Skip to content

Thermal boundary resistance of direct van der Waals bonded GaN-on-diamond

MetadataDetails
Publication Date2020-06-16
JournalSemiconductor Science and Technology
AuthorsWilliam M. Waller, James W. Pomeroy, D. Field, Edmund J.W. Smith, Paul May
InstitutionsUniversity of Bristol
Citations43
AnalysisFull AI Review Included
  • Objective: Quantify the thermal boundary resistance (TBR) of direct van der Waals (vdW) bonded GaN-to-diamond interfaces versus conventional GaN-on-diamond heterostructures that use a silicon nitride (SiN) interlayer.
  • Key Finding: Direct vdW bonding without a carbide-forming interlayer produces a high TBR of 220 ± 70 m2 K GW-1, approximately 7× higher than bonded interfaces using an optimized ~10s nm SiN interlayer.
  • Theoretical Approach: An adapted Acoustic Mismatch Model (AMM) incorporating Schoenberg’s linear slip boundary equations and Lennard-Jones (L-J) potential adhesion energy was implemented to predict phonon transmission probabilities.
  • Experimental Validation: Transient Thermoreflectance (TTR) measurements confirmed the weak-bond AMM prediction, validating that interfacial bonding strength—not bulk acoustic mismatch—is the dominant factor governing thermal transport.
  • CVD Diamond Growth: 2 µm polycrystalline diamond (PCD) films were grown directly on Ga-polar GaN using MWCVD (1100 W, 110 Torr, 4% CH4/H2, ~750°C).
  • Engineering Implication: Covalently bonded interfaces (via thin SiN or similar carbide-forming interlayers) are critical for achieving low thermal resistance GaN-on-diamond devices targeting ultra-high-power RF and wide-bandgap applications.
  • Significance: Establishes a rigorous modeling framework for designing next-generation Ga2O3-on-diamond, AlN-on-diamond, and other wide-bandgap semiconductor-diamond thermal management stacks.
ParameterValueUnitContext
Diamond film thickness2µmPolycrystalline diamond grown on GaN-on-Si
Bulk diamond thermal conductivity2200W m-1 K-1Single crystal benchmark
PCD thermal conductivity1200-1500W m-1 K-1Polycrystalline CVD diamond
SiC thermal conductivity (reference)~440W m-1 K-1Conventional GaN substrate
SiN thermal conductivity1-2W m-1 K-1Bonding interlayer (low-k)
GaN layer thickness1.03µmMOCVD-grown active layer
Measured TBR (vdW, no interlayer)220 ± 70m2 K GW-1Direct GaN-to-diamond
Predicted TBR (weakly bonded AMM)200m2 K GW-1Model output
TBR (with SiN interlayer)~30m2 K GW-1Literature benchmark
DMM prediction (welded GaN/diamond)< 5m2 K GW-1Diffuse Mismatch Model
TBR (Ga2O3-on-diamond vdW)~60m2 K GW-1Literature benchmark
TBR (Ga2O3-on-diamond measured)20× DMM prediction—vs. 3 m2 K GW-1 model
RF power density gain vs. SiC3×—Heterogeneous integration benefit
GaN transverse phonon velocity8.04 × 103m s-1Acoustic model input
GaN longitudinal phonon velocity4.13 × 103m s-1Acoustic model input
Diamond transverse phonon velocity17.52 × 103m s-1Acoustic model input
Diamond longitudinal phonon velocity12.82 × 103m s-1Acoustic model input
GaN density6150kg m-3Material property
Diamond density3515kg m-3Material property
Au transducer thickness100nmTTR measurement layer
Cr adhesion layer thickness10nmTTR transducer stack
Debye temperature (GaN)600KModel cutoff parameter
Adhesion energy γ (vdW model)0.0-2.0J m-2Sweep range
GaN lattice constant5.186 × 10-10mFCC Wurzite a-parameter
Diamond lattice constant3.567 × 10-10mFCC unit cell
  • Substrate Preparation: Standard GaN-on-Si wafers with 1.03 µm GaN layer (MOCVD-grown, Ga-polar orientation) used as starting templates.
  • Diamond Seeding: Ga-polar GaN surfaces pre-seeded with a mixture of micro- and nano-diamond particles using an electrostatic spray technique to ensure uniform nucleation.
  • CVD Diamond Growth (MWCVD):
    • Reactor: 1.5 kW, 2.45 GHz ASTeX-type
    • MW input power: 1100 W
    • Chamber pressure: 110 Torr
    • Gas chemistry: 4% CH4 in H2
    • Duration: 4 hours
    • Substrate temperature: ~750°C (deliberately low to minimize thermal expansion mismatch strain and prevent GaN cracking/delamination)
    • Resulting film: 2 µm polycrystalline diamond
  • TTR Transducer Deposition: 10 nm Cr adhesion layer + 100 nm Au transducer sputtered onto the diamond surface for thermoreflectance measurements.
  • Thermal Characterization: Transient Thermoreflectance (TTR) performed with an axisymmetric heat diffusion model fitted to measured traces; diamond-to-GaN TBR was the most sensitive fitting parameter at time scales >100 ns.
  • Theoretical Modeling (Adapted AMM):
    • Applied Schoenberg’s full linear slip interface formulation with three phonon polarizations (P, SV, SH).
    • Calculated transmission probabilities for welded vs. weakly bonded cases across four mode-conversion channels.
    • Integrated phonon transmission over Debye density of states up to Debye cutoff of GaN (600 K), evaluated at 300 K.
    • Spring constant per unit area (KA) linked to adhesion energy via Lennard-Jones potential using Lorentz-Berthelot mixing rules.
  • Validation: TBR predicted by the weak-bond AMM (200 m2 K GW-1) was benchmarked against TTR experimental measurement (220 ± 70 m2 K GW-1).
  • Applicable Materials:
    • Optical/Mechanical Grade PCD (Polycrystalline Diamond): Required in the 0.1 µm-500 µm thickness range to replicate or extend this research. The 2 µm films demonstrated in this work correspond well to our standard free-standing PCD and diamond-on-substrate capabilities.
    • Single Crystal Diamond (SCD): For follow-on studies requiring the ultimate bulk thermal conductivity ceiling (2200 W m-1 K-1), our SCD substrates up to 10 mm thick provide a high-purity heat spreader baseline.
    • Heavy Boron-Doped PCD (BDD): When the application transitions from thermal management to integrated electrothermal devices (e.g., electrochemical + thermal hybrid systems), boron-doped variants deliver tunable electrical conductivity without sacrificing thermal performance.
  • Customization Potential:
    • Wafer-Scale PCD up to 125 mm: Supports large-area GaN-on-diamond heterostructure fabrication with uniform thermal boundary characteristics, eliminating edge-to-edge variation seen in smaller coupons.
    • Custom Metalization (Internal Capability): The paper’s TTR transducer stack (Cr 10 nm / Au 100 nm) is a standard 6CCVD metallization sequence. We also offer Ti, Pt, Pd, W, and Cu stacks, with full customization of adhesion layer chemistry, thickness, and deposition order to match specific TTR or device contact requirements.
    • Laser Cutting & Dicing: For patterning diamond heat spreaders into discrete device footprints while maintaining sub-surface damage control and Ra < 5 nm polished surfaces.
    • Surface Polishing: Ra < 5 nm on inch-size PCD and Ra < 1 nm on SCD ensures minimal phonon scattering losses at the back-side diamond interface.
  • Engineering Support:
    • 6CCVD’s in-house PhD engineering team is available to assist with material selection for GaN-on-diamond, Ga2O3-on-diamond, AlN-on-diamond, and other wide-bandgap semiconductor thermal management stacks—including TBR optimization, adhesion layer design, and AMM/DMM model validation.
    • We can supply matched-diameter PCD wafers designed for direct vdW or covalent bonding experiments, with controlled nucleation density, grain size, and sp3/sp2 ratios to support reproducible transient thermoreflectance studies.
    • Custom seeding protocols (analogous to the electrostatic spray seeding used in this work) can be developed for non-diamond substrates including GaN, SiC, AlN, and 2D material heterostructures.

For custom specifications or material consultation, visit 6ccvd.com or contact our engineering team directly.

View Original Abstract

Abstract Carbide forming interlayers, such as amorphous silicon nitride, are typically used for GaN-on-diamond heterogenous integration. This interlayer has a low thermal conductivity, introducing an additional extrinsic interfacial thermal resistance. It may therefore be advantageous to omit this layer, directly bonding GaN-to-diamond (van der Waals bond). However, weakly bonded interfaces are known to increase the intrinsic thermal boundary resistance. An adapted acoustic mismatch model has been implemented to assess which bonding approach is the most optimal for low thermal resistance GaN-on-diamond. A high thermal boundary resistance of 200 m 2 K GW −1 is predicted for weakly bonded GaN-to-diamond interfaces, which is close to the measured value of 220 ± 70 m 2 K GW −1 , and ∼7× higher than values measured when a 10’s nm-thick SiN interlayer is included. Covalently bonded interfaces are therefore critical for achieving low thermal resistance GaN-on-diamond.