Emerging Advanced Electronic Packaging Materials for Thermal Management in Power Electronics
Paper details
Section titled “Paper details”| Field | Value |
|---|---|
| Journal | Advanced Science |
| Published | 2026-02-16 |
| Authors | Yongjun Huo, Jiaqi Song, Wenqian Li, J. Y. Zhang, Yujin Zhang |
| DOI | 10.1002/advs.202524348 |
| Citations | 13 |
Power-module heat flow depends on two material systems: ceramic substrates and thermal interface materials. The review reports diamond’s intrinsic thermal conductivity at about 2300 W·m⁻¹·K⁻¹ and a diamond/Si₃N₄/GaN thermal boundary resistance of 3.1 ± 0.7 m²·K·GW⁻¹. These results show why interface quality can dominate package performance even when constituent materials conduct heat well. The numerical results come from cited experimental and modeling studies.
Two material systems define heat flow
Section titled “Two material systems define heat flow”Substrates sit between the semiconductor die and heat sink, carrying mechanical loads while providing electrical insulation. Thermal interface materials fill microscopic gaps and lower contact resistance between dissimilar layers.
Organic laminates have thermal conductivity below 1 W·m⁻¹·K⁻¹, while copper reaches 380 to 400 W·m⁻¹·K⁻¹ and aluminum reaches 237 W·m⁻¹·K⁻¹. Both metals lack electrical insulation and have expansion mismatches with wide-bandgap devices and metallization layers. Substrate selection therefore couples heat transport, dielectric strength, strength, expansion matching, and power-cycling reliability.
| Material | Thermal conductivity, W·m⁻¹·K⁻¹ | Bending strength, MPa | Thermal expansion, 10⁻⁶·K⁻¹ | Dielectric strength, kV·mm⁻¹ |
|---|---|---|---|---|
| Al₂O₃ | 14 to 37 | 200 to 470 | 6.5 to 7.2 | 12.3 |
| AlN | 159 to 219 | 267 to 484 | 2.7 to 4.6 | 43.6 |
| Si₃N₄ | 60 to 177 | 519 to 912 | 2.3 to 3.2 | 57.9 |
Al₂O₃ offers mature processing, but its thermal conductivity becomes restrictive as heat flux rises. AlN conducts heat well, but brittleness and thermal-shock performance remain concerns. Si₃N₄ combines higher bending strength, lower expansion, and better thermal-shock resistance. Peak conductivity therefore does not determine the practical choice.
Silicon nitride processing controls conductivity
Section titled “Silicon nitride processing controls conductivity”The review centers on Si₃N₄ because lattice oxygen, β-grain size, and grain-boundary phase govern phonon transport. High-purity α-Si₃N₄ powder with low surface oxidation and narrow particle-size distribution supports dense, low-defect ceramics. β-Si₃N₄ seeds promote α-to-β transformation and anisotropic grain growth.
One seed route used 0.5 wt.% Y₂O₃ at 1800 °C under 35 kPa nitrogen. Hot gas extraction was used to measure lattice oxygen, confirming that dissolved oxygen governs conductivity. Gas-pressure sintering reaches about 120 W·m⁻¹·K⁻¹, while optimized sintered reaction-bonded silicon nitride exceeds 140 W·m⁻¹·K⁻¹.
A 2024 gas-pressure-sintered formulation with Y₂Si₄N₆C and MgSiN₂ reached 116.7 W·m⁻¹·K⁻¹. It also reached 767 ± 29.6 MPa bending strength and 10.7 ± 0.4 MPa·m^1/2 fracture toughness.
Non-oxide additives can crystallize boundary phases, but additive quantity also controls liquid-phase viscosity and grain growth. Submicrometric closed pores can sever heat paths even when the bulk composition is correct. Rod-shaped β grains conduct best along their longitudinal axes, so texture can raise in-plane conductivity. Texturing by a rotating magnetic field of at least 10 T aligns whiskers before sintering.
Interface engineering determines diamond composite performance
Section titled “Interface engineering determines diamond composite performance”Diamond’s high conductivity and room-temperature expansion of 1 ppm·K⁻¹ make it attractive for heat-spreading composites. The central problem shifts from bulk transport to wetting, interfacial bonding, and continuous pathways.
A vacuum-deposited molybdenum coating on CVD diamond produced a diamond/copper composite with 329 W·m⁻¹·K⁻¹ effective thermal transport. A continuous diamond skeleton with a 300 nm tungsten coating reached 575 W·m⁻¹·K⁻¹ at only 18.4 vol.% diamond.
Time-domain thermoreflectance measured 29.4 MW·m⁻²·K⁻¹ for Cu/W/diamond, 25.8 for Cu/W-W₂C/diamond, and 19.9 for Cu/W₂C/diamond. Diffuse mismatch modeling and molecular dynamics indicated that thinner interconnected carbide layers optimized phonon transmission.
In diamond/aluminum, in situ Al₄C₃ limited conductivity loss to 2% to 5% over 200 cycles from 218 K to 423 K. A composite using 272 µm diamond retained more than 700 W·m⁻¹·K⁻¹ after cycling. A W-coated interface reached 658 W·m⁻¹·K⁻¹ and lost 8.9% after 680 h of water treatment.
Near-GaN integration placed a nearly isotropic diamond layer within 1 nm of the GaN channel. The layer reached 638 ± 48 W·m⁻¹·K⁻¹. Polymer systems showed lower bulk values but greater compliance.
An epoxy with 43.2 wt.% surface-modified diamond reached 22.7 W·m⁻¹·K⁻¹. A silicone system with 80 wt.% single-crystal diamond reached 1.357 W·m⁻¹·K⁻¹. Ice-templated nanodiamond epoxy produced about 16 times the conductivity of neat epoxy at 4.6 vol.% loading. High loading can increase weight, brittleness, and processing cost, so filler volume alone is a poor design criterion.
Filler alignment expands thermal interface design space
Section titled “Filler alignment expands thermal interface design space”Composite performance depends jointly on interface conductance, architecture, and intrinsic filler conductivity. The review identifies 30 to 100 MW·m⁻²·K⁻¹ as a typical target range for TIM interfacial thermal conductance. Engineering requirements include 10% to 60% reversible compressibility and bondline thicknesses of 10 to 100 µm.
Vacuum filtration and hot pressing aligned Ti₃C₂ MXenes at 2.25 vol.% and raised epoxy conductivity to 3.89 W·m⁻¹·K⁻¹. This value was more than 12 times that of neat epoxy. Magnetic alignment at about 35 mT produced 2.25 W·m⁻¹·K⁻¹ in a 50 wt.% BN film, compared with 0.325 W·m⁻¹·K⁻¹ for random fillers.
A vertical graphene array 18.7 µm high produced 53.5 W·m⁻¹·K⁻¹ and 11.8 K·mm²·W⁻¹ contact resistance. Electric-field alignment used a 10 kHz alternating field and strengths up to about 30 V·mm⁻¹.
Atomistic simulations reduced AlN/diamond interface resistance by 28% with rectangular nanopillars. Experiments reported thermal boundary conductance gains up to about 88%. Si/diamond interfaces gained 65% with two-dimensional rectangular structures.
Simulation links atomic behavior to package performance
Section titled “Simulation links atomic behavior to package performance”DFT and MD describe atomic bonding, phonon states, roughness, and stress effects at interfaces. Phase-field models track microstructure evolution without explicitly following every moving interface. Finite-element models then assess coupled thermal, mechanical, and electrical fields in complete packages.
The acoustic mismatch model and diffuse mismatch model provide first estimates, but both assume ideal interfaces and miss mode hybridization. An active-learning Si₃N₄ potential reached a mean absolute error as low as 8 meV·atom⁻¹ and accelerated dynamics by three to four orders of magnitude.
A random-forest model produced a test-set R² of about 0.85, then guided dense β-Si₃N₄ experiments reaching 67.5 W·m⁻¹·K⁻¹. Machine vision on SEM mosaics with AdaBoost predicted ceramic strength with R² above 0.96 and error near 3%. Pore convexity above a threshold near 1.18 marked stronger stress amplification.
Adding predicted relative density to a second-stage model raised test-set R² from 0.75 to 0.80. Small datasets, black-box logic, nonphysical features, and task-specific models still limit transfer.
Commercial performance still lags laboratory records
Section titled “Commercial performance still lags laboratory records”Mass-produced Si₃N₄ substrates typically deliver 70 to 90 W·m⁻¹·K⁻¹, while some experiments exceed 100 W·m⁻¹·K⁻¹. The highest lab-prepared value in the review is 177 W·m⁻¹·K⁻¹, but strength, reliability, and cost constrain commercialization.
Theoretical limits remain unsettled. Earlier work predicted about 450 W·m⁻¹·K⁻¹ for β-Si₃N₄ along the c-axis, while later calculations gave about 169 W·m⁻¹·K⁻¹. The difference reflects assumptions about phonon scattering and defect-free crystals. Glass residues, lattice oxygen, and second-phase distributions can raise conductivity while lowering bending strength.
Spark-plasma sintering has high equipment and processing costs, while pressureless sintering does not reach required densification and performance. TIM scale-up faces a different limit: fillers must form connected paths under assembly pressure and bondline constraints. Interfacial resistance, incomplete percolation, and long-term thermo-mechanical stability can remove gains measured in small specimens.
Package models also struggle to connect thermal cycling, current stress, humidity, oxidation, cracking, and delamination. Machine-learning models face limited data, inconsistent datasets, weak interpretability, and poor transfer across material systems.
Manufacturing yield, reproducibility, process windows, and material compatibility remain unresolved. Many favorable nanoscale results have not yet been demonstrated at wafer or module scale.
Diamond selection depends on interface conditions
Section titled “Diamond selection depends on interface conditions”The review supports selecting diamond by thermal role and interface condition, rather than by intrinsic conductivity alone. For rigid high-flux heat spreaders, continuous metallic networks and stable carbide-forming coatings can improve transport. For compliant TIMs, aligned low-loading networks can reduce thermal resistance while retaining polymer processability.
Surface functionalization can improve diamond/polymer wetting, while excessively thick metal coatings can add interfacial resistance. For near-junction use, measure boundary resistance and graphitization resistance beside bulk conductivity. Specifications should state contact conductance, bondline thickness, thermal cycling, assembly pressure, and required CTE.
Materials and support
Section titled “Materials and support”Power-module TIMs and integrated diamond heat-spreading layers need high-conductivity diamond with controlled surface metallization and geometry. The 6CCVD diamond materials catalog includes MPCVD-grown single-crystal and polycrystalline plates and wafers up to 125 mm, with metallization in Au, Pt, Pd, Ti, W, or Cu. The paper’s near-GaN and composite interface needs make engineering support relevant for custom fabrication support, while qualification remains application-specific.
View Original Abstract
ABSTRACT Current research on integrated circuits and power electronics is rapidly advancing toward miniaturization, high power density, and multi‐chip integration, which presents unprecedented challenges to the thermal management performance of packaging materials. Along the device‐to‐sink heat‐flow path in power modules, thermal management relies primarily on two functional material systems: substrate materials that provide mechanical support and electrical insulation, and thermal interface materials (TIMs) that bridge heat transfer across heterogeneous interfaces. This paper summarizes recent advances in thermal management materials for power electronics, with a focus on ceramic‐based substrate systems, particularly Si 3 N 4 ceramics, and TIM systems including conductive adhesives, diamond‐reinforced composites, and 2D filler-reinforced polymer composites. Emphasis is placed on improvements in thermal conductivity, reduction of thermal resistance, and enhancement of mechanical reliability through process optimization, interfacial engineering, and hybrid filler design. In addition, representative multiscale simulation approaches and emerging applications of artificial intelligence and machine learning are reviewed as tools for understanding interfacial heat transport and accelerating materials screening and optimization. Finally, key challenges and future directions toward scalable, reliable, and intelligent thermal management solutions are discussed, providing guidance for both academic research and industrial deployment in next‐generation power‐electronics packaging.
Electronic Grade Intrinsic Diamond Epitaxial Wafer H Terminated Superior 100 Mosfet Ready Substrate
View Specs →
Advanced Thermal Simulation Service Diamond Heat Spreader Performance Analysis
View Specs →Cvd Diamond Coating On Silicon Wafer
View Specs →References we cover
Section titled “References we cover”- Thermal Conductivity Stability of Interfacial in Situ Al4C3 Engineered Diamond/Al Composites Subjected to Thermal Cycling
- Record-Low Thermal Boundary Resistance between Diamond and GaN-on-SiC for Enabling Radiofrequency Device Cooling
- Tunable Thermal Energy Transport across Diamond Membranes and Diamond-Si Interfaces by Nanoscale Graphoepitaxy
- Interfacial thermal conductance across metal-insulator/semiconductor interfaces due to surface states