Single-longitudinal-mode diamond laser stabilization using polarization-dependent Raman gain
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2019-03-15 |
| Journal | OSA Continuum |
| Authors | Soumya Sarang, Ondřej Kitzler, Oliver Lux, Zhenxu Bai, Robert J. Williams |
| Institutions | Macquarie University, Deutsches Zentrum für Luft- und Raumfahrt e. V. (DLR) |
| Citations | 27 |
| Analysis | Full AI Review Included |
Executive Summary
Section titled “Executive Summary”- Objective: Develop a Hänsch-Couillaud (HC) variant locking mechanism for single-longitudinal-mode (SLM) continuous-wave diamond Raman lasers (DRL), bypassing the need for etalons, injection seeding, or ring cavities.
- Key Innovation: The locking signal was generated using polarization-dependent Raman gain (gain anisotropy) and stress-induced birefringence in CVD single-crystal diamond (SCD) instead of conventional intracavity Brewster plates.
- Performance Leap: Stable SLM output power was scaled from 2.1 W (free-running) to 7.2 W (stabilized), with sustained stability improving from “tens of seconds” to 120 seconds at 4.5 W.
- Crystal Specifications: The research utilized an 8 × 4 × 1.2 mm3 low-nitrogen, low-birefringence SCD with propagation along the <110> axis, anti-reflection (AR) coated at both pump (1064 nm) and Stokes (1240 nm) wavelengths.
- Critical Findings: The 1064 nm pump source (Yb-fiber amplified, 50 W, M2 = 1.05) was polarized along the <111> axis for maximum Raman gain, while the diamond’s intrinsic birefringence (∆n ≈ 5 × 10−6) and Raman pump-depletion rotation provided the polarization-dependent loss mechanism essential for the HC locking signal above threshold.
- Limitation & Next Step: Locking was ultimately restricted by the piezo-stage slew rate (154 Hz) and low cavity finesse at the pump wavelength. The paper mathematically demonstrates that increasing ∆n to 1.7 × 10−5 - 3.2 × 10−5 would yield a robust dispersion-like locking signal.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Pump Source | 1064 | nm | Yb-fiber amplified DFB laser (CW) |
| Pump Power | 50 | W | Maximum available output |
| Pump Linewidth | 5 | MHz | Narrower than 45 GHz Raman gain bandwidth |
| Beam Quality (M²) | 1.05 | - | Near diffraction-limited |
| Stokes Wavelength | 1240 | nm | First Stokes shift |
| Threshold Pump Power | 23 | W | Stokes lasing threshold |
| Slope Efficiency | 70 | % | Unstabilized CW operation |
| SLM Power (Free-running) | 2.1 | W | Baseline before active locking |
| SLM Power (Stabilized) | 7.2 | W | Maximum achieved with HC locking |
| SLM Stability Duration | 120 | s | At 4.5 W output power |
| Wavelength Stability | 125 | MHz | Fluctuation range over 2 mins |
| Raman Gain Bandwidth (FWHM) | 45 | GHz | Homogeneous broadening regime |
| Cavity Length | 102 | mm | Near-concentric standing-wave cavity |
| Mirror Radius of Curvature | 50 | mm | Concave input/output couplers |
| Diamond Dimensions | 8 × 4 × 1.2 | mm³ | Length × Width × Thickness |
| Diamond Birefringence (∆n) | 5 × 10−6 | - | Stress-induced, near-IR |
| Propagation Direction | <110> | - | Crystallographic orientation |
| Pump Polarization | <111> | - | Orientation for maximum Raman gain |
| Input Coupler (IC) Trans. | 99.26 (1064nm) / 0.06 (1240nm) | % | Highly transmitting / Highly reflective |
| Output Coupler (OC) Trans. | 0.5 (1240nm) | % | Partially transmitting at Stokes |
| AR Coating Reflectivity | < 1 (1064nm) / < 0.25 (1240nm) | % | Diamond end-face coatings |
| Round-Trip Dephasing (∆) | 0.5 | rad | Calculated birefringence-induced phase |
| PZT Travel Range | 20 | µm | 0 - 75 V applied voltage |
| PZT Slew Rate | 154 | Hz | Limiting factor for locking bandwidth |
| Intracavity Loss (Absorption) | 0.017 | %/mm | At pump wavelength |
| Intracavity Loss (Reflection) | 0.1 | %/face | At crystal end-faces |
Key Methodologies
Section titled “Key Methodologies”- Cavity Design: Constructed a simple standing-wave, near-concentric cavity (102 mm length, 50 mm ROC mirrors) devoid of frequency-selective elements to test the HC locking hypothesis.
- Crystal Preparation: Used low-nitrogen, low-birefringence CVD-grown single-crystal diamond, cut for <110> propagation, with AR coatings on both faces to minimize intracavity losses.
- Pump Alignment: Focused the 1064 nm pump beam (50 mm focal length lens, 40 µm spot radius) into the center of the diamond with polarization oriented along the <111> axis for maximum stimulated Raman scattering efficiency.
- Locking Signal Generation: Implemented a Hänsch-Couillaud setup using a quarter-wave plate (QWP), polarizing beam splitter (PBS), and two photodiodes to analyze residual pump polarization after double-passing the cavity.
- Theoretical Modeling: Developed a MATLAB model based on four coupled differential equations (Eqs. 4a-4d) to simulate pump depletion and Stokes generation for orthogonal polarizations, validating that polarization rotation above threshold generates the locking signal.
- Active Stabilization: Drove a piezoelectric translation stage (PZT) holding the output coupler via a PID controller (Laselock digital), targeting the zero-crossing of the locking signal.
- Spectral Characterization: Monitored output using a scanning Fabry-Perot interferometer (67 MHz resolution, 10 GHz FSR), an optical spectrum analyzer (0.05 nm resolution), and a Bristol 771A-NIR laser spectrum analyzer for wavelength stability tracking.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”This research highlights the critical role of high-purity, low-loss, and precisely engineered Single Crystal Diamond (SCD) in advancing high-power, single-frequency laser architectures. Below is how 6CCVD directly addresses the requirements identified in this paper.
- Applicable Materials: To replicate or extend this research, Optical Grade Single Crystal Diamond (SCD) is required. The study specifically utilized low-nitrogen, low-birefringence CVD diamond to minimize parasitic absorption and optical loss. 6CCVD specializes in manufacturing ultra-low-loss SCD substrates and plates engineered explicitly for high-power laser gain media where thermal and optical stability are paramount.
- Customization Potential: The paper utilized a specific 8 × 4 × 1.2 mm3 geometry cut along the <110> axis with custom AR coatings (R < 1% at 1064 nm, R < 0.25% at 1240 nm). 6CCVD offers custom diamond shaping and laser cutting up to wafer-scale dimensions, alongside in-house dielectric coating capabilities to meet these exacting specifications. Furthermore, 6CCVD provides custom metallization (e.g., Ti/Pt/Au) which is frequently essential for securely mounting diamond crystals onto thermal heat sinks or piezo-electric transducers (PZT) without introducing mechanical stress that could alter the birefringence profile.
- Engineering Support: The authors identified that increasing the diamond’s intrinsic birefringence (∆n) to the 10−5 range would significantly improve the HC locking signal. 6CCVD’s in-house PhD engineering team can collaborate on material selection, advising on the trade-offs between stress-induced birefringence control and crystal orientation (<110>, <111>, <100>) to optimize Raman gain anisotropy for next-generation stabilized laser cavities. Whether the application is spectroscopy, gravitational wave sensing, or LIDAR, our experts can tailor the SCD optical and mechanical properties to your project requirements.
- Call to Action: For custom specifications, AR coating designs, or material consultation regarding your diamond Raman laser architecture, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
We report a novel cavity feedback mechanism for stabilizing single-longitudinal-mode (SLM) operation of diamond Raman lasers. Polarization-dependent Raman gain and in-grown stress birefringence in diamond were investigated as sources for Hänsch-Couillaud-type locking signals. The power range of SLM operation increased from 2.1 W to 7.2 W, compared to the free-running laser, for a simple standing-wave laser cavity without frequency-selective elements. Methods for further increasing power range and frequency stability are discussed.