Skip to content

Diamond anvil cell developed for studying lower-temperature muon-catalyzed fusion reactions

FieldValue
JournalScilight
Published2026-09-04
AuthorsAdam Liebendorfer
DOI10.1063/10.0046588

The MuFusE large-volume diamond anvil cell can compress about 25 curies of tritium in a liquid deuterium-tritium mixture to stable static pressures up to 933 Megapascals. It can be heated to 400 K. The pressure exceeds prior static-pressure reports for this type of experiment and approaches the 800 K temperature at which muon-catalyzed fusion has been demonstrated. The reported result is a pressure capability. It does not establish a new fusion yield or positive energy gain.

The cell’s reported operating envelope is defined by tritium loading, static pressure, and temperature. The tritium inventory is about 25 curies. The stable pressure reaches 933 Megapascals. Heating reaches 400 K. The design target was higher static pressure than seen in previous literature. The authors also sought density and temperature combinations not covered by earlier work.

QuantityReported valueCondition or comparison
Tritium inventoryAbout 25 curiesIn a liquid deuterium-tritium mixture
Stable static pressureUp to 933 MegapascalsAbove prior literature reports
Cell temperatureUp to 400 KBelow the 800 K demonstration
Fusion events per muonUp to 150Measured in previous experiments
Muon-to-electron mass ratioApproximately 200Basis for muonic atom contraction

The numbers describe different parts of the program. Pressure and temperature are MuFusE cell capabilities. The 150-fusion figure is a result from previous experiments. The mass ratio explains why muon catalysis changes the reaction conditions. The Scilight report gives no MuFusE value for fusions per muon.

A muon has approximately 200 times the mass of an electron. When a muon replaces an electron in a hydrogen isotope, the resulting muonic atom is proportionately more compact. Reduced internuclear spacing increases quantum tunneling through the Coulomb barrier. This mechanism is the stated reason that muon catalysis can lower the fusion threshold temperature.

The report says muon-catalyzed fusion has shown promise for thermonuclear fusion at temperatures more than one ten-thousandth of conventional thermonuclear fusion. That statement describes the method’s potential. It is not a MuFusE temperature result.

MuFusE provides a controlled setting for measuring reactions at new density and temperature combinations. The team hopes higher density and higher temperature will raise the number of fusions per muon. The cell also keeps optical access available at high pressure. Pressure provides the route to the higher densities sought by the team, while temperature provides the second experimental variable.

Kalow et al. combined four elements in the pressure cell: cryogenic loading, all-metal sealing, flexible bellows, and secondary containment. Together, these features support safe filling and compression of the deuterium-tritium mixture. The cryogenic step matches the reported liquid state of the fuel. The report presents the elements as one design for filling and compressing the sample at static pressure.

The loaded cell is then placed within a detector apparatus in front of a high-intensity muon beam. The muons are directed at the compressed mixture. The diamond anvils retain pressure while providing optical access. This makes the device a measurement platform as well as a pressure vessel.

The design carries about 25 curies of tritium through loading and compression. It integrates fuel containment, pressure retention, heating to 400 K, and access for the detector. The report treats these functions as one sealed assembly. It does not present separate performance data for the diamond and the surrounding containment components.

The experimental arrangement links the loaded cell, a high-intensity muon beam, and a detector apparatus. Kalow said the techniques were designed to bring the mixture to higher static pressures for measurements at novel density and temperature combinations. The intended measurement is muon-catalyzed fusion under controlled static pressure and temperature.

Previous experiments measured up to 150 fusions per muon. That value is the team’s benchmark, not a result achieved by MuFusE in this report. The authors hope that higher density and higher temperature will move the fusion count above the benchmark. They also state a separate goal of positive fusion energy gain.

Neither the higher count nor positive energy gain is presented as achieved. The report gives the cell capability without giving a MuFusE reaction-performance value. The authors plan to continue updating the DAC design to push performance further.

The Scilight report names the detector apparatus but does not describe its type or event reconstruction. It gives no beam flux, exposure time, run count, measurement uncertainty, or energy balance for MuFusE. It also gives no new fusions-per-muon value. Without that count, the article cannot show whether the added pressure produced more fusion events.

Although the source calls MuFusE a large-volume cell, the report gives no sample or working volume. It also does not describe pressure calibration, cell wall thickness, or temperature measurement. These missing details limit how closely another laboratory could reproduce the cell conditions.

Important diamond specifications are also missing. The report does not state diamond grade, crystallographic orientation, anvil dimensions, surface finish, optical properties, or behavior after exposure to the tritium mixture. It provides no direct comparison between diamond types and no isolated diamond test data for the stated conditions. The paper therefore cannot by itself identify a production diamond for the cell.

The diamond has a defined device role. It forms the anvil pressure boundary while maintaining optical access to the compressed sample. The surrounding system includes an all-metal seal, flexible bellows, secondary containment, cryogenic loading, and a detector position in front of a muon beam.

A candidate material and its assembly should be assessed against the reported 933 Megapascals and 400 K conditions. The liquid deuterium-tritium state and the actual sealing geometry also form part of that assessment. These conditions should be checked at assembly level rather than inferred from an isolated diamond specimen.

The 933 Megapascals and 400 K values define the component operating envelope. They do not establish a production specification without dimensions, surface finish, or optical data. Future revisions may seek higher performance. The material requirement should then follow the revised cell rather than the initial operating envelope.

MuFusE uses diamond anvils for pressure containment and optical access at 933 Megapascals and 400 K. 6CCVD’s diamond materials catalog lists MPCVD-grown single-crystal and polycrystalline plates and wafers up to 125 mm, with thickness from 0.1 to 500 micrometers. The paper does not specify anvil dimensions, surface finish, or production method, so engineering support can assess a custom geometry against the reported conditions.

View Original Abstract

Device pushes boundaries of experimental pressures and temperatures in the study of muons, whose greater mass significantly lowers fusion threshold temperatures when replacing electrons in hydrogen isotopes.