Skip to content

Coupling a Single Nitrogen-Vacancy Center in Nanodiamond to Superparamagnetic Nanoparticles

MetadataDetails
Publication Date2018-05-24
JournalScientific Reports
AuthorsNikola Sadzak, M Héritier, Oliver Benson
InstitutionsHumboldt-Universität zu Berlin, ETH Zurich
Citations25
AnalysisFull AI Review Included
  • Core subject: Coupling a single nitrogen-vacancy (NV) center in a type Ib nanodiamond (~25-50 nm) to a single superparamagnetic iron oxide nanoparticle (SPION, ~10 ± 1 nm) via AFM pick-and-place nanomanipulation.
  • Method: Bottom-up deterministic assembly using a high-NA confocal microscope combined with an AFM on a photolithographically patterned Au coplanar waveguide (CPW) and Helmholtz coil pair delivering up to 40 G static fields.
  • Key relaxometry result: The longitudinal spin relaxation time T1 collapsed from 474 ± 136 µs (bare NV) to 13 ± 2 µs when the SPION was positioned < 100 nm away — a > 30× drop.
  • Key Hahn-echo result: T2 was essentially unaffected (1.74 ± 0.06 µs → 1.69 ± 0.07 µs), proving the high-frequency SPION noise interacts with the NV center’s free-induction but not its echo-protected coherence.
  • Key Rabi shift: A driving AC field of 12.0 G at 2.855 GHz produced a ∆ωR = 90 ± 70 kHz shift, indicating the SPION contributes an in-phase AC field of ~45 ± 35 mG at the NV location.
  • Innovation: Exploits intrinsic crystal strain to lift the ms = ±1 degeneracy — eliminating the need for an external DC bias field — simplifying integration into miniaturized quantum sensor heads.
  • Strategic implication: SPIONs can act as local flux concentrators/amplifiers that compensate for the inherently short T2 of nanodiamonds, opening a route to high-sensitivity, room-temperature AC nanomagnetometry.

ParameterValueUnitContext
Nanodiamond typeType Ib—High N impurity, ~27 nm average diameter (Microdiamant QP25)
Single NV center per particle1countPre-selected via g(2)(0) antibunching
SPION compositionIron oxide (magnetite/maghemite)—FCC lattice, 8 Fe2+ in octahedral sites
SPION diameter10 ± 1 (used 11 nm)nmDiluted in toluene, spin-coated
Surface SPION density~few / 10 µm2µm⁻²Achieved by dilution
NV-SPION separation (manipulated)50 - 100 (64 ± 3)nmAFM contact-mode positioning
Bare NV T1 (ms = 0)474 ± 136µsLongitudinal decoherence
Coupled NV T113 ± 2µsWith SPION at < 80 nm
Bare NV T2 (Hahn-echo)1.74 ± 0.06µsInhomogeneous dephasing
Coupled NV T21.69 ± 0.07µsEcho-protected, dominated by N bath
Bare NV T2*550 ± 50nsFree-induction decay
NV gyromagnetic ratio γNV2π × 2.8MHz/GFree-electron value
NV zero-field splitting (calc.)2.855GHzms = 0 → ms = −1 transition
Magnetic field stability window2854.5 - 2854.9MHzResonance monitored across experiment
Driving AC field BAC12.0 ± 0.1GApplied via Au CPW
Rabi frequency (bare)7.33 ± 0.05MHzAt constant MW power
Rabi frequency (coupled)7.24 ± 0.05MHzWith SPION at 64 nm
Rabi shift ∆ωR90 ± 70kHzIndicates SPION-induced AC field
Effective AC field decrease45 ± 35mGFrom Rabi shift
Simulated SPION ⟨mz′⟩ at 12.0 G~1.3 × 10³µBNet in-phase magnetic moment
Simulated SPION-generated z′-field at 64 nm~23mGMatches experiment
Magnetic noise variance ⟨Bxy²⟩2.9 ± 0.5G²Deduced from T1 drop
Neel relaxation time τN5.5 × 10⁻¹¹sWith τ0 = 5 × 10⁻¹² s
Anisotropy constant K14kJ/m³Magnetite
Static field capabilityup to 40G per axisHelmholtz coil pair
NV axis deviation from x′ coil axis72 ± 1degFrom 2D static field mapping
MW field angle to NV axis φ18 ± 1degFrom Rabi fit
Laser excitation532nmPulsed via AOM
ObjectiveOlympus UPLANSAPO 100× oil—NA = 1.40
Substrate / dielectricSiO₂ cover slide, 0.15 mm thick—Piranha + Hellmanex cleaned
Metal layerAu impedance-matched CPW—Photolithographic patterning
AFM cantilever (manipulation)Arrow-FM (Si) / NSC35/Pt—Pick-and-place

  1. Substrate fabrication: Photolithographic patterning of a 0.15 mm SiO₂ cover slide with a gold impedance-matched microwave coplanar waveguide (CPW) to deliver an AC magnetic field orthogonal to the surface.
  2. Surface cleaning: Piranha solution (3:1 H₂SO₄/30% H₂O₂) followed by 1% Hellmanex III sonication and distilled water rinse to remove organic and particulate contaminants.
  3. SPION deposition: Dilute iron oxide/toluene suspension spin-coated onto the CPW support, yielding a sparse distribution (~few particles per 10 µm²).
  4. Nanodiamond preparation: Type Ib diamond nanoparticles (~27 nm, Microdiamant QP25) spin-coated onto a second CPW slide; single NV centers identified by confocal fluorescence and g(2)(0) antibunching.
  5. Deterministic pick-and-place: AFM (NSC35/Pt cantilever) transfers a single pre-characterized nanodiamond from the secondary slide onto the SPION-decorated CPW; success verified via fluorescence and photon statistics.
  6. NV positioning: Final nanodiamond located ~700 nm from the SPION cluster; isolated SPION then AFM-manipulated to a controlled NV-SPION distance of 50-100 nm.
  7. Magnetic environment characterization: 2D Helmholtz static field (≤ 40 G per axis) used to map NV axis orientation: 72 ± 1° from x′ coil axis, MW field angle φ = 18 ± 1° to NV quantization axis.
  8. Spin-state measurement: Pulsed 532 nm laser (AOM-modulated) for spin polarization and readout; resonant microwave pulses at 2.855 GHz from the CPW.
  9. Relaxometry sequence: Two-laser-pulse T1 measurement of the ms = 0 state with variable free-evolution time τ.
  10. Hahn-echo sequence: Polarizing laser → π/2 - π - π/2 microwave pulse train to measure T2 insensitivity to low-frequency noise.
  11. Rabi oscillation measurement: Constant-power MW drive at the ms = 0 → ms = ±1 transition with crystal strain used to lift the ms = ±1 degeneracy (no external DC bias required).
  12. Data analysis: Brown / Néel-Arrhenius / Casimir-DuPré models used to extract τN, ⟨Bxy²⟩, and the in-phase SPION AC magnetization from the measured T1 and ∆ωR.

  • Optical Grade Single Crystal Diamond (SCD) — Detonation & HPHT nanodiamonds (4-50 nm): The paper relies on sub-50 nm type Ib nanodiamonds with isolated NV centers. 6CCVD can supply custom-sized nanodiamond powders and precision-dropcast suspensions with controlled nitrogen density for NV yield optimization.
  • Electronic Grade Single Crystal Diamond (SCD) wafers: For researchers transitioning from nanodiamond probes to bulk scanning-NV magnetometry on engineered hybrid devices, 6CCVD’s low-nitrogen ([N] < 1 ppb) SCD substrates deliver two orders of magnitude longer T2* — essential when the SPION’s role shifts from a probe to a local amplifier.
  • Boron-Doped Diamond (BDD): For parallel work requiring conductive diamond electrodes (e.g., combined electrochemical and magnetic control of SPIONs in a hyperthermia / drug-delivery context), BDD grades from 100 ppm to 10⁴ ppm are available.
  • Polycrystalline Diamond (PCD) wafers up to 125 mm: For scaling up the CPW-patterned platform to wafer-level sensor arrays, PCD provides uniform microwave performance and is compatible with photolithographic Au patterning and nanodiamond grafting.
  • Custom metalization (Au / Ti / Pt / Pd / W / Cu): The Au impedance-matched CPW used here is a perfect match for 6CCVD’s in-house Au metallization. We can co-furnish Ti/Au or Cr/Au adhesion stacks, and Pt or Pd capping layers for harsh chemical environments (e.g., biosensing in physiological buffers).
  • Laser cutting & dicing: Nanodiamonds in this work are ~27 nm — well below dicing tolerance. However, for bulk NV-magnetometry follow-on studies that require cantilever or scanning-probe geometries, 6CCVD provides laser micro-machining to ±1 µm edge placement on SCD and PCD.
  • Surface polishing: Sub-nm Ra (SCD) and < 5 nm (PCD) polishing is critical for AFM pick-and-place reliability; 6CCVD’s atomically smooth surfaces minimize particle drift during manipulation.
  • Thickness control: Custom thicknesses from 0.1 µm freestanding SCD membranes (for transmission-mode NV readout) to 10 mm substrates (for high-stiffness AFM supports) are available on request.
  • PhD-led consultation: 6CCVD’s in-house PhD team can guide your material selection across the NV-center design space — from Type Ib nanodiamonds matched to your target T2/T1 ratio, to isotopically engineered 12C-enriched SCD for ultra-long coherence, down to BDD electrodes for SPION hyperthermia integration.
  • Application-specific guidance: For quantum sensing, hybrid nanomagnetometry, relaxometry, single-photon source, and biosensing NV projects, our engineers can recommend the optimal SCD/PCD/BDD grade, crystal orientation (100/110/111), and metallization stack for your specific magnetic field strength and frequency band.
  • Prototype-to-wafer scaling: Whether you need a single research-grade nanodiamond sample or a 125 mm PCD wafer for a sensor-array pilot line, 6CCVD supports both with consistent quality.

For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

Abstract Single nitrogen-vacancy (NV) defect centers in diamond have been exploited as single photon sources and spin qubits due to their room-temperature robust quantum light emission and long electron spin coherence times. They were coupled to a manifold of structures, such as optical cavities, plasmonic waveguides, and even injected into living cells to study fundamental interactions of various nature at the nanoscale. Of particular interest are applications of NVs as quantum sensors for local nanomagnetometry. Here, we employ a nanomanipulation approach to couple a single NV center in a nanodiamond to a single few-nm superparamagnetic iron oxide nanoparticle in a controlled way. After measuring via relaxometry the magnetic particle spin-noise, we take advantage of the crystal strain m s = ± 1 spin level separation to detect the superparamagnetic particle’s effect in presence of a driving AC magnetic field. Our experiments provide detailed insight in the behavior of such particles with respect to high frequency fields. The approach can be extended to the investigation of increasingly complex, but controlled nanomagnetic hybrid particle assemblies. Moreover, our results suggest that superparamagnetic nanoparticles can amplify local magnetic interactions in order to improve the sensitivity of diamond nanosensors for specific measurement scenarios.