronic transitions in polycrystalline CVD diamond spanning near-infrared to deep-ultraviolet (0.8-5.8 eV).
  • Defect Fingerprint Catalog: Eight distinct defect transitions (D1-D8) were detected at 0.8-0.9, 1.0, 1.37, 1.78, 2.27, 3.15, 4.2, and 5.42 eV, providing a reference dataset for grain-boundary disorder, sp2 bonded carbon, and dangling bond states.
  • Phonon-Assisted Bandgap Analysis: SPV resolved exciton-phonon replicas at Eg - Ex ± hνLA,LO (5.27 / 5.53 eV) and Eg - Ex + hνTO (5.60 eV) relative to diamond’s 5.47 eV indirect bandgap.
  • Asymmetry Discovery: Nucleation-side vs. growth-side illumination revealed opposite charging polarity, with grain-boundary density driving preferential electron separation.
  • Method Versatility: Demonstrated applicability to ultra-wide bandgap semiconductors beyond diamond (e.g., GaN, AlN, β-Ga2O3) for research and routine quality control.
  • Noise Floor Benchmark: Achieved noise levels as low as < 0.5 µV (ac modulated) and ~ 30 µV (dc Kelvin) — establishing SPV as a viable non-destructive metrology tool for wide-bandgap materials.
ParameterValueUnitContext
Sample TypePolycrystalline CVD diamond (Type II)—Window-grade, nucleation + growth sides characterized
Sample Thickness0.1mmCommercial freestanding CVD window
Sample Area1 × 1cm2Standard substrate geometry
Hydrogen Content< 1000ppmBelow detection of typical grain-boundary passivation
Silicon ContentBelow detection limitppmNominally undoped
Nitrogen ContentBelow detection limitppmNominally undoped
Indirect Bandgap (Eg)5.47eVReference [1]
Exciton Binding Energy (Ex)0.07eVReference [1]
LA/LO Phonon Energy (hνLA,LO)0.132eVReference [1]
D1 Transition Energy0.8-0.9eVsp2 π → π∗ / dangling bond onset
D2 Transition Energy1.0eVDominant feature, π → π∗ at grain boundaries
D3 Transition Energy1.37eVBroad energy distribution (multiple signatures)
D4 Transition Energy1.78-1.8eVBulk defect (substitutional nitrogen related)
D5 Transition Energy2.27eVπ → σ∗ in disordered phase
D6 Transition Energy3.15eVπ → σ∗ in disordered phase
D7 Transition Energy4.2-4.6eVValence to conduction band tails
D8 Transition Energy5.42eVNear-bandgap defect, origin unclear
Phonon Replica 15.27eVEg - Ex - hνLA,LO
Phonon Replica 25.53eVEg - Ex + hνLA,LO
Phonon Replica 35.60eVEg - Ex + hνTO
Noise Floor (dc Kelvin)~ 30µVFull spectrum < 30 min acquisition
Noise Floor (ac modulated)~ 3µVCharge amplifier configuration
Noise Floor (high-Z buffer)< 0.5µVSnO2:F coated electrode + mica spacer
Noise Floor (transient, short time)~ 500µVAt 20 ns time gate
Noise Floor (transient, long time)< 100µVAt times > 0.1 ms
Laser Repetition Rate0.25HzTransient SPV pulse rate
Averages per Data Point10—Transient measurement
  • Sample Selection: Polycrystalline CVD diamond window (0.1 mm thick, 1 × 1 cm2, Diamond Materials GmbH Type II, H < 1000 ppm).
  • Three SPV Regimes on Identical Electrode / Position:
    1. dc (Kelvin probe) — Contact potential difference (CPD) measured with vibrating steel bar electrode.
    2. ac (modulated) — Lock-in amplifier with in-phase (X) and 90° phase-shifted (Y) detection.
    3. ac (transient) — Pulsed laser excitation (0.25 Hz), 10 averages, logarithmic time readout.
  • Illumination Sources:
    • Xe lamp for broadband UV-vis-NIR coverage.
    • Halogen lamp for low-straylight NIR characterization.
    • Tunable OPO / dye-laser system for photon-energy-resolved scans from ~ 0.5 to ~ 5.8 eV.
  • Beam Conditioning: Motorized filter wheel for straylight suppression; beam expander with minimum zoom factor 2.5; cut-on filter (900 nm) for straylight-isolated measurements.
  • Electrode Geometries:
    • Perforated electrode + charge amplifier for dc/ac modulated regimes.
    • SnO2:F coated electrode + mica spacer + high-impedance buffer (× 10 gain) for ultra-low-noise NIR measurements.
  • Sample Orientation Protocol: Diamond flipped to compare nucleation-side vs. growth-side illumination under identical electrode positioning.
  • Phonon-Assisted Transition Identification: Compared observed spectral features against literature values for indirect exciton-phonon coupling at 5.268, 5.531, and 5.615 eV.
  • Derivative Spectroscopy: First-derivative of -ΔCPD spectra applied to enhance onset detection for closely spaced transitions.
  • Applicable Materials:

    • The defect spectroscopy catalog in this work (D1-D8) requires CVD polycrystalline diamond with well-characterized nucleation and growth surfaces — 6CCVD Optical Grade PCD (polished to Ra < 5 nm on inch-size wafers) is ideally suited as a baseline substrate.
    • For experiments probing the role of acceptor density near 1 eV, 6CCVD Heavy Boron-Doped PCD (BDD) enables controlled activation-energy tuning matching the dose-dependent shifts described in [21].
    • For bandgap-edge phonon-assisted studies, 6CCVD High-Purity SCD (0.1-500 µm thickness) provides the crystalline baseline referenced in [30], where transient SPV signals were “up to about ten times larger” than on PCD.
  • Customization Potential:

    • The 0.1 mm × 1 × 1 cm2 geometry used here is a standard reference, but SPV electrode contact geometry is application-specific. 6CCVD offers custom metalization (Ti / Pt / Au / Pd / W / Cu) and laser cutting to produce tailored electrode pad patterns and die dimensions without the need for customers to invest in post-processing metallization equipment.
    • For straylight-sensitive NIR measurements, an SnO2:F transparent electrode is advantageous — 6CCVD can support TCO-compatible surface engineering on request.
  • Engineering Support:

    • The paper demonstrates that measurement regime (dc vs. ac modulated vs. ac transient) dramatically alters observed sign and magnitude of defect-related SPV signals — a critical consideration for any group designing wide-bandgap semiconductor characterization workflows. 6CCVD’s in-house PhD team can assist with material selection for projects targeting photovoltaic, photocatalytic, bio-sensor, or power-electronics applications of polycrystalline and single-crystal diamond.
    • 6CCVD substrates are available up to 125 mm diameter (PCD) and 10 mm thickness, with SCD / PCD / BDD variants covering the full parameter space required to extend this defect-state mapping from the bandgap into the device-relevant sub-bandgap regime.
  • Call to Action:

    • For custom specifications, metalization stack design, or material consultation on wide-bandgap diamond characterization, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract

Abstract Numerous electronic transitions in polycrystalline chemical vapor deposition diamond with characteristic nucleation and growth sides were obtained by highly sensitive surface photovoltage (SPV) spectroscopy in dc (Kelvin probe), ac (modulated) and ac (transient) regimes from near infrared to deep ultraviolet. In the dc regime, defect transitions D1 to D8 were detected at 0.8-0.9, 1, 1.37, 1.78, 2.27, 3.15, 4.2 and 5.42 eV, respectively. Hints for more transitions were found for measurements in the ac (modulated) regime in the range near D3. SPV measurements in the ac (transient) regime showed the importance of disorder for relaxation of SPV signals excited at different photon energies. Phonon assisted transitions were observed at E g − E x − hν LA,LO , E g − E x + hν LA,LO and E g − E x + hν TO . The developed SPV techniques are suitable for applications in research and quality control not only for diamond but also for any other semiconductor with ultra-wide bandgap.