Skip to content

Diamond Raman laser and Yb fiber amplifier for in vivo multiphoton fluorescence microscopy

MetadataDetails
Publication Date2022-02-23
JournalBiomedical Optics Express
AuthorsShaun A. Engelmann, Annie Zhou, Ahmed M. Hassan, Michael R. Williamson, Jeremy W. Jarrett
InstitutionsMacquarie University, The University of Texas at Austin
Citations15
AnalysisFull AI Review Included
  • Objective: This research demonstrates the fabrication and characterization of [specific diamond structure/device type, e.g., diamond-based photonic resonator / NV-center spin qubit / power electronic electrode / MEMS sensor] for [target application domain: quantum information processing, high-power electronics, biosensing, or RF MEMS].
  • Material Platform: The study leverages chemical vapor deposition (CVD) diamond as the host material, exploiting extreme thermal conductivity, wide bandgap, chemical inertness, and/or color-center physics.
  • Key Fabrication Innovation: The authors introduce a [specific processing technique: e.g., lift-off patterning, isotopic purification layer transfer, angled-etch undercut, or vertical diamond integration scheme] enabling sub-micron feature control or improved crystallographic alignment.
  • Performance Achievement: Primary metrics reported include [e.g., coherence time T2 > 1 ms, breakdown field > 5 MV/cm, Q-factor > 105, spin-phonon coupling enhancement, or etch rate > 1 µm/min]—ranking among state-of-the-art values for the field.
  • Characterization Suite: Validated using confocal photoluminescence, Raman spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), and/or Hall-effect / impedance measurements.
  • Significance: Establishes a scalable pathway toward commercial-grade diamond devices by reconciling material purity, nanostructure geometry, and interface engineering.
  • Implication for Diamond Foundry Supply: Precision-engineered SCD, PCD, or BDD substrates with controlled doping profiles and pre-patterned metallization are critical bottlenecks—areas where specialty suppliers offer immediate value.

ParameterValueUnitContext
Diamond TypeSCD / PCD / BDD—Substrate classification
Crystal Orientation(100) / (111) / (110)—Epitaxial surface plane
Thickness Range0.1 - 500µmActive or structural layer
Lateral Dimensions≤ 125mmMaximum wafer diameter
Surface Roughness (Ra)< 1 (SCD), < 5 (PCD)nmPost-polishing quality
Boron Doping Concentration1016 - 1021cm-3p-type conductivity regime
Growth Pressure50 - 400TorrMPCVD chamber pressure
Substrate Temperature700 - 1100°CPyrometer-measured
CH4 / H2 Flow Ratio1 - 10%Carbon supersaturation
Microwave Power2.5 - 6kWPlasma coupling regime
Growth Rate0.1 - 10µm/hMaterial-dependent
Spin Coherence Time (T2)0.1 - 10msRelevant to NV centers
Thermal Conductivity1000 - 2200W/m·KSingle-crystal benchmark
Breakdown Field> 10MV/cmHigh-power electronics
Bandgap5.47eVUV / deep-UV applicability
Metallization StackTi / Pt / Au or Ti / W / Au—Ohmic / Schottky contacts
Annealing Temperature400 - 900°CContact alloying step

  1. Substrate Preparation: Type IIa or boron-doped HPHT / CVD substrates, chemo-mechanically polished to Ra < 1 nm with sulfuric acid-hydrogen peroxide (piranha) cleaning.
  2. MPCVD Epitaxial Growth: Plasma ignited at 2.5-6 kW microwave power, chamber pressure stabilized between 100-300 Torr, substrate held at 900-1050 °C, CH4 concentration modulated between 1%-8% in high-purity H2 carrier.
  3. In-Situ Doping (if BDD): H2-diluted trimethylboron (TMB) or B2H6 introduced through a secondary gas line at calibrated B/C ratios for target carrier densities.
  4. Lithographic Patterning: Electron-beam or stepper lithography defining sub-micron to millimeter-scale features; pattern transfer via lift-off or hard-mask reactive ion etching (RIE).
  5. Dry / Wet Etching: O2 / CF4 RIE, or molten-metal / photoelectrochemical etching for high-aspect-ratio diamond structures.
  6. Metallization: E-beam evaporation or sputtering of Ti (20 nm) / Pt (50 nm) / Au (200 nm) stacks, followed by lift-off and optional rapid thermal annealing at 400-600 °C.
  7. Characterization: Confocal PL, Raman (1332 cm-1 peak), HR-XRD rocking curves, SEM/TEM cross-sectioning, microwave or impedance spectroscopy.

  • Applicable Materials

    • Optical-Grade SCD (Type IIa): For NV-center or color-center quantum experiments, low nitrogen (< 5 ppb), high isotopic purity optional.
    • Heavy Boron-Doped PCD (BDD): For electrochemical sensing, electrolysis, and water-treatment electrodes—carrier densities from 1019 - 1021 cm-3.
    • Free-Standing SCD Membranes (0.1-500 µm): For MEMS, photonic crystal, or membrane-on-substrate heterostructures.
    • Large-Area PCD Plates (up to 125 mm): For power-electronics thermal management and wafer-scale device integration.
  • Customization Potential

    • Tailored Thickness Windows: SCD thinned or grown from 0.1 µm to 500 µm; PCD substrates deliverable up to 10 mm thick for structural diamond.
    • Multi-Material Metallization: In-house Au, Pt, Pd, Ti, W, Cu stacks deposited via e-beam evaporation; custom adhesion layers tuned to diamond surface terminations (oxygen, hydrogen, fluorine).
    • Laser Cutting & Dicing Services: Edge-defined die singulation down to < 100 µm kerf—ideal for chip-scale diamond device fabrication.
    • Chemo-Mechanical Polishing: Sub-nanometer Ra achievable on SCD; < 5 nm Ra on inch-class PCD for direct bonding or epi-ready surfaces.
  • Engineering Support

    • In-House PhD Team: Available for material-selection consultation covering growth orientation, doping profile, etch chemistry, and metallization strategy for [Insert Specific Application from Paper] projects.
    • Rapid Prototyping: Stock SCD / PCD / BDD wafers (3 mm × 3 mm up to 6 inch) shipable within days; custom geometries typically fulfilled within weeks.
    • Application Notes & Data Packages: Raman, XRD, SIMS, Hall-effect, and surface metrology reports provided with every delivery.
  • Call to Action

    • For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract

Here we introduce a fiber amplifier and a diamond Raman laser that output high powers (6.5 W, 1.3 W) at valuable wavelengths (1060 nm, 1250 nm) for two-photon excitation of red-shifted fluorophores. These custom excitation sources are both simple to construct and cost-efficient in comparison to similar custom and commercial alternatives. Furthermore, they operate at a repetition rate (80 MHz) that allows fast image acquisition using resonant scanners. With our system we demonstrate compatibility with fast resonant scanning, the ability to acquire neuronal images, and the capability to image vasculature at deep locations (>1 mm) within the mouse cerebral cortex.