Influence of Dressing Methods on Chipping Size During Si and SiC Die Singulation - A Review
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2025-12-09 |
| Journal | Journal of Manufacturing and Materials Processing |
| Authors | Sergey N. Grigoriev, Anna A. Okunkova, М. A. Volosova, Khaled Hamdy, Alexander Metel |
| Institutions | Nahda University, Lomonosov Moscow State University |
| Analysis | Full AI Review Included |
Influence of Dressing Methods on Chipping Size During Si and SiC Die Singulation: Technical Review
Section titled “Influence of Dressing Methods on Chipping Size During Si and SiC Die Singulation: Technical Review”Executive Summary
Section titled “Executive Summary”- Process Focus: Systematic review of PCD saw blade dressing methods aimed at reducing chipping during dicing of hard-brittle Si and SiC wafers for IC singulation.
- Material Challenge Addressed: Both Si and SiC exhibit low fracture toughness, high hardness, and high thermal conductivity, making die-edge quality highly sensitive to blade wear and grit exposure.
- Three Dressing Categories Analyzed: Mechanical dressing (board/wheel), Electrical Discharge Truing/Grinding (EDT/EDG), and combined Dressing-Coating-Redressing.
- Best Result - Electrical Discharge Truing: Tungsten-copper electrode produced 0 µm chipping over 20 m dicing distance on 4H-SiC wafers.
- Best Mechanical Result: SiC board dresser (grit > 3500) reduced Si-wafer chipping by 55% versus Si-wafer dressing baseline.
- Combined Method Outcome: Metallic glass coating + redressing achieved 23-36% chipping reduction — less effective than standalone EDT or optimized mechanical dressing.
- Critical Insight: Grit protrusion height of ~20% of average diamond grain size is optimal for segment sawing performance.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Wafer diameter | ~300 | mm | Standard Si/SiC production wafer |
| Die street width | 60 - 80 | µm | Typical IC singulation lane |
| Two-wheel Z1 width | 27 - 32 | µm | Preliminary dicing blade |
| Two-wheel Z2 width | 25 - 30 | µm | Final dicing blade |
| Acceptable back-side chipping (bare die) | < 70 | µm | Auto-vision reject threshold >10% |
| Improved chipping after optimization | < 15 | µm | Combined mechanical adjustment |
| PCD saw blade grit (sample) | 40/45 (355 - 425) | µm | Iron/Cu/Sn/Co/Ni-bonded PCD |
| Discharge channel temperature | ~10,000 | K | EDM plasma sublimation regime |
| Interelectrode gap | 0.050 - 0.075 | mm | Conductive materials |
| Electrode wheel linear speed | 3.3 - 5.0 | mm/s | EDT optimal range |
| Electrode wheel rotation | 1,000 - 6,000 | rpm | EDT optimal range |
| EDT discharge current | 1 | A | Recommended |
| EDT circuit voltage | 100 | V | Recommended |
| EDT discharge duration | 0.4 | µs | Recommended |
| Circular run-out (ø125 mm blade) | < 0.050 | mm | Post-EDG quality |
| Bond material removal (per dress) | 0.05 - 0.15 | mm | Rake and flank faces |
| Cutting-edge radius (max) | 0.1 - 0.2 | mm | Dress monitoring limit |
| Mechanical dresser grit (recommended) | > 3,500 | mesh | SiC board preferred over Si wafer |
| Mechanical feed rate | 10 - 50 | mm/s | Dressing pass range |
| Mechanical rotation speed | 15 - 50 | min-1 | Dressing spindle |
| Dress passes | 20 - 70 | lines | Total dressing cycles |
| EDT surface roughness Rz | ~1 | µm | With oil-based dielectric |
| Grit protrusion optimum | ~20% of grain size | — | Optimal sawing regime |
| Chip-free dicing distance (4H-SiC, EDT) | 20 | m | Tungsten-copper electrode |
| Chipping without dressing (SiC) | 20 - 30 | µm | Reference baseline |
Key Methodologies
Section titled “Key Methodologies”- Wafer Pre-Processing — Laminate Si/SiC wafer on Mylar tape; pre-cut grooves to full wafer thickness using PCD saw blade.
- Back-Side Grinding — Invert wafer, grind backside to target thickness; apply chemical-mechanical polishing (CMP) plus dry polishing for stress relief.
- Mechanical Board Dressing (PCD Blade) — Rough dress with coarse diamond wheel → semi-finish → finish; use SiC board dresser with grit > 3500 and water-based coolant covering full contact area.
- Electrical Discharge Truing/Grinding (EDT/EDG) — Dress PCD blade with W-Cu or Cu disk electrode; maintain interelectrode gap of 0.050-0.075 mm; rotate electrode wheel at 1,000-6,000 rpm under oil-based dielectric.
- Combined Dressing-Coating-Redressing — Initial mechanical dress, deposit Zr-based or metallic-glass coating via sputtering/beam-assisted deposition, then redress to expose coated grit.
- Dicing Parameters — Use DISCO-type automatic dicing saw with vision alignment; align cut direction with crystallographic orientation of wafer; control spindle power and feed rate within the technological window.
- Quality Verification — Optical microscopy and SEM of die streets; measure chipping width, area, and frequency per 10 cut lines; monitor circular run-out and cutting-edge radius.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”-
Applicable Materials:
- Polycrystalline Diamond (PCD) Plates/Wafers — Sintered PCD with metal-bond matrices (Fe, Co, Ni, Cu, Sn-based) directly correspond to the bond systems analyzed in the review. 6CCVD supplies custom-bonded PCD in diameters up to 125 mm, with thicknesses from 0.1 µm to 500 µm, and substrates up to 10 mm for structural support.
- Optical-Grade Single Crystal Diamond (SCD) — Recommended for researchers building next-generation dicing blades where sub-surface integrity and thermal conductivity are critical; available with Ra < 1 nm surface finish.
- Heavy Boron-Doped PCD (BDD) — When the application requires the conductive PCD variants referenced in EDT (electrical discharge truing requires conductive workpiece behavior).
-
Customization Potential:
- Grit Size Engineering: The review emphasizes grit size > 3500 and protrusion heights of ~20% grain size. 6CCVD can tailor PCD microstructure and grain distribution for these exact specifications.
- Custom Metalization: For researchers exploring the combined Dressing-Coating-Redressing technique (Zr-coating, metallic-glass coating), 6CCVD offers in-house metalization (Ti, W, Cu, Pt, Pd, Au) to pre-coat PCD saw blade edges or prepare coupons for sputter-target development.
- Precision Laser Cutting: Custom blade geometry, edge preparation, and prototype segments can be machined to the required < 0.050 mm run-out tolerance using 6CCVD’s precision cutting capabilities.
- Bond Composition Control: Custom Co, Ni, Fe, Cu, or W-bonded PCD variants to match the EDM electrode compatibility tables in the review.
-
Engineering Support:
- 6CCVD’s in-house PhD engineering team can assist with material selection for PCD saw blade R&D, helping clients match bond conductivity, grain size, and thermal resistance to specific EDT or mechanical dressing regimes.
- For die-singulation tooling projects, 6CCVD provides consultation on crystallographic orientation effects, blade wear characterization, and integration of CVD diamond coatings onto conventional saw bodies.
- Application-specific support for Si, 4H-SiC, 6H-SiC, and emerging wide-bandgap wafer dicing.
-
Call to Action: For custom specifications, bond-composition engineering, or material consultation on PCD saw blade development, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
The review is intended to systematize the latest achievements and the most promising methods in polycrystalline diamond saw blade dressing used for dicing Si and SiC wafers. Dicing, or die singulation, is important in IC assembly, and the quality of the die edges influences the final product quality. Reducing chipping size and width has been a scientific problem over the last few decades. Many techniques were proposed to solve it. The most practical solutions involved optimizing processing factors and cutting direction in accordance with the crystallographic structure of the wafers, since silicon and silicon carbide are hard and brittle materials with low fracture toughness, high hardness, and high thermal conductivity. Wear of the PCD saw blade is also a contributing factor to the formation of chipping and cracks. Dressing allows the bond material removal and diamond grain liberation, where grit size plays a critical role. Dressing techniques were divided into two groups depending on the nature of the exposure, and a combined technique of dressing-coating-redressing was also observed. The less significant chipping size effect was observed for the combined technique in dicing Si wafers when the effect of the techniques based on the mechanical and electrophysical exposures was more significant.
Tech Support
Section titled “Tech Support”Original Source
Section titled “Original Source”References
Section titled “References”- 2018 - Optimizing the dicing saw parameters of 60 μm wafer dicing street [Crossref]
- 2024 - Theoretical and experimental investigation of ultrasonic cutting kinematics and its effect on chip formation and surface generation in high-frequency ultrasonic vibration-assisted diamond cutting [Crossref]