Skip to content

Recent Research Advances and Challenges in Diamond Electronic Devices

FieldValue
JournalFunctional Diamond
Published2026-08-20
AuthorsCheng Wang, Chuang Wang, Gengyou Zhao, Bo Feng, Liangxue Gu
DOI10.1080/26941112.2026.2718535

The strongest Schottky-diode result in the reviewed literature came from an Al2O3 field plate. It raised breakdown voltage from 1159 V to 4612 V while leaving specific on-resistance nearly unchanged. The review links this gain to reduced field concentration at the Schottky electrode edge. It also records 3659 V breakdown in an NO2-treated, Al2O3-passivated MOSFET on 5° off-axis Ir/sapphire diamond. These are separate published measurements. The review identifies substrate quality, channel termination, gate dielectric, and edge termination as the main controls on device performance.

The review combines material growth, doping, surface termination, gate dielectrics, device structures, and published electrical measurements. It reports no new fabrication campaign. The authors organize impurity evidence from UV-vis, FTIR, Raman, PL, EPR, and CL. They compare breakdown voltage, on-resistance, forward current, threshold voltage, mobility, and crystal FWHM.

Diamond has a 5.47 eV bandgap and a theoretical breakdown field of 10 MV/cm. Its electron and hole mobilities are 4000 and 3800 cm²/V·s, and its thermal conductivity is 22 W/cm·°C. Relative to silicon, the review lists normalized BFOM, JFOM, and CFOM values of 47708, 8114, and 56677. The authors stress that these are ideal material calculations. Actual devices fall lower because of low doping efficiency, crystal defects, interface states, and electric-field concentration.

HPHT crystals have low defect density, below 10³ cm⁻², but their maximum size is only 1 cm × 1 cm. MPCVD is favored for high-quality films. HFCVD can produce large, uniform films but with lower quality and contamination risk. DC arc plasma jet CVD offers high deposition rates but can incorporate more impurities.

During MPCVD, low-pressure H2 and CH4 are ionized by microwave plasma. Carbon species and hydrocarbon radicals diffuse to the surface. Atomic hydrogen etches graphite and non-diamond carbon while saturating dangling bonds in the diamond film.

Boron is the main p-type dopant, but its activation energy is 0.37 eV. Phosphorus has a 0.57 eV activation energy, while nitrogen has a 1.7 eV ionization energy. Hydrogen can passivate phosphorus and inhibit its ionization. A phosphorus-doped n-channel MOSFET reached about 150 cm²/V·s at 573 K on an atomically flat (111) surface. Hydrogen transfer doping instead creates a two-dimensional hole gas with sheet densities of 10¹² to 10¹⁴ cm⁻² and mobilities below 200 cm²/V·s.

Diode structures set voltage and conduction

Section titled “Diode structures set voltage and conduction”

Measured Schottky-diode results show that a field plate suppresses the Schottky-edge electric-field peak. The review compiles:

Field plateBreakdown without plateBreakdown with plateOther measured result
Al2O31159 V4612 VSpecific on-resistance: 5.34 × 10⁵ mΩ·cm² without; 5.27 × 10⁵ with
HfO2183 V302 VSpecific on-resistance: 4.7 mΩ·cm² without; 4.6 with
SnO2109 V185 VBreakdown field: 2.16 to 4.04 MV/cm; on-resistance 1.31 mΩ·cm²

The Al2O3 result set the record for SBD breakdown in the cited literature. The SnO2 device reached a forward current density of 4740 A/cm². A curved HfO2 plate reached 380 V, compared with 291 V for a traditional plate and 188 V without a plate. A polyimide-trench simulation predicted 1700 V.

The authors state that field-plate material, length, thickness, drift layer, doping, contacts, and device area all affect performance. At 6000 V, a reported SBD had an on-resistance of 300 Ω·cm². At 0.005 Ω·cm², the reported breakdown voltage was 256 V. A field plate shifts this trade-off upward, but most studies examined geometry rather than dielectric-diamond interface physics.

PN-family structures show a different balance. A Schottky PN diode exceeded 4000 A/cm² at about 6 V with 0.4 mΩ·cm² conduction resistance. A Schottky PIN diode reached 116 KA/cm², 0.05 mΩ·cm², and a 6 × 10¹² rectification ratio. Its breakdown voltage was only 47 V because the intrinsic layer was thin. A PIN diode with an 8.5 µm intrinsic layer reached 1040 V. These measurements separate low-voltage conduction from high-voltage blocking.

The channel survey separates current capability from threshold voltage and operating stability.

ChannelReviewed IDmax rangeReviewed Vth rangeMain constraint
Boron-doped0.00019 to 1.2 mA/mm3.2 to 56.1 VLow room-temperature activation
Hydrogen-terminated12 to 200 mA/mm0.37 to 2.2 VAdsorbate and temperature dependence
Silicon-terminated76 to 300 mA/mm5 to 16 VHigher threshold than hydrogen termination

Specific measurements reach higher values than the summary ranges. A heteroepitaxial MOSFET reached 3659 V breakdown and 372 mA/mm maximum drain current. Another device in the review reached 776 mA/mm at 618 V. A 2026 multi-finger MOSFET produced 0.82 A at 550 V using highly boron-doped contacts and a gate field plate.

A 3 nm Al2O3 gate dielectric produced 790 mA/mm drain current and 120 cm²/V·s mobility. An h-BN device reached 680 cm²/V·s effective mobility and 37 mS/mm transconductance at room temperature. Al2O3 also produced a reported interface-state density of 3.19 × 10¹¹ cm⁻²·eV⁻¹. An ALD Al2O3 passivation kept drain current density and transconductance unchanged at 400°C.

Normally-off designs introduce a separate current penalty. A partial C-O channel gave a threshold voltage of 4 V and breakdown above 2 kV, but lower current than C-H devices. A C-H/C-Si-O/C-H device combined 8.6 V threshold, 1376 V breakdown, and 135 mA/mm drain current. Reducing gate length to 0.2 µm produced 1000 mA/mm and 200 mS/mm in another MOSFET.

Large substrates move devices toward wafer scale

Section titled “Large substrates move devices toward wafer scale”

Mosaic bonding can enlarge usable area, but high-density defects form at tile boundaries. Iridium gives the highest reported diamond nucleation density, above 10¹¹ cm⁻². A 4-inch Ir/YSZ/Si heteroepitaxial diamond had an FWHM of 0.16°. A 3.5-inch example reached 0.064°, while a 2-inch Ir/Al2O3 example reached 0.027°. FWHM measures lattice orientation consistency, so lower values indicate better crystalline alignment.

A 1-inch Kenzan diamond substrate had a dislocation density of 1.4 × 10⁷ cm⁻² and an X-ray oscillation FWHM of 113.4 arcsec. The 2-inch substrate supported a 7° off-axis Schottky diode with a 600 nm i-layer. It reached a breakdown field of 2.1 MV/cm. An ion-implanted heteroepitaxial Schottky diode reached 1650 V. A 2 × 2 mosaic device array exceeded 2 MV/cm and was characterized to 40 GHz. These results support wafer processing, but homoepitaxial diodes still outperform heteroepitaxial diodes in breakdown and on-resistance.

Material selection follows the operating constraint. Hydrogen termination favors room-temperature current, but its two-dimensional hole gas depends on humidity and gas adsorbates. Boron-doped channels offer high-temperature resistance despite lower current and higher threshold voltage. Silicon termination offers high-temperature stability and is proposed for more reliable normally-off operation.

The authors suggest combining high-k dielectrics with field plates, improving epitaxial growth, controlling interfaces, and optimizing device geometry. Process control must include humidity, gas atmosphere, heat treatment, dielectric deposition method, and deposition temperature. Plasma during sputtering can damage a hydrogen-terminated surface.

Several issues remain. High-quality n-type layers are difficult to produce. Heteroepitaxial substrates retain high dislocation density and need better area uniformity. The dielectric-diamond interface has received less attention than field-plate geometry. Long-term normally-off reliability also needs threshold drift, high-temperature aging, switching-cycle, and dynamic-response tests. Device selection should therefore use measured data for the intended structure, substrate, channel, and operating environment, rather than the ideal 10 MV/cm material limit.

The paper’s high-power Schottky, PIN, and FET devices require diamond substrates, controlled doping, surface termination where transfer-doped channels are used, and metal contacts. 6CCVD’s MPCVD-grown single-crystal and polycrystalline plates and wafers are available up to 125 mm, with thickness options from 0.1 to 500 micrometers and boron-doped material for p-type channels. The diamond materials catalog lists Au, Pt, Pd, Ti, W, and Cu metallization, while engineering support can help assess device-specific material and fabrication requirements.

View Original Abstract

Diamond possesses excellent physical and electronic properties, and demonstrates great application potential in the next-generation high-power and high-frequency power electronic devices. In recent years, significant progress has been made in the research on diamond diodes and field-effect transistors (FETs). This paper summarizes the effects of channel types, gate dielectrics, substrate types and device structures on the performance of diamond FETs and diodes. The hydrogen-terminated surface provides a high-performance channel for FETs through the formation of a two-dimensional hole gas, while Al2O3 and h-BN and other gate dielectric materials play a key role in reducing interface state density and improving the high-temperature stability of the devices. The development of high-quality 2-inch sapphire heteroepitaxial diamond substrates effectively alleviated the problem of size limitations of diamond substrates, providing a feasible solution for the fabrication of large-area and low-cost diamond devices. The article analyzes the factors that affect the core performance of diamond devices, including breakdown voltage, on-resistance, current density and threshold voltage. The field plate structure can alleviate the edge electric field concentration effect of the Schottky metal, effectively increase the breakdown voltage of the diamond Schottky diode, and does not sacrifice its forward characteristics. We discuss the main bottlenecks and challenges that currently restrict the development of diamond devices. We propose effective strategies to enhance the overall performance of diamond electronic devices from perspectives such as material growth, interface engineering, and structural design. This article aims to provide scientific references for the design and development of high-performance diamond electronic devices.