Skip to content

Microfabrication techniques and device applications of single crystalline diamond

MetadataDetails
Publication Date2025-11-19
JournalFunctional Diamond
AuthorsTiqing Zhao, Wenjun Liang, Pak San Yip, Anliang Lu, Yang Lü
InstitutionsChinese University of Hong Kong, University of Hong Kong
Citations3
AnalysisFull AI Review Included

Microfabrication Techniques and Device Applications of Single Crystalline Diamond: Technical Analysis

Section titled “Microfabrication Techniques and Device Applications of Single Crystalline Diamond: Technical Analysis”
  • Comprehensive Fabrication Roadmap: A systematic review covering growth (HPHT/CVD), 2D patterning (ICP-RIE/FIB), and 3D structuring (IAL, DOI, angled etching) of single crystalline diamond (SCD) for MEMS applications.
  • Extreme Material Performance: Documented thermal conductivity reaching 24 W·cm-1·K-1 at room temperature and 285 W·cm-1·K-1 near 63 K, positioning SCD as a premier thermal management substrate.
  • Quantum-Grade Precision: Demonstrated nanoneedles with 1-3 atomic step surface quality via FIB + plasma refining; nanorods achieving 200 nm diameter with aspect ratios up to 10.
  • Heterojunction Innovation: MoS2/diamond and ZnO/diamond heterojunctions exhibiting rectification behavior from 25°C to 290°C, addressing n-type doping limitations.
  • Resonant Sensor Breakthrough: Single-crystal diamond cantilevers integrated with FeGa thin film achieving magnetic field sensitivity of 4.83 Hz/mT and minimum detectable force of 2.14 × 10-12 N.
  • Ultra-High Q Factors: Diamond MEMS resonators achieving Q > 106 through defect and strain engineering, surpassing traditional semiconductor limits.
  • Current Limitations Identified: High interfacial thermal resistance in GaN/diamond stacks, inefficient n-type doping, and scalability challenges in multi-dimensional fabrication.

ParameterValueUnitContext
Thermal conductivity (RT)24W·cm-1·K-1High-purity SCD, both HPHT and CVD sources
Thermal conductivity (63 K)285W·cm-1·K-1Peak value for high-purity synthetic SCD
Strain-induced κ enhancement~15%Predicted under small-scale uniaxial strain
Nanorod diameter200nmICP-RIE with pure O2, 700 W ICP power
Nanorod aspect ratio10:1Height 2 µm / diameter 200 nm
ICP-RIE etch rate (Ar/O2)260nm/minVertical sidewalls, 200 nm diameter nanorods
Nanoneedle height550-600nmAr/He/N2 microwave plasma etching
Nanorod array diameter range100-500nmEBL + O2 plasma for neuronal growth studies
Nanorod spacing1-10µmLarge-area array patterning
FIB acceleration voltage30kVRough milling at 700 pA, fine at 20-40 pA
FIB bridge width~100nmIn-situ TEM tension test specimens
Surface quality post-FIB1-3atomic stepsPlasma refining after FIB rough machining
Graphene breakdown current density1.7 × 109A/cm2Ti/Au contacts on diamond substrate
Graphene current density (general)>109A/cm2Ohmic and tunnel contacts on diamond
Magnetic field sensitivity4.83Hz/mTFeGa/SCD cantilever ΔE effect
Minimum detectable force2.14 × 10-12NFeGa/Ti/SCD all-electric detection
Quality factor (Q)>106—Diamond MEMS resonators via defect/strain engineering
Boron-doped Hall mobility (RT)2200cm2/(V·s)Lightly boron-doped CVD diamond
Phosphorus donor level~0.6eVShallow donor below conduction band
Heterojunction test temperature range25-290°Cn-WO3/p-diamond rectification testing
MoS2 film thermal stability limit550KComplete detachment from diamond substrate
Best rectification ratio temperature120°Cn-MoS2/p-BDD heterojunction
2-inch heteroepitaxial diamond2inch(001) diamond on (11-20) sapphire substrate
Diamond membrane thickness (typical)Ultrathin / sub-µmµmIAL, laser slicing, DOI techniques

  • SCD Growth Methods:
    • HPHT (Bundy et al., 1955) — bulk crystal synthesis
    • Microwave Plasma CVD (Kamo et al., 1983) — homoepitaxial and heteroepitaxial growth on Ir/SrTiO3 or sapphire substrates
    • Heteroepitaxial (001) diamond on (11-20) sapphire via step-flow mode (Kim et al., 2020; Takaya et al., 2021)
  • Thin-Film Lift-Off Techniques:
    • Ion Implantation-Assisted Lift-Off (IAL) with electrochemical etching
    • Diamond-on-Insulator (DOI) with SiO2 sacrificial bonding
    • Laser slicing at {100} plane with controlled crack propagation
    • Femtosecond laser ablation for microarray tool fabrication
  • 2D Nanostructure Fabrication:
    • Pure O2 ICP-RIE: 700 W ICP power, high-aspect-ratio nanorods (aspect ratio 10)
    • Ar/O2 ICP-RIE: 50 sccm each, 260 nm/min etch rate
    • Ar/Cl2 ICP-RIE: Low photoresist selectivity, superior surface quality for micro-lenses/grooves
    • Ar/He/N2 microwave plasma: Nanoneedle shape control via gas composition, pressure, bias
    • FIB milling: 30 kV, 700 pA rough → 20-40 pA fine → plasma refining for atomic-step finish
  • 3D Structure Fabrication:
    • IAL: Ion implantation creates sacrificial graphitic layer → electrochemical etch release
    • DOI: SiO2 bonding with KOH or HF release
    • Faraday Cage Angled Etching: Grid defines equipotential dark space for controlled ion angle
    • Tilted Sample Stage Etching: Direct angular plasma exposure for cantilevers and nanobeams
  • Doping Strategies:
    • p-type: In-situ CVD boron doping (BCl3 source) or multi-dose ion implantation
    • n-type: Phosphorus epitaxial growth on (111) diamond (~0.6 eV donor level)
    • Heterojunction n-type pairing: ZnO nanorods, WO3 nanorods, MoS2 nanosheets on p-diamond

The microfabrication techniques and device architectures described in this review demand high-purity, precisely engineered diamond substrates. Below is how 6CCVD’s manufacturing capabilities align with the specific requirements identified in this work.

Application DomainRecommended 6CCVD MaterialRationale
Thermal management (GaN/SiC/diamond HEMTs)Optical Grade SCD substrates (up to 10 mm thickness)High thermal conductivity (24 W·cm-1·K-1) requires low-nitrogen, low-dislocation single-crystal material
NV-center quantum sensingHigh-purity SCD membranes (0.1-10 µm)Low nitrogen background enables long spin coherence times
MEMS cantilevers / nanomechanical resonatorsSCD plates with Ra < 1 nm polishAtomically smooth surfaces essential for Q > 106 resonators and FIB-defined nanostructures
Heterojunction devices (MoS2, ZnO, WO3 on diamond)Boron-Doped (BDD) single-crystal substratesControlled p-type conductivity for rectification characterization; BDD available in custom doping concentrations
Diamond-on-Insulator (DOI) bondingSCD with one-side or double-side polishDOI fabrication requires defect-free bonding surfaces
Photonic crystal cavities / nanophotonic circuitsUltrathin SCD membranes (sub-µm to µm range)Telecommunication-wavelength photonic crystals require precise thickness control
  • Custom Dimensions: This review references free-standing membranes, 2-inch heteroepitaxial wafers, and micro-bridge structures. 6CCVD supplies SCD and PCD plates/wafers up to 125 mm with thicknesses from 0.1 µm to 500 µm for SCD, and substrates up to 10 mm for bulk applications.
  • Custom Metalization: Multiple devices in this paper rely on Ti/Au ohmic contacts (e.g., graphene/diamond spin valves) and FeGa/Ti/SCD multilayer stacks for magnetic sensing. 6CCVD offers in-house metalization with Au, Pt, Pd, Ti, W, and Cu. Custom multilayer stacks (Ti/Pt/Au, Ti/W/Au) are available to match specific Schottky or ohmic contact requirements.
  • Laser Cutting & Dicing: The review discusses laser slicing at {100} planes and femtosecond laser ablation for microarray tools. 6CCVD provides laser cutting and dicing services for custom chip geometries, enabling researchers to receive pre-patterned or pre-diced diamond ready for ICP-RIE or FIB processing.
  • Surface Engineering: For DOI bonding and IAL processing, 6CCVD delivers both single-side and double-side polished substrates with Ra < 1 nm (SCD) to meet the stringent flatness requirements of wafer bonding protocols.

6CCVD’s in-house PhD engineering team provides consultation on:

  • Material selection for diamond MEMS, quantum, thermal management, and heterojunction device projects.
  • Growth method matching — recommending HPHT vs. CVD homoepitaxial SCD based on defect density, nitrogen concentration, and isotopic purity requirements.
  • Fabrication pathway planning — advising on compatible polishing grades, metalization schemes, and thickness specifications for downstream ICP-RIE, FIB milling, IAL, or DOI processing.
  • Application-specific doping — boron concentration guidance for BDD electrodes, p-type heterojunction partners, or electrochemical sensing substrates.

For custom specifications, material consultation, or to discuss your diamond MEMS, quantum device, or thermal management project requirements, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

Diamond has many excellent physicochemical properties including ultrahigh hardness, wide bandgap, outstanding thermal conductivity, and high electron mobility, which has emerged as a critical material for high-power electronics, quantum technologies, and micro/nano-electromechanical systems (MEMS/NEMS). Single crystalline diamond tends to have better performance than polycrystalline diamond in some fields including thermal management, optics and quantum information. However, its extreme hardness and chemical inertness pose significant challenges for scalable microfabrication and require specialized techniques beyond conventional silicon-based processes. This paper systematically summarizes the latest progress in single crystalline diamond (SCD) MEMS manufacturing, including the diamond growth achieved through high pressure and high temperature (HPHT) or chemical vapor deposition (CVD), two-dimensional (2D) nanostructures achieved through inductively coupled plasma (ICP) etching and focused ion beam (FIB) milling and three-dimensional (3D) structures achieved through ion implant-assisted exfoliation (IAL), diamond on insulator (DOI), and angled etching strategies. We focused on introducing the applications of SCD in thermal management, photonic device, quantum systems, and heterojunctions. However, there are still some challenges, such as high fabrication costs, interfacial thermal resistance in hetero-integrated devices, and limitations in n-type doping efficiency. Emerging approaches like deep elastic strain engineering (DESE) can offer novel pathways to regulate SCD’s electronic and quantum properties. In the future, interdisciplinary combination in materials science, nanofabrication, and quantum engineering are critical to for next-generation electronics, quantum information, and MEMS technologies of diamond.