An Impact-based Automatic Centering Actuator System for Ultra-Precision Turning
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2022-01-01 |
| Journal | Asian Society for Precision Engineering and Nanotechnology (ASPEN 2022) |
| Authors | Seung-Kook Ro, Gyungho Khim, Doo‐Sun Choi |
| Institutions | Korea Institute of Machinery and Materials |
| Analysis | Full AI Review Included |
Executive Summary
Section titled “Executive Summary”- System Overview: Development of an impact-based automatic centering actuator system designed for ultra-precision diamond turning of micro lens core molds, replacing manual setup with automated alignment.
- Core Achievement: Successfully aligned workpiece center to within 1 µm eccentricity in under 20 seconds, achieving convergence in approximately 14 seconds during experimental trials.
- Mechanism: Dual-mass impact actuator utilizing a voice coil motor (VCM) generating up to 500 N impact force from 7.6 N excitation force, displacing the workpiece during continuous spindle rotation.
- Control Architecture: Real-time LMS (least-mean-square) tracking algorithm implemented on a low-cost ATmega128 MCU (Arduino) to estimate eccentricity and modulate compensation output.
- Application: Integrated with a diamond turning machine (DTM) operating at 60 rpm spindle speed and 20 Hz excitation frequency for micro lens core mold production.
- Impact Profile: Short impact duration (<1 ms) permits centering without spindle stopping; measured impact force up to 400 N at 0.15 A drive current.
- Industry Relevance: Reduces setup time for mass production of high-resolution lens modules demanded by mobile electronics and autonomous mobility applications.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Target Eccentricity | < 1 | µm | Final alignment precision after auto-centering |
| Convergence Time | ~14 | seconds | Measured experimental centering duration |
| Maximum Allowable Time | 20 | seconds | Design specification deadline |
| Spindle Rotational Speed | 60 | rpm | Continuous rotation during centering |
| Excitation Frequency | 20 | Hz | Square wave compensation signal |
| Impact Force (Simulated) | Up to 500 | N | Generated per impact cycle |
| Impact Force (Measured) | Up to 400 | N | Verified on test bed |
| Excitation Force | 7.6 | N | Input to voice coil motor |
| Drive Current | 0.15 | A | Required for 400 N impact force |
| Coil Current per Force | 1 | A | Generates 7.6 N excitation |
| Impact Mass (m1) | 0.104 | kg | Primary moving/contact mass |
| Secondary Mass (m2) | 0.268 | kg | Reaction mass |
| Impact Duration | < 1 | ms | Duration of single impact event |
| Minimum Force to Move Workpiece | 43 | N | Threshold for overcoming friction |
| Displacement per Unit Force | 0.14 | mm/N | Above 1 µm displacement threshold |
| LVDT Sensor Resolution | 5 | nm | Capacitive sensor for runout measurement |
| MCU Platform | ATmega128 | — | Low-cost microcontroller for control |
| Impact Frequency | 20 | Hz | Excitation rate for compensation |
Key Methodologies
Section titled “Key Methodologies”- System Design: Dual-mass impact actuator with voice coil motor (VCM) positioned between mass m1 (0.104 kg) and mass m2 (0.268 kg), guided by miniature linear motion (LM) guides.
- Numerical Simulation: Verified force generation of up to 500 N from 7.6 N excitation, confirming velocity amplification via mass ratio.
- Testbed Validation: Force sensors and laser displacement sensors measured movements to confirm simulation; impact hammer test quantified workpiece friction threshold (43 N).
- Eccentricity Estimation: LMS (least-mean-square) algorithm tracks synchronous signal filtered from LVDT sensor to estimate real-time runout.
- Compensation Logic: Continuous square wave output at 20 Hz with amplitude modulation in two stages—coarse impact for high eccentricity, fine amplitude for minimal displacement.
- Hardware Integration: ATmega128 Arduino MCU programmed with tracking algorithm; D/A converter drives current amplifier connected to VCM.
- Experimental Trial: Diamond turning machine (DTM) at 60 rpm spindle speed; LVDT sensor installed opposite the actuator; test concluded with runout below 1 µm in 14 seconds.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”- Applicable Materials:
- Optical-Grade Single Crystal Diamond (SCD): The paper focuses on diamond turning of micro lens core molds, which requires ultra-precision tooling. 6CCVD’s optical-grade SCD with sub-nanometer surface roughness (Ra < 1 nm) is ideal for extended machining accuracy in such high-resolution optical mold manufacturing.
- Polycrystalline Diamond (PCD) Cutting Tool Inserts: For diamond turning applications requiring wear resistance on non-ferrous optical materials, 6CCVD’s PCD plates (up to 125 mm diameter) provide the durability needed for continuous mold production.
- Customization Potential:
- Custom Dimensions: If your research requires specific diamond tool geometries or substrate dimensions for ultra-precision turning of optical molds, 6CCVD offers custom SCD and PCD plates in thicknesses from 0.1 µm to 500 µm, with substrates up to 10 mm.
- Metalization for Tool Integration: For diamond tools requiring brazed or soldered mounting in automated centering fixtures, 6CCVD provides in-house metalization (Ti, Cr, Au, Pt, Pd, W, Cu) to ensure robust thermal and mechanical integration.
- Laser Cutting Services: Custom diamond tooling geometries for lens core machining can be precision-cut to your specifications.
- Engineering Support:
- Material Selection for Ultra-Precision Machining: 6CCVD’s in-house PhD engineering team can assist in selecting the optimal diamond grade (SCD vs. PCD vs. BDD) and surface finish specification for your specific optical mold machining application, whether for micro lens cores, aspheric molds, or freeform optics.
- Application Consultation: For projects targeting sub-micron form accuracy in lens module manufacturing, our team can recommend material parameters that complement your automated centering and ultra-precision turning workflows.
- Call to Action: For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
In this paper, we introduces an automatic workpiece centering system using an impact actuator for future use of automating centering process which is currently done bv time-consuming manual process.We were aimed to develop an actuator and automatic process to align workpiece center within 20 seconds.An impact actuator was designed to generate force to move work small displacement by continuously impacting during rotation.The proposed impact actuator has a voice coil motor for generating movements of two masses which are guided by miniature guides, and mass with smaller weight contacts workpiece.The measured eccentricity by a displacement was estimated on-line through LMS tracking method, and magnitude of excitation was calculated based on the tracked eccentricity.The proposed actuator was manufactured and integrated with a control system using low-cost micro-processor.The automatic centering actuator system was applied to a diamond turning machine for a micro lens core mold with continuous rotating speed of 60 rpm and 20 Hz of excitation frequency.It was demonstrated experimentally that centering workpiece was possible within 1 Pm and no more than 20 seconds.