A study of doped polycrystalline diamond plates by non-destructive methods
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2023-01-01 |
| Journal | AIMS Materials Science |
| Authors | Itsh’ak Azoulay, Ory Klonsky, Yaniv Gelbstein, Peter Beker |
| Institutions | Ben-Gurion University of the Negev, Sami Shamoon College of Engineering |
| Analysis | Full AI Review Included |
Executive Summary
Section titled “Executive Summary”- Objective: Establishes non-destructive, real-time metrological methods (Air-SEM, wettability, UV-Vis-NIR absorption, PL spectroscopy, XPS) to correlate doping type with surface energy, wettability, and optical properties in CVD polycrystalline diamond (PCD).
- Materials Tested: Three 5 mm × 5 mm freestanding PCD variants—intrinsic (300 µm), nitrogen-doped (n-type, 300 µm), and boron-doped (p-type, 50 µm)—with a polished area of 25 mm2.
- Doping Concentration (ToF-SIMS): Boron ~1019 cm−3, Nitrogen ~1020 cm−3.
- Wettability Breakthrough: Bulk doping enables tunable surface energy. Water Contact Angle (WCA) shifts from 50° (N-doped) → 60° (Intrinsic) → 75° (B-doped), with calculated SV surface tensions of 49, 41, and 28.8 mN·m−1 respectively.
- Imaging Innovation: Air-SEM at 15 keV successfully distinguishes n-type (dark) and p-type (bright) regions in un-coated, un-charged samples, eliminating the need for conductive coatings or vacuum chambers.
- Optical Signature: Nitrogen-related defect centers (H3, N3) detected across all samples via PL; intrinsic band gap (5.47 eV) confirmed via UV-Vis absorption.
- Engineering Significance: The paper explicitly notes a critical pain point: “a lack of control over high doping concentration” from the original supplier, emphasizing the need for manufacturers with tight dopant uniformity.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context / Method |
|---|---|---|---|
| Sample Dimensions | 5 × 5 | mm | Square freestanding PCD substrates |
| Sample Thickness (Intrinsic / N-doped) | 300 | µm | Standard freestanding PCD |
| Sample Thickness (B-doped) | 50 | µm | Thin-film freestanding PCD |
| Polished Area | 25 | mm2 | Surface characterization region |
| Boron Concentration (p-type) | 1019 | cm−3 | ToF-SIMS (15 kV Ga primary ion gun) |
| Nitrogen Concentration (n-type) | 1020 | cm−3 | ToF-SIMS (15 kV Ga primary ion gun) |
| Diamond Band Gap (Eg) | 5.47 | eV | Optical absorption onset |
| Max Excitation Wavelength (λmax) | ~227 | nm | UV-Vis-NIR spectrophotometer (Cary 5000) |
| UV-Vis-NIR Range | 175 - 3,300 | nm | Spectral scan window with Pb-smart detector |
| PL Excitation Source | 280 | nm | Delta Nano LED (UV pulsed) |
| Excitation Pulse Duration | 430.30 | ns | Deltaflex TCSPC system |
| TCSPC Detector Range | 185 - 650 | nm | TBX-A single-photon module |
| Timing Walk (Detector) | <250 | ps FWHM | Photon lifetime measurement precision |
| Water Contact Angle (N-doped) | 50 | ° | Sessile drop method, deionized water |
| Water Contact Angle (Intrinsic) | 60 | ° | Sessile drop method |
| Water Contact Angle (B-doped) | 75 | ° | Sessile drop method |
| Wettability Test Temperature | 26 ± 1 | °C | Controlled lab environment |
| Relative Humidity (Test) | 45 ± 5 | % | Controlled lab environment |
| LV Surface Tension (Water, 20°C) | 72.8 | mN·m−1 | Neumann model input |
| SV Surface Tension (Intrinsic) | 41 | mN·m−1 | Calculated via Neumann equation |
| SV Surface Tension (N-doped) | 49 | mN·m−1 | Calculated via Neumann equation |
| SV Surface Tension (B-doped) | 28.8 | mN·m−1 | Calculated via Neumann equation |
| XPS Base Pressure | 2.5 × 10−10 | Torr | UHV analysis chamber |
| XPS X-ray Source | 1,486.6 | eV | Al Kα monochromatic |
| XPS Energy Reference | 285 | eV | C1s peak binding energy |
| Air-SEM Beam Energy | 15 - 30 | keV | Variable primary electron energy |
| Air-SEM Membrane Thickness | 10 - 15 | nm | Electron-transparent window |
| Air-SEM Air Gap | 50 - 100 | µm | Ambient pressure region |
| Air-SEM Spatial Resolution | <10 | nm | At 15-30 keV |
| Contact Angle Drop Volume | 2 | µL | Standardized sessile drop |
| Contact Angle Repeatability | 3 - 10 | measurements | Per sample, varied regions |
Key Methodologies
Section titled “Key Methodologies”- Sample Acquisition: Procure 5 mm × 5 mm freestanding polished PCD plates (Intrinsic 300 µm, N-doped 300 µm, B-doped 50 µm) with verified dopant concentration via ToF-SIMS.
- Dopant Quantification: Perform Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS) using a 15 kV Ga primary ion gun to establish baseline [B] = 1019 cm−3 and [N] = 1020 cm−3.
- Optical Absorption Profiling: Scan samples from 175 nm to 3,300 nm using a Cary 5000 UV-Vis-NIR spectrophotometer with a Pb-smart detector; identify the 5.47 eV band edge.
- Photoluminescence (PL) Spectroscopy: Excite at 280 nm with a UV LED (430.30 ns pulse); capture emission from 185-650 nm using a TBX-A single-photon counting module to map defect centers (H3, N3).
- Decay Kinetics Measurement: Apply Time-Correlated Single Photon Counting (TCSPC) via a Horiba Deltaflex system to extract photon lifetime from the 25-525 ns window.
- Wettability Testing: Deposit 2 µL deionized water sessile drops (resistivity 18 MΩ·cm, pH 5.5) at 26 ± 1 °C and 45 ± 5% RH; measure WCA via optical goniometry (3-10 readings per region).
- Surface Tension Calculation: Apply the Neumann equation-of-state model using a universal constant β = 0.0001247; solve iteratively via the dichotomy method for SV and SL interfacial tensions.
- Surface Chemistry Analysis: Execute X-ray Photoelectron Spectroscopy (XPS) at 2.5 × 10−10 Torr using an Al Kα source (1486.6 eV), referencing C1s at 285 eV to track oxygen concentration shifts.
- Ambient Electron Imaging (Air-SEM): Image un-coated, isolated samples at 15 keV and 30 keV using backscattered and secondary electron detectors to differentiate dopant contrast without vacuum or metallization.
- Dopant Contrast Mapping: Use the optimal 15 keV beam energy—where penetration depth < SE escape depth—to achieve clear p-type (bright) vs. n-type (dark) contrast.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”Applicable Materials
Section titled “Applicable Materials”To replicate or extend the findings of this study, the following 6CCVD offerings map directly to the dopant regimes investigated:
| Paper Requirement | 6CCVD Material Recommendation |
|---|---|
| Intrinsic PCD (300 µm, polished) | Optical-Grade Free-Standing PCD — high-purity, low-stress, Ra < 5 nm polish |
| Nitrogen-Doped PCD (300 µm) | N-Type PCD Wafers — controlled [N] from 1018-1020 cm−3 |
| Boron-Doped PCD (50 µm) | Light-to-Heavy BDD PCD — [B] from 1018-1021 cm−3, freestanding or on-substrate |
| Large-area monitoring (Air-SEM scope) | PCD Plates up to 125 mm — accommodates oversized in-line QA samples |
| Thin-film B-doped (50 µm target) | Ultra-Thin PCD / SCD Films — available from 0.1 µm to 500 µm |
Customization Potential
Section titled “Customization Potential”The paper’s authors explicitly flag supplier inconsistency at high doping levels as a critical bottleneck. 6CCVD mitigates this risk through:
- Precision Doping Control: Custom [B] and [N] targets verifiable by ToF-SIMS, eliminating the “lack of control” noted in the original work.
- Custom Metalization (Internal Capability): Au, Pt, Pd, Ti, W, Cu — enabling follow-on experiments such as contact-angle evolution under metallized electrodes, Schottky barrier mapping, or electrochemical BDD characterization.
- Laser Cutting & Dicing: Tight-tolerance square, rectangular, or irregular geometries from mm-scale coupons up to 125 mm wafers—ideal for Air-SEM staging, multi-region wettability mapping, or optical spectroscopy sample prep.
- Surface Finishing: Sub-nanometer Ra polish on SCD and < 5 nm Ra on inch-size PCD ensures the smooth, homogeneous surfaces required by the Neumann equation (Wenzel-compliant regime).
- Thickness Flexibility: 0.1 µm - 500 µm (SCD/PCD) and up to 10 mm substrates—covering the 50 µm thin-film B-doped case as well as thick free-standing plates.
Engineering Support
Section titled “Engineering Support”The correlation between doping concentration, surface energy, and optical defect density is non-trivial. 6CCVD’s in-house PhD team can assist with:
- Material Selection: Matching dopant concentration and grain morphology to your target WCA, PL emission, or electrochemical window.
- Process Design: Recommending optimal growth parameters for tunable wettability (the paper demonstrates WCA shifts of 25° purely via doping chemistry).
- QA Protocol Development: Establishing Air-SEM or PL-based incoming inspection protocols for your doped-diamond inventory.
Call to Action
Section titled “Call to Action”For custom specifications, dopant concentration consultation, or to request a quotation on PCD, SCD, or BDD substrates tailored to your metrology or device roadmap, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
<abstract> <p>Diamond offers great promise as a solution to some of the limitations of current state of the art semiconductor technologies. Yet, significant challenges associated with the doping process remain a primary impediment to the development of diamond-based electronic devices. At present, it is unclear which simple measurement methods are needed to evaluate the diamond doping process. We propose non-destructive inspection methods for evaluating the polycrystalline chemical vapor deposition (CVD) diamond doping process, by analyzing the wettability, optical absorption, photoluminescence emission spectroscopy and atmospheric scanning electron microscope (Air-SEM) tests. Our results show that the properties of the measured samples are distinctly changed due to the presence of the doping elements, thereby confirming the effectiveness of these non-destructive methods for the diamond production industry.</p> </abstract>