Skip to content

Experimental demonstration and transformation mechanism of quenchable two-dimensional diamond

MetadataDetails
Publication Date2026-01-08
JournalNature Communications
AuthorsJiayin Li, Guoshuai Du, Lili Zhao, Wuxiao Han, Jiaxin Ming
InstitutionsZhuhai Institute of Advanced Technology, State Key Laboratory of Explosion Science and Safety Protection
Citations2
AnalysisFull AI Review Included
  • Breakthrough in 2D Diamond Synthesis: Successful fabrication of quenchable two-dimensional (2D) diamond via laser-heated diamond anvil cell (DAC) processing of few-layer graphene (FLG), achieving controlled thicknesses from bilayer to several hundred nanometers.
  • High-Pressure High-Temperature (HPHT) Recipe: Optimized synthesis at 20.0-32.3 GPa and ~1435-2924 K on polished Re foil substrates (10 µm thick, 3.9 nm roughness), using KBr/NaCl as pressure-transmitting media.
  • Superior Crystalline Quality: Quenched 2D diamond exhibits a narrow T2g Raman peak with FWHM of ~3.6 cm-1, comparable to commercial bulk diamond (3.3 cm-1).
  • Active Color Center Integration: Demonstrated strong photoluminescence from silicon-vacancy (SiV-, ZPL ~738 nm, linewidth ~6.1 nm) and nitrogen-vacancy (NV0, ZPL ~575 nm) centers without intentional doping.
  • Tunable Optoelectronic Properties: Optical bandgap tunable from 1.4 to 1.9 eV via control of sp3 concentration (71.3%-89.9%), confirmed by EELS analysis of the carbon K-edge.
  • Exceptional Thermal Stability: High sp3-content samples remain stable up to 1000 °C in argon, outperforming DLC, DLN, nano-diamond, and CVD diamond; lower sp3 samples graphitize at ~900 °C.
  • Mechanism Elucidation: HRTEM/SAED confirmed intermediate rhombohedral graphite (RG) mediates the hexagonal graphite (HG) → cubic diamond (CD) transition following (002)HG∥(003)RG∥(111)CD crystallographic relations.

ParameterValueUnitContext
Pressure Range20.0-32.3GPaHPHT synthesis window in DAC
Temperature Range~1435-2924KLaser-heated conditions
Raman T2g FWHM~3.6cm-1Quenched 2D diamond, 20.0 GPa / 1435 K
Commercial Diamond FWHM (ref.)~3.3cm-1Benchmark for crystalline quality
SiV- ZPL Wavelength~738nmPhotoluminescence peak
SiV- Linewidth~6.1nmPL spectral width
NV0 ZPL Wavelength~575nmPhotoluminescence peak
sp3 Concentration Range71.3-89.9%Determined via EELS σ*/π* ratio
Optical Bandgap Range1.4-1.9eVTauc plot analysis
2D Diamond Thickness (from 3L)~1.0nmHRTEM cross-section (9 Å theoretical for 3L diamane)
Re Substrate Thickness~10µmPolished foil absorber
Re Surface Roughness~3.9nmPolishing quality
Re Melting Point3450K@ 1 atm thermal ceiling
Sample Chamber Diameter~100µmDrilled gasket hole
Anvil Culet~300µmDAC geometry
Surface Roughness (Recovered Film)~2.2nmRecovered from 20.0 GPa / 1435 K
Graphite G Peak Position (HPRT)1587cm-1E2g mode
Graphite 2D Peak Position (HPRT)2774cm-1Second-order scattering
D Band Position1386cm-1Defect-activated mode
Carbon K-edge σ* Peak292.5eVsp3 bonding signature
Carbon K-edge π* Peak283.2eVsp2 bonding signature
Maximum Thermal Stability1000°CArgon atmosphere, 1 hr anneal
Graphitization Onset (low sp3)~900°CIDia/IG collapse threshold
HD (100) Interplanar Spacing~2.19-2.23ÅHexagonal diamond lattice
CD (111) Interplanar Spacing~2.11-2.12ÅCubic diamond lattice
RG (003) Interplanar Spacing~3.29ÅRhombohedral graphite
RG (101) Interplanar Spacing~2.14ÅRhombohedral graphite
HG Interlayer Distance~3.35ÅHexagonal graphite
HG-RG-CD Interfacial Angle~78°Orientation relationship
TEM Slice Thickness (FIB)60-70nmFEI Helios NanoLab 600i prep
TEM Acceleration Voltage300kVFEI Titan Cube 80-300
Raman Grating (2D diamond)1800grooves/mmSpectral resolution
PL Grating150grooves/mmColor center detection
Cryostat Minimum Temperature~77KLiquid N2 capability

  • Graphene Precursor Preparation: Mechanical exfoliation of few-layer graphene (FLG) using PDMS; layer number verified by Raman spectroscopy + atomic force microscopy.
  • Substrate Fabrication: Re foil polished to ~10 µm thickness with ~3.9 nm surface roughness; shaped via laser drilling into small chips acting as both substrate and laser absorber.
  • Sample Loading: Graphene transferred onto Re chip; sealed in DAC sample chamber (~100 µm diameter) drilled into pre-indented T301 stainless steel or Re gasket.
  • Pressure Calibration: Ruby R1 fluorescence red shift used for in-situ pressure measurement.
  • HPHT Treatment: Double-sided laser-heated DAC with two tunable NIR lasers; temperature determined by Planck-fitting of acquired black-body radiation; system calibrated against quartz tungsten halogen standard lamp (50 W, Newport).
  • Pressure-Transmitting Medium (PTM): NaCl or KBr serving as both PTM and thermal insulator.
  • Quenching Protocol: Rapid decompression from peak HPHT to ambient; hydrophilic PTM removed by deionized water.
  • Sample Transfer: Recovered 2D diamond transferred onto fused silica (optical measurement) or TEM grids (microstructural analysis).
  • HRTEM Sample Prep: Pre-coated with Pt protective layer; FIB-milled (FEI Helios NanoLab 600i) into 60-70 nm ultrathin slices.
  • Spectroscopy: Raman/PL on Horiba iHR550 with 405 nm excitation (~1 µm spot, 100× objective); EELS collected on carbon K-edge; absorption via halogen tungsten lamp source.
  • Thermal Stability Test: Argon-atmosphere tube furnace annealing (200-1000 °C, 1 hr increments) followed by Raman mapping.

Research Requirement6CCVD Offering
Ultra-thin SCD films (nm-µm scale)SCD thickness range 0.1 µm - 500 µm; optical-grade single crystal diamond for ultra-thin exfoliation/free-standing film research
Bulk diamond substrate for comparisonPolished SCD substrates up to 10 mm thickness; Ra < 1 nm surface finish as direct FWHM benchmark reference
Active color center host (SiV-, NV0)SCD and BDD materials with controlled N/Si incorporation; custom doping consultation for quantum-grade samples
Tunable sp3 thin filmsOptical Grade SCD and Heavy Boron Doped PCD for sp3 baseline standards and optoelectronic substrates
Custom substrate dimensions for FLG transferCustom dimensions up to 125 mm (PCD) wafers; laser cutting service for non-standard geometries
Metalized Re-grade absorber analogCustom metalization (Au, Pt, Pd, Ti, W, Cu) for absorber/electrode integration
HRTEM cross-section referenceSub-µm polishing (Ra < 5 nm for inch-size PCD) for FIB-compatible substrates
Wafer-scale uniformity for device fabricationUp to 125 mm PCD plates; global DDU/DDP shipping
  • Applicable Materials: For replicating or extending this 2D diamond synthesis and benchmarking protocol, Optical Grade SCD is ideal as a high-quality bulk diamond reference (Ra < 1 nm, FWHM ~3.3 cm-1). For optoelectronic device integration leveraging the demonstrated 1.4-1.9 eV tunable bandgap, Boron-Doped Diamond (BDD) offers engineerable conductivity while preserving sp3 integrity.
  • Customization Potential: The paper relies on precision-polished Re foil substrates with ~3.9 nm roughness — a specification 6CCVD routinely achieves and surpasses on diamond substrates via in-house polishing capabilities. Should follow-up studies require patterned electrodes on diamond substrates, 6CCVD provides internal metalization with Au, Pt, Pd, Ti, W, and Cu, plus laser cutting for custom geometries.
  • Engineering Support: Our in-house PhD team can advise on material selection for quantum sensing platforms exploiting SiV-/NV0 centers, ultrathin diamond film delamination, and thermal stability studies at elevated temperatures (>1000 °C). 6CCVD supports research programs in carbon allotrope synthesis, phase transition mechanism studies, and extreme-condition (HPHT) device prototyping.
  • Call to Action: For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract

Two-dimensional (2D) diamond has aroused remarkable interest in nanoelectronics and optoelectronics, owing to its superior properties and flexible characteristics compared to bulk diamond. Despite significant efforts, great challenges lie in the experimental synthesis and transformation conditions of 2D diamond. Herein, we have demonstrated the experimental preparation of high quality 2D diamond with controlled thickness and distinguished properties, realized by laser-heating few-layer graphene in a diamond anvil cell. The quenched 2D diamond exhibited a narrow T2g Raman peak (linewidth ~3.6 cm−1) and intense photoluminescence of SiV- (linewidth ~6.1 nm) and NV0 centers. In terms of transformation mechanism, atomic structures of hybrid phase interfaces suggested that the intermediate rhombohedral phase subtly mediate hexagonal graphite to cubic diamond transition. Furthermore, the tunable optical bandgap and thermal stability of 2D diamond sensitively depend on its sp3 concentration. We believe our results can shed light on the structural design and preparation of many carbon allotropes and further uncover the underlying transition mechanism. 2D diamond is expected to show superior properties compared to bulk diamond, but its synthesis remains challenging. Here, the authors report a high-temperature high-pressure method to fabricate thermally stable 2D diamond via laser-heating of few-layer graphene in a diamond anvil cell, providing relevant insights into the 2D graphene-diamond transformation mechanisms.