Fast and accurate measurement of small field dosimetry using a novel scintillation detector
At a Glance
Section titled “At a Glance”| Metadata | Details |
|---|---|
| Publication Date | 2025-11-30 |
| Journal | Journal of Applied Clinical Medical Physics |
| Authors | Yiding Han, Jingzhu Xu, Yao Hao, Baozhou Sun |
| Institutions | Baylor College of Medicine, Washington University in St. Louis |
| Analysis | Full AI Review Included |
Executive Summary
Section titled “Executive Summary”- A water-equivalent plastic scintillation detector, BP-PSD model 11, was evaluated for small-field dosimetry using a Varian TrueBeam 6XFFF photon beam.
- The detector contained a 1 mm diameter × 1 mm long cylindrical scintillator with a calculated sensitive volume of 0.785 mm³, supporting high-resolution measurements in fields as small as 0.5 × 0.5 cm².
- Field output factors were measured for 0.5 × 0.5, 1 × 1, 2 × 2, 3 × 3, and 4 × 4 cm² MLC-defined fields, using a 10 × 10 cm² jaw-defined reference field.
- The BP-PSD agreed with established detectors to within 1% for fields of 1 × 1 cm² and larger, and within 1.6% for the 0.5 × 0.5 cm² field.
- Beam-profile measurements showed less than 1% variation in penumbra length between BP-PSD, micro-diamond, and micro-silicon diode detectors.
- The indirect percentage-depth-dose method acquired profiles at 31 depths and reduced total acquisition time from approximately 40 minutes to less than 8 minutes, corresponding to a reported 5-10 times faster workflow.
- The results support BP-PSD technology for small-field commissioning, stereotactic radiotherapy, radiosurgery, and high-throughput radiotherapy QA, particularly where detector volume, water equivalence, and acquisition speed are important.
Technical Specifications
Section titled “Technical Specifications”| Parameter | Value | Unit | Context |
|---|---|---|---|
| Radiation source | Varian TrueBeam | — | Linear accelerator used for all measurements |
| Photon energy | 6XFFF | MV | Flattening-filter-free photon beam |
| Field sizes | 0.5 × 0.5, 1 × 1, 2 × 2, 3 × 3, 4 × 4 | cm² | Small-field measurements |
| Reference field | 10 × 10 | cm² | Jaw-defined reference field for output-factor normalization |
| Source-to-surface distance | 100 | cm | Water-tank PDD and profile measurements |
| Output-factor measurement SSD/depth | 95 / 5 | cm | First output-factor configuration |
| Output-factor measurement SSD/depth | 90 / 10 | cm | Second output-factor configuration |
| Scintillator diameter | 1 | mm | Cylindrical BP-PSD scintillation core |
| Scintillator length | 1 | mm | Cylindrical BP-PSD scintillation core |
| Sensitive volume | 0.785 | mm³ | Calculated cylindrical volume |
| Scintillator composition | Polystyrene core with acrylic cladding | — | Fluorescent dopants added to optimize response |
| Integration window | 750 | µs | Two interleaved integrator channels |
| Number of acquisition channels | 2 | — | Sensor and Cerenkov correction channels |
| Adjacent channel ratio | 0.963 | — | ACR correction factor for the two channels |
| Sensor-channel signal | Rs | nC | Includes PSD and Cerenkov contributions |
| Cerenkov-channel signal | Rc | nC | Records Cerenkov contribution |
| Calibration factor | cGy/nC | — | Cross-calibrated against a calibrated ion chamber |
| Rolling-smoothing window | 40 | ms | Applied to pulse-by-pulse BP-PSD data |
| Spatial interval at 10 mm/s | 0.4 | mm | Effective sampling interval from the 40 ms window |
| Spatial interval at 20 mm/s | 0.8 | mm | Effective sampling interval from the 40 ms window |
| BP-PSD fast scan speed | 20 | mm/s | Vendor-recommended speed for PDD and profiles |
| BP-PSD indirect PDD scan speed | 10 | mm/s | Profiles acquired at multiple depths |
| Reference detector scan resolution | 1 | mm | Coarser spatial sampling for comparison detectors |
| Reference detector scan speed, 2 × 2 and 3 × 3 cm² | 2 | mm/s | Micro-diamond and micro-silicon measurements |
| Reference detector scan speed, 0.5 × 0.5 and 1 × 1 cm² | 1 | mm/s | Micro-diamond and micro-silicon measurements |
| Profile comparison depths | 1.3, 5, 10 | cm | Field sizes from 0.5 × 0.5 to 3 × 3 cm² |
| Indirect PDD profile count | 31 | profiles | Acquired from the water surface to 280 mm depth |
| Indirect PDD depth range | 0-280 | mm | Water surface through 28 cm depth |
| Indirect PDD depth interval | 1-10 | mm | Variable depth spacing between profiles |
| Gamma criterion | 3% / 1 mm and 2% / 2 mm | — | One-dimensional PDD comparison criteria |
| Gamma passing rate for PDD | 98 | % | BP-PSD compared with ion chamber for 3 × 3 and 10 × 10 cm² fields |
| 3 × 3 cm² penumbra length | 4 | mm | Measured BP-PSD result; literature range 3.86-4.2 mm |
| FOF variation, 1 × 1 cm² and larger | <1 | % | Comparison among detectors and measurement configurations |
| FOF variation, 0.5 × 0.5 cm² | 1.6 | % | Maximum reported inter-detector variation |
| Indirect-PDD agreement, 0.5 × 0.5 cm² | <1 | % | Agreement with corrected results from other detectors |
| Total acquisition time, direct method | Approximately 40 | min | Conventional small-field PDD workflow |
| Total acquisition time, BP-PSD indirect method | <8 | min | Profile-based PDD reconstruction |
| Reported speed improvement | 5-10 | times | Compared with traditional small-field dosimetry methods |
Key Methodologies
Section titled “Key Methodologies”-
Detector preparation
- Use the Blue Physics BP-PSD model 11 system.
- Operate with a 1 mm diameter × 1 mm long cylindrical scintillator.
- Use the polystyrene core, acrylic cladding, fluorescent dopants, optical fibers, removable cartridge, acquisition unit, and BlueSoft software.
-
Signal acquisition and Cerenkov correction
- Record the detector response using the Sensor Channel, designated Rs.
- Record the radiation-induced optical background using the adjacent Cerenkov Channel, designated Rc.
- Apply the adjacent channel correction using an ACR of 0.963.
- Remove the Cerenkov contribution and convert the corrected signal to dose using a calibrated ion-chamber-derived factor.
-
Pulse-to-pulse data processing
- Process the pulse-by-pulse BP-PSD signal rather than relying only on integrating detector output.
- Apply a 40 ms rolling-smoothing window to reduce pulse-level fluctuations before comparison with integrating detectors.
-
PDD and profile measurement
- Scan the 6XFFF beam in a water tank at 100 cm SSD.
- Use BP-PSD scan speeds of 10 and 20 mm/s.
- Measure beam profiles at 1.3, 5, and 10 cm depths for field sizes from 0.5 × 0.5 to 3 × 3 cm².
- Compare profiles against micro-diamond and micro-silicon diode detectors.
-
Indirect PDD reconstruction
- Acquire 31 lateral beam profiles from the water surface to 280 mm depth.
- Use variable depth intervals between 1 and 10 mm.
- Identify the central-axis position from the peak of each profile.
- Assign the peak dose at each depth to generate an indirect PDD curve.
- This approach reduces sensitivity to detector misalignment and beam inclination.
-
Direct PDD validation
- Measure direct PDDs with the PTW Semiflex ion chamber, model TN31013, with a volume of 0.07 cm³.
- Use PTW BeamScan Pre-Scan Centering and Beam Inclination Correction where detector communication is available.
- Exclude the build-up region for the stated gamma comparison, using depths greater than 5 mm.
-
Field output-factor measurement
- Measure output factors at SSD = 95 cm, depth = 5 cm and SSD = 90 cm, depth = 10 cm.
- Use MLC-defined fields from 0.5 × 0.5 to 4 × 4 cm².
- Normalize results to a 10 × 10 cm² jaw-defined field.
- Apply TRS-483 principles, including correction factors for the micro-diamond and micro-silicon detectors.
-
Performance evaluation
- Compare BP-PSD measurements with Exradin W2, micro-diamond, micro-silicon diode, and ion-chamber results.
- Use 1 mm / 3% and 2 mm / 2% one-dimensional gamma criteria for PDD assessment.
- Define penumbra as the lateral distance between the 20% and 80% normalized dose positions.
6CCVD Solutions & Capabilities
Section titled “6CCVD Solutions & Capabilities”Recommended 6CCVD Material
Section titled “Recommended 6CCVD Material”- Optical Grade SCD is the preferred material for high-resolution, water-equivalent radiation-sensing and dosimetry components.
- SCD is suitable for further development of compact scintillation or radiation-sensitive elements because it can be supplied as thin plates with precise thickness control.
- 6CCVD SCD is available from 0.1 µm to 500 µm thickness, enabling reduced detector active volumes and improved spatial resolution.
- Where the application requires a larger active area, robust electrical response, or a lower-cost detector body, high-purity PCD is a suitable alternative.
- For applications requiring a conductive sensing element, boron-doped PCD should be evaluated as a customized functional material.
Geometry and Surface Control
Section titled “Geometry and Surface Control”- 6CCVD can supply SCD plates and wafers with thicknesses down to 0.1 µm, allowing detector manufacturers to investigate ultrathin active regions.
- Custom dimensions are available, including PCD plates or wafers up to 125 mm.
- SCD surfaces can be polished to Ra < 1 nm, supporting low-scatter interfaces and controlled optical or electrical response.
- Inch-size PCD can be polished to Ra < 5 nm, providing a practical surface for detector substrates, fixtures, and experimental prototypes.
- Thin SCD and PCD formats can be used to study the relationship between detector volume, field perturbation, and spatial resolution in extremely small radiation fields.
Customization Potential
Section titled “Customization Potential”- 6CCVD can customize diamond dimensions and thickness to match the active-volume requirements of small-field dosimeter designs.
- Internal metallization capability is available for Au, Pt, Pd, Ti, W, and Cu.
- Metallization can be specified for electrodes, conductive tracks, contact pads, bonding surfaces, or segmented detector structures.
- Customized metal stacks can be developed according to the required work function, adhesion, radiation resistance, and electrical conductivity.
- 6CCVD can discuss laser cutting and custom shaping for SCD and PCD components where prototype geometry requires non-standard outlines, apertures, or arrays.
- Material and electrode configurations can be tailored for SCD, PCD, or BDD detector architectures.
Engineering Support
Section titled “Engineering Support”- 6CCVD’s in-house PhD team can assist with material selection for small-field radiotherapy dosimetry, scintillation-detector development, and high-resolution radiation-sensing applications.
- Engineering support can address:
- SCD versus PCD selection.
- Active-layer thickness and detector volume.
- Surface roughness and optical finish.
- Electrode material and metallization stack selection.
- Charge collection and conductivity requirements.
- Mechanical tolerances, cutting, and wafer-level processing.
- Reproducibility and batch-to-batch material characterization.
Application Alignment
Section titled “Application Alignment”- The paper demonstrates that detector size, water equivalence, response speed, and alignment control are central to accurate small-field measurements.
- 6CCVD SCD can support research aimed at minimizing detector perturbation while preserving mechanical stability and signal quality.
- The paper’s use of a 1 mm × 1 mm scintillator highlights the value of thin, precisely fabricated diamond materials for further miniaturization studies.
- 6CCVD materials are relevant to components for:
- Small-field output-factor measurement.
- Beam-profile characterization.
- Percentage-depth-dose measurement.
- Stereotactic radiosurgery and radiotherapy QA.
- Radiation-sensitive and scintillation-based detector prototypes.
- High-resolution, low-volume radiation sensors.
Practical Specification Recommendation
Section titled “Practical Specification Recommendation”- Begin with Optical Grade SCD when the priority is a low-scatter, high-purity active material.
- Specify the thinnest practical SCD layer compatible with handling and signal amplitude, with available thicknesses from 0.1 to 500 µm.
- Request Ra < 1 nm SCD polishing for surfaces intended to interface with optical or electrical structures.
- Use Ti/Au or Ti/Pt/Au metallization where appropriate, with the final stack selected according to the detector’s electrical and packaging requirements.
- For larger-area or more mechanically robust prototypes, evaluate PCD or BDD as an alternative or complementary material.
- 6CCVD can support prototype discussion from material selection through dimensional specification and metallization planning.
For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.
View Original Abstract
Abstract Background The most used instruments for small‐field dosimetry have notable limitations, including the need for correction of output factors, limited scanning speeds, and challenges in alignment for percentage depth dose (PDD) measurements, particularly for extremely small fields. However, plastic scintillation detectors (PSDs) are an attractive alternative for small‐field dosimetry due to their correction‐free nature, linear dose response, and fast response time. Purpose This study evaluates the robustness and accuracy of the dosimetric measurements using a new water‐equivalent PSD in small‐field dosimetry. The study also aims to report accurate measurements of output factors, profiles, and an indirect method for measuring PDD in small fields, with a scanning time that is 5 to 10 times faster than traditional methods. Method PDDs, profiles, and output factors were measured on a Varian TrueBeam 6XFFF photon beam for the field sizes of 0.5 × 0.5 cm 2 , 1 × 1 cm 2 , 2 × 2 cm 2 , 3 × 3 cm 2 , and 4 × 4 cm 2 using a new PSD from blue physics (BP‐PSD). These measurements were compared with those obtained using a well‐established PSD (Standard Imaging W2), micro‐diamond (TN60019, PTW‐Freiburg, Germany), and micro‐silicon detectors (TN60023, PTW‐Freiburg, Germany). Owing to its fast response, the BP‐PSD enabled the collection of beam profiles at 31 depths, which were used to derive the PDD while avoiding detector misalignment along the beam path. Data was collected in a water tank controlled by the PTW BeamScan software. The pulse‐by‐pulse raw data from BP‐PSD were converted to respective dosimetry data using in‐house software. Result The BP‐PSD demonstrated excellent agreement with other detectors for small‐field output factors (FOFs), with a maximum variation of 1.6%. The BP‐PSD also showed strong agreement in PDD measurements with an ion chamber (TN31013) for both 3 × 3 cm 2 and 10 × 10 cm 2 field sizes, achieving a 98% gamma passing rate (gamma criteria: 1 mm, 3%). For the profile measurements, the BP‐PSD showed consistency with both the micro‐diamond and micro‐silicon diode detectors, with less than 1% variation in measured penumbra length. At a 3 × 3 cm 2 field size, the measured penumbra length (4 mm) agreed with previously published data (3.86-4.2 mm). Additionally, for an extremely small field size (0.5 × 0.5 cm 2 ), the indirect PDD measurements derived from profiles showed significant improvement compared to the direct measurement without beam inclination correction. Conclusion The BP‐PSD has proven to be a robust and reliable detector for small‐field dosimetry. It shows excellent agreement with other detectors in measuring small FOFs, profiles, and PDDs, while achieving significantly faster scanning speeds in a water tank.
Tech Support
Section titled “Tech Support”Original Source
Section titled “Original Source”References
Section titled “References”- 2013 - Small photon field dosimetry using EBT2 Gafchromic film and Monte Carlo simulation